CASTING A DIAMOND RING | STEP BY STEP GUIDE

No video

CASTING A DIAMOND RING | STEP BY STEP GUIDE

Рет қаралды 28,658

Күн бұрын

IN THIS VIDEO I WILL SHOW YOU THE ENTIRE CASTING PROCESS WITH 18K WHITE GOLD, 95 MELEE VS F DIAMONDS AND 1.5CT VS E CENTER STONE.
THANK YOU FOR WATCHING.
MUSIC BY:
Track: Ikson - Alive [Official]
Music provided by Ikson®
Listen: ikson.lnk.to/a...
Track: Lost Sky - Where We Started (feat. Jex) [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Lost Sky - Where We St...
Free Download / Stream: ncs.io/WhereWeS...
Song: Sapajou - Lion
Music provided by Vlog No Copyright Music.
Creative Commons - Attribution 3.0 Unported
Video Link: • Sapajou - Lion (Vlog N...
Song: ASHUTOSH - Cuba
Music provided by Vlog No Copyright Music.
Video Link: • ASHUTOSH - Cuba (Vlog ...
Song: Culture Code - Make Me Move (feat. Karra)
Music provided by NoCopyrightSounds
Video Link: • Culture Code - Make Me...
Song: DEAF KEV - Invincible
Music provided by NoCopyrightSounds
Video Link: • DEAF KEV - Invincible ...
Follow me:
/ bnhantran
/ bnhantran

Пікірлер: 77

@ya9931 2 жыл бұрын

Beautiful ring 😍 Your video deserves more attention! Hope to see more in the future 👍🏻

@Bi_Nhan 2 жыл бұрын

Thank you

@kelvinaguilar3360 11 ай бұрын

For a piece of the same size I use a cylinder that is just 1.25" x 2.18" and it has worked excellent for me. less time in the oven (approx. 1½hr) and much less plaster.

@Bi_Nhan 11 ай бұрын

Thank you for your advice. I'll try that next time.

@nicosdemetriou2585 2 ай бұрын

Hi kelvin

@PointmanOps Жыл бұрын

Very nice finished product

@badb1812 7 ай бұрын

Кольцо по итогу получилось хорошее. Но литьё с большим браком. Я бы даже не стал с ним возиться. Клиент который платит хорошую сумму за данную модель (при том если ещё с бриллиантами) заслуживает достойного качества от начала до конца.

@Ozzy2341 2 жыл бұрын

Amazing work my brother please make more videos :)

@danielclau1858 9 ай бұрын

Very nice Video - step by step for good learning

@Bi_Nhan 9 ай бұрын

Thank you very much

@adamrobbins2091 Ай бұрын

Ohh man I use cautery pens too, the ones I use have gold connecting the batteries lol

@jamesstays7192 Жыл бұрын

WOW!! Amazing work!

@Bi_Nhan Жыл бұрын

Thank you

@Meiradiaadia 2 жыл бұрын

Muito bom.....Parabéns!

@weluvwilla 2 жыл бұрын

NHAN THE BEST!!!

@meeko81g39 Жыл бұрын

palladium white gold ? nice

@Bi_Nhan Жыл бұрын

No it wasnt.

@rajkumarverma6260 2 жыл бұрын

Best video

@gabrielpasche690 25 күн бұрын

perfect

@connormorrison8976 Жыл бұрын

I really want to cast an engagement ring and i have some questions about the process, is there any way i can message you?

@Bi_Nhan Жыл бұрын

Yes. There is a link to my facebook in the description. You can message me through it

@renezavala6574 Жыл бұрын

Nice!! Do you have to scale the ring at all in the 3D CAD model? Wondering if 14ct white gold shrinks when doing the casting.

@Bi_Nhan Жыл бұрын

I did not scale it, my casting never shrank, but got expanded a few times.

@kvri-beats 5 ай бұрын

Can you tell me about your polishing machine?

@barbaracovey 6 ай бұрын

Why not use a stainless steel whisk to mix the plaster instead of your hand?

@sarkistakessian1066 8 ай бұрын

Beautiful setting job

@Ozzy2341 2 жыл бұрын

Love your kiln, where did you buy it ?

@Bi_Nhan 2 жыл бұрын

Thank you. I cant quite remember, either Rio or Stull

@kvri-beats 5 ай бұрын

Can I know what's your micro motor brand pls

@Bi_Nhan 5 ай бұрын

It is foredom sr motor with quick change handpiece

@kvri-beats 5 ай бұрын

@@Bi_Nhan thank you bro , can you give me a link

@randallmccullough4876 Жыл бұрын

What resin do you use and what print setting for the printer?

@Bi_Nhan Жыл бұрын

I used Power Burn resin in this video and the setting from the resin website.

@marotoworks Жыл бұрын

How do you pass from 5:10 to 5:16? (before the magnetic chamer)

@Bi_Nhan Жыл бұрын

I cut off the sprue and filed the extra metal at the bottom shank.

@michaelhobart8423 5 ай бұрын

The 3d printer software is ZBrush and Blender?

@gmjewerlyworkshop5556 Жыл бұрын

hola que tipo de resina usas?

@jeremytherrien5199 Жыл бұрын

Hello,I see on the picture of the video that you had a failed cast . I have similar issue . Can you list there what you changed to have good result please it would really help me . Thank you and Nice video

@Bi_Nhan Жыл бұрын

My flask casting temperature was too high, then I changed it to 1000f. There are a lot of reasons that can cause it to fail. Let me know if I can help

@jeremytherrien5199 Жыл бұрын

Is there a way to contact you to talk in private . I just started my casting project and i have some question please . Thanks for your answer

@Bi_Nhan Жыл бұрын

You can connect with me on facebook at the link provided in the description above.

@ryanmundell3504 10 ай бұрын

what tools do you uses

@ga9098 2 жыл бұрын

Nice project! You cast and set all alone?

@Bi_Nhan 2 жыл бұрын

Yes, thank you

@ga9098 2 жыл бұрын

@@Bi_Nhan What resin do you use?

@Bi_Nhan 2 жыл бұрын

I used Powerresin/Burn

@sportydelite 2 жыл бұрын

@@Bi_Nhan did you use powerresin burn on the failed print as well ? Also what do you think went wrong with the first casting Investment powder ratio or resin not completely cured

@Bi_Nhan 2 жыл бұрын

Aaron Tucker : I used powerresin for both. I failed at first because I set the casting temperature too high , almost double of what it supposed to be

@grillzbytroy8870 6 ай бұрын

When u cast 14k yellow whatbos your preffered flask temp same 1000f as the nickel whitegold?

@Bi_Nhan 6 ай бұрын

There is a video in my channel that I casted a 14k YG bracelet, casting temp was 945f.

@grillzbytroy8870 6 ай бұрын

Thanks I'm getting ready to load a flask thanks brotha

@grillzbytroy8870 6 ай бұрын

@Bi_Nhan I think I cast before the inside diameter of flask was settled at 945.f in other words the flask was much hotter than the desired 945 I should have waited a bit longer for inner flask to match oven temp. I use the centrifugal casting aka spin casting. Same flask temp as vacuum? Just triple checking I am loading up another flask and trying to get a perfect cast

@Bi_Nhan 6 ай бұрын

@@grillzbytroy8870 I leave the flask in an oven at the casting temp for at least 1 hour. I have never used centrifugal casting so im not sure, but i guess it should be the same.

@grillzbytroy8870 6 ай бұрын

@Bi_Nhan thanks again brother. Much 👏 appreciated from California

@kvri-beats 5 ай бұрын

Wish you a wax printer you deserve more good things

@Bi_Nhan 5 ай бұрын

Thank you. I appreciate it very much.

@kvri-beats 5 ай бұрын

@@Bi_Nhan what do you think about the nsk motor instead of foredom

@kvri-beats 5 ай бұрын

@@Bi_Nhan this one kzfaq.info/get/bejne/jdp3jbJ4r7LLhJs.htmlsi=tx6YeRvlmeTJAKLY

@Bi_Nhan 5 ай бұрын

@@kvri-beats I think that is a good idea. NSK is the best

@geovannycordero08 2 жыл бұрын

Great video , questions whats the resin brand ))))

@Bi_Nhan 2 жыл бұрын

Thanks. Its Powerresin/burn.

@maxdavidovitch3559 6 ай бұрын

Bro got the dab charger sitting out

@td7324 2 жыл бұрын

this resin doesnt need post cure ?

@Bi_Nhan 2 жыл бұрын

I'm not sure if it does but I did not cure it, I just soaked it with denatured alcohol right after the print gets done

@juba3498 9 ай бұрын

What metal is this? Do you mind telling us your burnout settings and metal temperature?

@tacitozetticci408 Жыл бұрын

What CAD program did you use ?

@Bi_Nhan Жыл бұрын

It's matrix.

@Bokan. 2 жыл бұрын

3:11 what's machine

@Bi_Nhan 2 жыл бұрын

Casting machine

@Bokan. 2 жыл бұрын

@@Bi_Nhan vibrating

@ironmen0211991 Жыл бұрын

Nghi sao đúc cai nhẫn chut xí zô cai lap chà bá😏

@Bi_Nhan Жыл бұрын

Tại lúc đó chỉ có cái lap đó à hehe

@ironmen0211991 Жыл бұрын

@@Bi_Nhan 😩😩😩