Much respect for doing this hard work.

Another great job of explaining the tear down of a transmission.

Man I was hoping this would be a shuttle shift trans. I need to pull the forward/reverse clutch on mine soon and I'm not looking forward to it. Thanks for putting these videos up, they're really helpful.

@3:12 You have the whole tractor apart and you can still hear it running. LOL!!! Another great educational video, thanks!

you make that look way too damn easy, thanks for sharing

Hey there from MS here. I have a 674 IH that is stuck in low gear. Linkage appears to be fine. So would this be a transmission problem or a hydraulic pump problem?

I grew up on an all IH farm, running everything from a Super C to a 3586 "2+2" and during the 70's and 80's personally put close to 2500 Hrs on a 1976 IH 574. I just recently purchased an '88 Case IH 385 MFWD with 850 Hrs. One reason why I chose the 385 was I figured it to operate very similar to my old 574. I thoroughly enjoyed my 574, for a small utility I didn't think it could be beat, but I don't remember the clutch pedal feeling like the pedal on the 385. My 385 appears to be in pretty good shape except the clutch pedal seems to not start to engage the clutch until about an inch from the stop. Do you have any video you could post of how to properly adjust the clutch on the 74, 84, 85, & 95 series tractors and what are your thoughts about my 385's clutch pedal?

are you going to do the rear axel and differential next? I have a IH 374 that has developed a popping in the left side axel. It is really pronounced when riding sideways across a hill with the left side being on the low side

Hi Dave, i have an 685 case ih and i need to change the transmission with another one, how many time you think it would take to split/remove change the trans? Great video btw! Thanks

hey Dave from Texas,, i have an international 354 with a duel clutch,, is it possible to change the PTO bearings without splitting the tractor? and is the the 354 a POS from the factory,, thank you sir

Any easy way to change gear selector, maybe via pto hole in right side or? It is the rear one, for low and reverse. thank you and greetings from sunny Finland

Good day You make good videos. Why did you scrape this tractor, you said syncro & PTO. gear shot. How was motor. Thanks

hi man, was wondering where i can find a gasket for that pto drive shaft cover plate. cant find them anywhere

Nice video sir where are you located? Need some parts for a 1976 574. Lock in differential Thankyou.

Hello i like the video. Do you have a video of the range section being taken apart?

Hi, I bought them 955 months ago. There are problems with the transmission. More precisely with second speed. Turn it on but as soon as I release the clutch it pops out of position. I tried to remove the transmission cover without removing the cab but it is held by the left gearbox shaft. What coud be the problem, with the gears? Thank you for great videos.

Hello I have case 885 xl from 1988 and I dont know if my gearbox is good or not. Because if I'm going up the hill with loaded trailer and I stop my tractor dont go to the back is just standing but if I change to the turtle then goes backwards ( like my another tractor This is normal ) my question is this it normal? And is difficult to switch gear but only in this case ( when I standing with loaded trailer on a large incline and I have to change gear to a smaller one) BTW great job

hi there does those gears 4th and 3rd fit from 784 international to case international 795 cause seems only top shifter cover and fork are different

Hi I have a international 785xl and it runs great no problems, if it is out of gear it wines a bit in high torque amplifier then goes quiet in when put in low torque amplifier is this normal thanks nick

What would cause excessive fine metal buildup in transmission. Oil looks like metallic paint and I have to change oil frequently.With new filter trans and hydraulic work greatuntill the filter and screen start plugging up

I would like to see you put one together, it would be interesting to watch.

I noticed the rear axles are removed. Do they have to be removed to pull the transmisson

Thangs for video. What is a typical problem if the gearbox dont syncronice. I can get a 85 mod whit a problem i dont know what othere then its a sync problem. Must i dismantel all like you here to fix ore if i cud just botch it so it works? I asked the seller if the trackor moves at all and when the problem happends. Im a total noob at tractors. I do a little car work so i can a little. But removing the box i need something to lift and aslo place it on like you say. I think i cud rebuild the box if i had to. But why... iive in norway and a tractor cost a lot here. even a old 80s cost form 80-140nok thats about 100 nok is 10 usd almost. little less. This one i can get for 40nok. whit loader only.

My tractor will not go forward or reverse, would that always be a clutch issue. I can shift through the gears with the tractor running with no grinding or problem. But no forward or reverse while the teactor is running

Do you have a video for the torque amplifier on a 674?

Hi! I have a 624 which is leaking quite a bit from the pto engage lever on the side of the trans. Do I need to disassemble a lot to put a new seal in it, if it at all possible to find it.

ماهوه اسباب عدم ستدار الستيرن

I have a tractor IH 574, i have a problem when we start working it's just stops and looks like it's in Neutral, Then need to push again clutch pedal, and release then it goes, but it happens many times like that. the clutch is new. I hope you understood my problem thanks in advance for your helping

I enjoy yours vids but didn't quite see how you used the two screwdrivers to remove the eyeless c clips. Thanks

hi my IH 885xl range lever keeps jumping out of high gear whats the fix thanks

Quiet educational

I need a little hepl regarding gearbox IH from Volvo BM 500. I can send some video and photos for the problem. Could you help me?

Hi,how to split gearbox and diferential block?I remove clip on main shaft,but it still not moving.

which gear is the one that has a busted tooth around 7:35

Hey Dave I need your my grandad left me at 464 IH 1975,he taught me how to change the engine oil but I never showed me where to add hydraulic oil or transmission fluid I know the 464 and 454 are similarso if you could please post a video or reply back with pictures on where to add the oil I would appreciate it cuz I checked the and it's pretty much outI'm going to have this thing professional restored but I've got a little bit more work to do before it leaves and I know have a leek as I can just feel it and get by like three more days I have all my stuff done

hello mr canadian i have case ih 795 when ever i turn it in i find air in the hydraulic system and the only leak i have is in the orbital doe's it matter please answer me and thank you

Buenas noches tendra el manual de como armar el carrete de arriba de la caja dd cambios de 784 porfavor

I cannot get that shaft out? Removed the 4 bolts and the c clip no luck

Si me puedes ayudar cómo reparar la dirección de un 744 internacional gracias

لدي كاروبه الم تستدير تستدير بوش وعدم رفع الفدان الحرث

Buenas me gustaría saber cómo se desmonta la carcasa del grupo de un internacional95s. Porque le he quitado los tornillos abre un poco pero no quiero romperle nada gracias

Hi is there anyway of making a 885 I cab do 30k

Quiet educational