Best switch test video. It's the only one I've seen that explains that the bottom 2 pins are for cruise control. Good work.

Don't forget to check that the rubber grommet that the switch presses against has not fsllen off.

You are the first accurate video that explained how to lock in . Thank you !!!

Thank you. I’m going to try this later on. Looks way too easy. The brake sensor was listed as a possible reason I’ve had issues with my start button functioning.

Just what I needed to confidently replace the one on my 07 RAV4. Thanks for the clear video, dude!

Super helpful, for this girl at least. You made it very easy to understand. Unfortunately my brake switch is different ☹️

If I had to guess that rubber piece (which I found laying on the driver side floor under the break pedal) is causing most of the problems not necessarily the brake pedal sensor itself. Apparently this rubber piece breaks and falls off causing the brake pedal sensor tip not contacting the break pedal. I was able to fix it temporarily by using adhesive felt that is put on the bottom the legs of chairs and place it in between the tip of the sensor and where it is supposed to make contact with the brake pedal. Use a small screwdriver to push the tip of the sensor back to make room for the felt. Placing the adhesive side of the felt on the brake pedal helps to keep it in place. The break lights worked fine after I did this. This works until you can get professional help.

I greatly appreciate the straight forward and clear description of the process.

Thanks for a good clear and concise explanation of the brake switch, wire harness, and troubleshooting.

I had a unique situation where, for some reason, one of the 4 cables that's part of the connector became damaged and frayed. Possibly in-part to some grounding issues, as it was a negative cable. As a result, shifting out of park would work sometimes and not work. Over time it, got worse and very rarely ever did. I tested the switch after removing it, to replace it with a new one for the sake of it , and I didn't get any continuity from one of the negative leads, which was the pin that connects to the wire with the frayed cable. So my guess is that it was causing a bad connection and as a result, killed the switch. The pins used for cruise control was fine though. Never mash your brake pedals excessively when you have this issue in hopes that you can finally get it out of park. May create additional, unwanted damage; Thus means more money out of your pocket. Edit: I went to a dealer to get an estimate to diagnose & repair the issues and it came to just over $300. Did it myself for $30 for a wire & new switch.

like the video, Great content. enlarged view of the switch , Using multimeter to test Continuity - even a beginner could follow along to test the switch itself.

My breaking switch was causing transmission problems. Car sometimes would not move in reverse and when it did it suddenly would put on the breaks without me stepping on the break paddle! Freaking annoying untill I got the schematic of the switch for the 2007 Corolla and found out how the switch sends signals to the PCM which controls the ABS system and ECU! My believe was that the switch was faulty as my scanner detected the code and was causing the PCM to automatically enable the ABS like a ghost! Took it out and sprayed some electric cleaner all over and readjust the all switch where when the pedal is not pressed the button of the switch is free from any pressing. This fixed the problem and has been running like it was before! After 2 weeks on this fix I changed the transmission fluid and filter and Corolla runs even more smoothly! I ended up replacing the switch to a genuine updated version for peace of mind! Yes a faulty "Breaking Switch" causes transmission problems and most mechanics will fail to detect the issue!

Omg this video is so helpful I have a 2000 Lexus rx300 and my brake lights don’t come on and my gear shift will not move out of Park omg this was so helpful

Nice man ! Thanks for video and your time !

Straight to point brother

Great video, short, straight to the point and complete. Help me out with my problem. Thanks

*_Watching this for my automotive labs! Nice!_*

Very Clear and steady camera..Thank you..very helpful your video..

Before you do anything… Try this… My situation was my brake lights worked but I was having trouble getting the stick shift out of park. I sprayed some WD-40 on that button at the bottom of the switch and that was what the problem was! The damn thing was stuck… That’s all it needed. May not fix it for you but it sure did for me! Certainly worth trying before you do anything else… Now if your brake lights won’t shut off that is something else probably. But it was an instant fix.

I switched out this part on my 2014 CX-5 and solved the issue! Now my start button is flashing red. Everything seems to be working perfectly. Any advice? I’m hoping to avoid the $205 diagnostic fee at the dealership. The code reader at advanced auto parts just said it was an electrical issue

Hi, i found your video very interesting which I guess it’s related to my car’s problem. I have a nissan march 2004 car and everytime I press my pedal (brake) makes a continuous sound like a reverse sound. All my lights are working but don’t know why it makes sound. I tried my best to investigate and I found this white button above the pedal same as your video that part of the car.

So thankful for this test shown in the video. UNFORTUNATELY FOR ME mine is functioning so the simple fix is not the case for me. Stuck trying to find more information on what it could be..... 😭

Wondering on a mercedes ...how do you relearn the brake pedal sensor upon replacement?

Is it possible that when/if this switch fails...it affects the shift lock (being stuck in Park), but the brake lights still work?

This helped me reinstall the switch after it worked itself loose. Didn't see any rubber gomit. That is probable why it worked loose

Thank you for taking the time to make this video...

Well. You. Nailed this. ,everybody was telling me. Transmission problem….5000.00. To fix..instead it was 20. Dollars and all it was the back brake light switch…..THANKYOU!

Yep. Mine. Also. Was the brake light switch for brake pedal…..this is a ‘safety. Feature’

Not all brake light switches work the same, some of the Peugeot range have continuous continuity through the switch and pushing the brake pedal down breaks the connection.

Very easy to understand

Mines in a ford ranger and it's making quite a clicking noise kinder annoying. Once i press down on brake ok but when it reengage it clicks any solution?

thank you!

helped me out, but first had to find where to unscrew panel to access switch bumper.

Have to do this on my sister’s 2010 Insight

Brake lights stuck on 2011 gmc yukon. Changed switch already

My damn 2012 colorado and many other gm vehicles have this common parts failure. Good to carry a spare and fuses

So if the break lights work does it means its not this partvthat is the problem..do i move on to solanoid??

Good stuff.

I thought this was the cruise control cutoff switch not the break light switch they both must look very similar?

The cruise control on my father’s Prius just died….could one of the problems to cause this be this switch if it isn’t working?? TIA!! Jack

This was very helpful, thanks you!

Thank you for showing this :) i am planning to build diy electric vehicle and this really helped :)

thank you for the lesson and time in making this video

Thank you

Thanks a ton, I love you man!!!

question: does continuity start immediately when plunger STARTS to move? I don't have brake lights unless brake pedal depressed all the way, ie. only when plunger is fully released. thx

My esp light is continuously on, just wondering if the brake switch maybe the main culparat in all this... Hmm

Thanks bud, appreciate the very informational video! :)

Question, should the battery be unplugged to safely do this? I see you are touching the wires... Just want to safe.

Nice video thanks will test

I have no brake lights on my saab 900 turbo 1990 model converable , do all saabs have the same switch and position on the pedal

Thanks

awesome thanx!

Thank you so much! Fixed my car's tail lights with your video! Cheers from Brazil!

I have ohms reading, but no continuity on my brake switch

Simple. Thank you.

Does this switch also adjustable for the brake pedal depth or height? My crosstrek brake feel a little to deep. Any idea? Thanks.

Thank you. Good explanation

Do this control park lights

Thanks you help me a lot

Thank you so much

Only one side of my cars break lights aren't working. Would this be a switch problem.

i have no offside brake light but the other nearside and back window come on checked fuzes bulbs wires DO YOU THINK IT MIGHT BE THIS I HAVE NO WIRING DIACRAM FOR 2009 A CLASS.?

Thank you soooooo much :)

When I press the break paddle I can feel something shaking underneath the paddle is there anything wrong with the break?

Another indicator is you can't set cruise control speed.

What you think the problem can be as my brake lights are continuously on soon as I put my light switch on?

excellent

I think I need one of these because I was stuck in park and my brake lights wouldn’t come on. I had to keep messing with my brakes to get the lights to come on so I could finally switch gears

My 2005 Touareg often doesn't start, even with the new battery. A friend told me it's probably a relay switch under the brake pedal. Any ideas? I'm trying desperately to avoid a new car payment!

a 2000 Corolla has any view or access to the switch blocked by an air conditioner plastic tube, so you cannot access the switch to replace it. There MAY be other cars that way as well.

I changed the brake pedal switch and the light is stilll on. What do I do!?

Brake lights in my car are temporary will only work for 20 minutes after a cold start. Afterwards no brake lights and gear won't shift from P. Replaced Body control module and brake light switch many times still the same problem. Electrician is always able to get the brake lights to work manually / bypassing the switch. On testing everything seems to be working perfectly from body control module all the way to "just before the brake pedal area". It's not the switch, is there something else close to the brake light switch that might cause a temperamental brake light? Any ideas please? Mustang 5.0 2012 in Europe hence no one is able to fix it and I end up buying random parts after watching KZfaq videos. Thanks in advance

Easy fix 💯

Very informative, thank you

My break lights work but its still stuck in park. Any suggestions?

My car Won't shift from Park unless I put it on Neutral first - looks like this might fix it!

Mr "CarsNToys"; my problem is my PARKING Brake light on dash cluster flashes off & on intermittently. Sometimes when parking brake is disengaged, I can reach down and wiggle foot pedal & light will go OFF then flash ON & OFF again & again. Something is not right. Could you please explain what You would do to check the problem...(pertaining to my 2005 GMC Canyon)--Thank You----*UPDATE* > Found a short Video 'DIY with Michael Borders' on You Tube explaining how to easily Reset the ABS/Braking System in 20 seconds. Anyone with the same problem I had should TRY this amazingly easy method first.....it's worth the try.

if it is the Brake Pedal Sensor, would this blowup the fuse? On my car, I keep replacing the 10A fuse and it keeps burning: I have no brake lights working (three of them) and no cruise control. I am wondering if there is something else since you did not mention anything about fuses.

All my brake lights won't turn on when i brake so i hope replacing a fuse will fix it all. However, changing the brake light switch might be the solution if all else fails.

Thanks!

u might have helped me ill let u know tomorrow

Dose it work on isuzu 2004 kb 3lx double cab diesel

Just chage mine...i change the fuses before but now there not burn they are good! So dont know what to to because it still not turn on 😞

On my car the brake lights stay on after i release the pedal I physically have to get down there and pull on my pedal to get the lights to turn off. I dont feel my pedal budging at all but it clearly will turn my brake lights off untill i press the pedal again and the brake lights are stuck on until i give the pedal a pull again... is this switch the problem? The car is a 1993 240sx

I have a 2004 Mazda RX 8 and I replaced my switch but the little round green pad that the switch presses against broke off can you tell me what this called so I can order a new one please

The dealership said this is going to cost 1 hours labor to change this. 🤦‍♀️

شكر لك Thank you 👍🏻😁

My gear lock is working but break light is not working in corolla 2002 model

2005 Toyota Tundra break light switch to be replace

Mine works perfectly but the stopper pushes it away instead of just pushing thee button therefore leaving my brake lights on

make a video about Chevrolet lumina 2008 am not seeing here in KZfaq

What year is your car. Mines is a 2015, not in that location.

It's weird how the 08-14wrx hatchback is the only impreza that has this type of brake light switch

Where is it at on a 2004 Cadillac Escalade?

so you covered half the switch. The other half or the other two contacts in the switch work in opposite. Depressing the button make continuity on the smaller contacts. And there you go, now the entire switch is covered.

Mine beeps only when I push it that means it’s bad right?

I’ll have to take a look at my car in the morning they’re trying to charge me $232 to replace it at the shop thanks

I have a Kia Forte 2010, I see the switch do I need to take out anything before taking the switch out? Also can I drive my car without the switch?

Will this fix my cruise control that doesn't work?