Chain and Sprocket Design Assembly and Motion Study : Solidworks Tutorial

Рет қаралды 59,091

3 жыл бұрын

-Real Motion-
Chain Sprocket Design Assembly and Motion Study Full Tutorial in Solidworks
The Tutorial Consists of:
1. Design
2. Assembly
3. Motion Study
Follow the tutorial from start to finish, you will be able to create such a real motion of Chain Sprocket by own.
1. Straight Chain Sprocket Design Assembly Motion Study Tutorial
• Chain Sprocket Design ...
Hope you Like it.
Do Share your opinions in the Comments.
Some Similar Tutorials:
1. Slat Chain Conveyor Design Assembly and Motion Study
• Solidworks tutorial: S...
2. Elevating Conveyor Design Assembly and Motion Study
• Solidworks tutorial: E...
1. PLAYLIST Solidworks Motion Study Tutorials (with Design and Assembly)
• Solidworks Motion Stud...
Thanks for Watching.
Do Like Subscribe and Share.
Stay Connected.

Пікірлер: 74

@sergioloboo.santos4071 Жыл бұрын

Wonderful!!!! Congratulations!👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻💯

@SolidworksFunPraveenSingh Жыл бұрын

Many many thanks!!

@brandonmoralesmusic28 3 жыл бұрын

Best tutorial of chain motion study

@SolidworksFunPraveenSingh 3 жыл бұрын

Thank you so much.

@untungasmoro3417 3 жыл бұрын

Terima kasih banyak.

@DesignThenMake 2 жыл бұрын

Great work man👍

@SolidworksFunPraveenSingh 2 жыл бұрын

Thanks!!

@MegaSahil009 3 жыл бұрын

Thanks a lot Sir! much respect!

@SolidworksFunPraveenSingh 3 жыл бұрын

Most welcome! Glad u liked it.

@MegaSahil009 3 жыл бұрын

@@SolidworksFunPraveenSingh sir ive to make a 55 teeth sprocket for my chain of pitch 12.7mm, but the polygon has only upto 40 sides max, can you please guide me how to make this sprocket? i tried to make a 222.4604mm diameter construction circle and draw 55 lines of 12.70690863mm on it, but as soon as i try to equal it with the previous lines, the geometry gets error, please help im stuck here

@MrMuratx81 3 жыл бұрын

Good job!

@SolidworksFunPraveenSingh 3 жыл бұрын

Thanks!

@jagatutor 3 жыл бұрын

Wowo this realy good jobs brother. 😎😎😎 I like this tutorial 😎😎👍👍👍

@SolidworksFunPraveenSingh 3 жыл бұрын

Thank you so much 😀

@pewpew5721 2 жыл бұрын

Thank you sir!

@SolidworksFunPraveenSingh 2 жыл бұрын

You're welcome!

@aishwaryakotnur4678 3 жыл бұрын

great tutorial

@SolidworksFunPraveenSingh 3 жыл бұрын

thank you so much

@satyaparida120 2 жыл бұрын

just great having lot of patience good job

@SolidworksFunPraveenSingh 2 жыл бұрын

thanks a lot!

@Akash-vs1yh Жыл бұрын

is there a relation between pitch and number of teeth?

@bassil1226 3 жыл бұрын

thank yaa ma brotha from an otha mothaaa

@atquach4548 3 жыл бұрын

great

@SolidworksFunPraveenSingh 3 жыл бұрын

Thanks!

@ximth3d4ddyx Жыл бұрын

I recently attempted to recreate this motion study in Solidworks 2021, but it didn't work quite as intended. There were a couple of settings that had to be slightly different compared to this video as they didn't exist. Also I had to use basic motion (Not sure if this makes a difference). the most I could achieve was that the sprockets wobbled back and forth slightly, and the links rattled and attempted to buckle. Would you have any suggestions for me to try / look at to correct this? - Hinge joint I couldn't select both sketches so tried concentric mate between roller and pins. Apologies for the verbal diarrhea.

@fn326 3 жыл бұрын

What if you have a fix center distance? How do you design the path with or without Chain Tensioner? I'd be happy to watch another video about this.

@SolidworksFunPraveenSingh 3 жыл бұрын

the basic will be the same, whatever path you choose the total path length should be equal to pitch*number of links. This tutorial was for fixed centre distance & without tensioner. i will soon do a tutorial on with tensioner.

@fn326 3 жыл бұрын

@@SolidworksFunPraveenSingh I've found out a way to tackle my problem. Fix center distance with chain tensioner. Thanks to this part 2:02. What I did was set a center distance between sprockets, fix diameters on both sprockets, fix distance of tensioner center to any sprocket center. Then tangent all the lines. Lastly, path length dimension.

@SolidworksFunPraveenSingh 3 жыл бұрын

yes, you did right.

@SuperDagia 3 жыл бұрын

Nice

@SolidworksFunPraveenSingh 3 жыл бұрын

Thanks

@Dharvin-to9qq 2 жыл бұрын

Can't select the 2 same circle when create nthe hinge...what to do...pls help me🥺🥺

@GG-dg7qt 3 жыл бұрын

Hello, i need help with the last hinge joint, i cannot perform the last hinge joint as it appears with error, tried quite some times but still didn't work. Thank you.

@SolidworksFunPraveenSingh 3 жыл бұрын

make sure any link is not mated with the path sketch or fixed. Try These Techniques: > First mating links in let's Clockwise, when reaching second last link then Start mating Anti-clockwise (from 1st hinge joint towards last one) and reach to the last link. OR > delete some previous hinge joints and then again start mate OR > Lastly if still not happens then Create a New Assembly file and try.

@jhanolaer8286 2 жыл бұрын

i want to know the formula of motion of the chain

@williamhensley8322 3 жыл бұрын

59:34 What did you do different? You had just done the same mate a few moments earlier and it didn't work. Then you do it again and then it works. I have the same error as you got at 59:15. Now I have them all constrained but now it still says it's under defined. And now after repeating my save and rebuild, it says that it's fully defined.

@SolidworksFunPraveenSingh 3 жыл бұрын

i used the same Save & Rebuild then the final joints created. If u have noticed, till 57:38- selected hinges in anticlockwise from 57:44- started in clockwise direction Did u also do that? Because, i too received error while creating all the mates(leaving the last one) in only one direction either clockwise or anticlockwise.

@williamhensley8322 3 жыл бұрын

@@SolidworksFunPraveenSingh I searched through the comments and did what you suggested and ultimately because I more or less followed what you were suggesting in the comments, I was able to finally get it to work.

@ahmedtufail3441 3 жыл бұрын

Can your solidwork file for this?

@zaidansari2377 3 жыл бұрын

hello, I am not getting motion analysis option I only get basic motion and animation. I did the simulation using basic motion but I got a very weird Result, Please Help

@SolidworksFunPraveenSingh 3 жыл бұрын

see the tutorial from 1:04:05 . you need to ON solidworks Motion Add in.

@tanphuoc9351 5 ай бұрын

why not use midplane for extruded

@mikeomalley8241 3 жыл бұрын

It won't let me change length of path. comes up with warnings that can't be entered. I have slowed down video and have draw it twice. Both times won't let me subtrcat without over defining???

@SolidworksFunPraveenSingh 3 жыл бұрын

Make Sure: 1. You didn't add center distance between the Polygons 2. You didn't fix centres of any Polygon 3. Didn't Put the Center of Any one of Polygon at the Origin (as did in the tutorial) Then, It will work. Path Length can be modified.

@mikeomalley8241 3 жыл бұрын

@@SolidworksFunPraveenSingh Thank you, I will try that. All the Best to You Sir, MPO'

@adityakandalkar84 3 жыл бұрын

chain is not rotating along the path as you shown in 15.29 what to do?

@SolidworksFunPraveenSingh 3 жыл бұрын

15:15 did you make the pattern 'Dynamic'?

@adityakandalkar84 3 жыл бұрын

@@SolidworksFunPraveenSingh yes

@vrukshwallikate223 2 жыл бұрын

for motion study reach

@siddheshmahadik4595 2 жыл бұрын

Number of new element states 3 doesn't match number of old ones, 4. Such error is occurring while calculating.

@SolidworksFunPraveenSingh 2 жыл бұрын

do a new motion study

@MegaSahil009 3 жыл бұрын

@solidworks FUn sir ive to make a 55 teeth sprocket for my chain of pitch 12.7mm, but the polygon has only upto 40 sides max, can you please guide me how to make this sprocket? i tried to make a 222.4604mm diameter construction circle and draw 55 lines of 12.70690863mm on it, but as soon as i try to equal it with the previous lines, the geometry gets error, please help im stuck here

@SolidworksFunPraveenSingh 3 жыл бұрын

Pitch 12.7mm, Teeth 55 For Inscribed Circle Polygon- Pitch= 12.7mm Sector Angle= 360/55= 6.54545455 deg Inscribed Circle Radius= 111.04879765mm Try these steps; 1. Create a Construction Circle 2. Make a Side of 12.7mm (pitch line) tangent to the Circle 3. Draw two construction lines Joining the both ends of the Pitch line to the center of the circle 4. make Angle between those 360/55= 6.54545455deg 5. making circular pattern of that pitch line, using angular spacing between each pattern 6.54545455 deg, number of pattern 55

@MegaSahil009 3 жыл бұрын

@@SolidworksFunPraveenSingh yes sir, what I did is, made a construction circle, made a 12.7054mm line tangent to that circle via the lines midpoint. Then I made a center line at x axis (center of circle) and measured the 12.7045 endpoint distance with the x axis. Then I created a new sketch. Made a point at this distance from axis and used Circular Sketch pattern and created 55 instances, then used line tool to join all those points, now I'll start making the chain link and then proceed with the sprocket teeth. Thanks a lot sir. Your response time for help is amazingly fast! I'll recommend your channel to others. :)

@MegaSahil009 2 жыл бұрын

@@SolidworksFunPraveenSingh your method is much more simpler and awesome sir, i was able to make 90 teeth sprocket easily with your steps. thanks alot :)

@NejinPokharel 2 жыл бұрын

I tried so many times but for some reason I cannot make the hinge joint. Also, I cannot seem to perform any without deleting mate of top plane of the chain path and top plain of the assembly. UPDATE: Flipping mate alignment in mid plane mates did the job for me. Firstly, I created hinge joint between each component even if it was over defined and deleted those which was unsolvable and the mate right next to those which were unsolvable and mated them again so that only overdefined error was showing. Then inside the mid plane folder, I flipped the alignment of any one unsolvable errored mate. Then wollah, every error disappeared

@NejinPokharel 2 жыл бұрын

Creating the hinge joint overdefines the mid plain assembly

@SolidworksFunPraveenSingh 2 жыл бұрын

the chain path is made 'fix', then all individual mid plane mates created and then hinge joints creation started. are you getting this over-define msg just in first hinge joint or the last hinge joint?

@NejinPokharel 2 жыл бұрын

@@SolidworksFunPraveenSingh first hinge joint

@NejinPokharel 2 жыл бұрын

@@SolidworksFunPraveenSingh Can I email you screenshots? It's getting kinda weird

@SolidworksFunPraveenSingh 2 жыл бұрын

did you follow the every steps of the tutorial? because if anywhere anything left then it may not work.