Nice addition to your truck. I'll bet it feels like a blessing getting in and out especially at our age.

Just installed a pair on my F250 this morning. Very clear and handy video!

Took me 1.5 hours to do 1 step on my '12 silverado crew cab lol.. the rocker panel isn't solid and has spaces and reinforcement panels so it was hard to get it lined up and centered. Make sure to get a car wash first because I had dirt falling all over me which was a pain

Very good and informative video. Good work!

Damn im in the process of fabbing my own steps that mount straight to the frame with existing holes

Why don't you open the door, instead of trying to guage the area where the step is giong to be mounted.....

Well done brother! 👊

Thanks! WAY better than the instructions.

Very helpful, precise and to the point! Thank you very much, JimmyVern

Why can't you just mark the holes while you had it up there testing it.

nice work

The directions say to use 1/8" to a 5/16" hole. Where do you get the drill bit you mentioned from?

These came on my dodge when I bought it, rockers were rusted to hell, these were held on basically by a chunk of rust. Got rid of them, installed new rocker panels and Bedlined it...never will I ever drill into my rockers. If you wanna be cheap go ahead and do it, just spray about a gallon of paint around your drill holes and hope water doesnt get in there. Gonna fab up some Nerf bars soon.

My truck is 16 inches from the ground how low do these hoops go

Good job

will this fit a Chevy 2012 Silverado lifted ?

Last time i watch a video by Pedro. Not smart

Trying to mount bbs1103-2 on a75 f-150

Nice!

I can find any. On here to help you put on step size on a Toyota Tacoma Name of step size are rhino you if Amy boby can help I can sure use the help thank you

Will that work on a silver truck. ?

Ese estribo queda mejor pasando un perno 3/8 con un fish wire y colocando una arandela en la parte trasera para cuadrar la pieza.. un tornillo autorroscante tiende a aflojarse...

Padre el vídeo Y no hay forma para crearlos uno mismo? O me podrás pasar medidas de los soportes y de la base final

What if the rocker panel is rusted?

Way to complicated! Should be a bracket to the frame with two bolts! Not drilling into the rocker planes! It's going to rust an fall clean off,especially in Ohio salt and my 350lb wife!

Wondering if any one else had this issue. When I received these, the mounting brackets were not the multi mounting brackets. They are not the ones that are in this video. I have reached out to carr about the issue, but I have not gotten a response. I purchased them back in November of 2016. The mounting brackets that came with the Hoop II step's look cheaper and the installation will be completely different from this video. any one else have this issue?

Wow mine comes with only one step in my box

Not so easy, but I like

Is it just me, or do you resemble Tiger Woods?

"drill holes" no like

Move brake cable to the side, Check!

with 2 big holes in your rocker panel leaving the fresh cut metal to the one spot condensed water likes to settle...... hmm..... new truck? don't do it... old truck? do it anyway you like...

Holy cow... who tf edited this video?

really don't like the idea of using rocker panel asking for problems. Frame mount is the way to go

Now what I am doing here is typing a comment, I have just typed a comment.

Thought i was watching Scotty cause of the beginning lol

Open the freakin door to show the front of the seat.

Way to complicated!

If you used the proper tools then you wouldn't look like an incompetent dork. You can buy short drill bits or preferably an angle drill, but drilling on an angle is just bad workmanship and being ham fisted.

My truck is 16 inches from the ground how low do these hoops go