Brilliant - thanks. I’m in Oz, so was concerned about the temp the chiller was allowing, and so this instruction set was perfect, and easy to follow.

I just found this video just in time. It's exactly what I need. I had a Vevor CW5000 delivered a few days ago for the DIY 60W laser cutter/engraver I just started to build. I read the instruction booklet briefly and was concerned that the default "intelligent" mode appears to set the temperature higher than I have been led to understand is ideal for the laser tube. It looks like it should be a breeze to set the chiller up correctly following this video. Thanks a lot.

Thanks for this video - the most straight forward set of instructions I could find on how to set this thing.

Only video I have seen that explains how to use this thing! Bravo

I can’t even begin to thank you for this video. Without this I never would’ve figured this out.

Thanks for making such an easy to understand video!!! Quick and straightforward!

Very helpful in setting up my 5200. Thanks for sharing.

Great videos! What temp in celcius should be maintained for a 60W or 80W C02 tube in a stinking hot shed in Adelaide? Do you add anything to the water (like radiator fluid (as I have seen elsewhere))? Or is it just Tap Water?

Best video by far!!!! Thanks worked perfectly!!!

just received a 130w laser. this setting has been in my way, thank you fellow Canuck errrr Canada t shirt wearer

Very simple and clear explanation.

Hi Just picked up a dead Piranha 5030t with this chiller. I am in the North of England so cold as, however think ill run these settings when i get the unit running. Thanks for this, very helpful as i have no documentation at all with the laser or chiller.

Great video! I needed to adjust mine to NOT chill during the winter when I have an aquarium heater in the tank.

Super Helpful your video, very clear and straightforward. Thanks for your explanation.

Setting up my cw-5200. I live in the US (Texas) where it's HOT most of the time. I'm terrified about choosing the wrong temperature. I have a 100 watt laser. Any advice?

How long did it take to fully cool down? Been trying to get an answer on this with no results.

Great job bro thank you

Very helpful. Thank you.

I appreciate you making this video so much. The "instructions" I received with my unit from China were not very useful. Thank you.

Thanks, the Chinese manual was giving me a headache, I have a CW5000 clone, B&H, instructions worked great.

Now where's the setting to disable the beeping noise when scrolling through menus?

Hi, what is the optimum temperature for an 130 W (80 mm diameter) Laser Tube?

Well done, thanks.

Hello, hope you see this! Help please. I have just bought 130W with 5250 chiller. The laser will run with chiller connected via alarm wire and turned off but gets water error message on Ruida when powered on. They have used 2 same color wires on alarm wire. I think we hhave decided the issue might be mis wiring at factory BUT, the wires are same color and its a 2 wire plug tat laser o 3 wires at chiller. The chiller manuals identifies as H1 as Red, H2 as Green, and H3 as Black. I have marked my 2 yellow alarm wires as 1 and 2. They had yellow wire 1 on red and yellow wire 2 on black, green ?? ground?? Is there anyway you can confirm that green is not connected to the yellow alrm wires? Then its just a matter of reveresing them, which I actually think I tried and it still failed. I am thinking the green wire ought to be connected to one of my yellow alarm wires???

Hey my chiller isn’t cooling my water down.. would you say it needs re gassing?

Can you set the temp below 3c? I need to go below 3c. Can you set it 0c or go into the negitives? say -10c if needed? Also do you know what the chiller is made of? is it stainless steel or cooper internally?

do you know where i can find the full cw 5200 manual where it explains all these different parameters please

well done mate great video helps me heps here in aus

Do you have it in 24/7 or do you turn it on just when about to use the laser?

If the temperature in a country around 37° Celsius what is the correct temperature should be set in this case?

Perfetto e semplice, very good

thank you!

Thank you very much, I had to drag it back a few times but I think I have it set up based on some of my ambient "extremes". My machine is in the lower level of my residence so it should never get below 10 C (or above 30 C)

Thanks

any way to change this thing to read F instead of C?

thanks

Can you lower flow rate mine blew all the tubes off?!

My chiller button is not working plz help me what can I do

great instructions, but unfortunately my new chiller wont cool. compressor gets real hot and the outlet pipe running from the compressor to the condenser isn't even warm, nor is the pipe from compressor to water tank cold. either it has no gas or the compressor is a dud? either way its doing my head in trying to sort it and the seller is trying everything to get out of any responsibility they have.

thanks. super helpful. the printed manual was not a help and i was total out of mind.

Hi my cr-5200 when i turn it on it just displays PP how to fix it please?

Hey, have you stopped making videos? 🤔☹️

নাবার চাই আমার একা চিলার লাকবে

This is a knock off, not a genuine S&A CW-5200 chiller