Great job bro thank you

thanks. super helpful. the printed manual was not a help and i was total out of mind.

Super Helpful your video, very clear and straightforward. Thanks for your explanation.

well done mate great video helps me heps here in aus

Do you chamfer edges first before truing?

What laser machine did you use??

Great video! I needed to adjust mine to NOT chill during the winter when I have an aquarium heater in the tank.

If the temperature in a country around 37° Celsius what is the correct temperature should be set in this case?

Do you have it in 24/7 or do you turn it on just when about to use the laser?

Excellent video. Thank you.

My chiller button is not working plz help me what can I do

Router lift incra use spindle diametter 80mm?

I NEED HELP PLEASE 🙏 I HAVE THE AKJ1390H AND I'M TRYING TO FIGURE OUT THE PROPER PARAMETERS IT'S SUPPOSED TO CUT MEADOW AND I CAN'T GET IT TO WORK CUSTOMER SERVICE HAS BEEN TRYING TO HELP THROUGH PROCESS OF ELIMINATION BUT 3 MONTHS LATER I CAN'T GET IT TO WORK

I have a ajk1390h I'm having a problem with the software setup I'm not able to get the laser working can someone please give me any wisdom to help please

What did you use to engrave the pen? This was about turning, not about engraving. Thanks.

This is a knock off, not a genuine S&A CW-5200 chiller

very strong machine

I just found this video just in time. It's exactly what I need. I had a Vevor CW5000 delivered a few days ago for the DIY 60W laser cutter/engraver I just started to build. I read the instruction booklet briefly and was concerned that the default "intelligent" mode appears to set the temperature higher than I have been led to understand is ideal for the laser tube. It looks like it should be a breeze to set the chiller up correctly following this video. Thanks a lot.

Great video, what made you choose acctek out of interest compared to blue elephant or gweike for example? I had a quick look and they seem to be the two largest co2 makers on alibaba. Also Are you still offering help with getting a laser fitting your needs?

নাবার চাই আমার একা চিলার লাকবে

Do you have a build spec sheet that can be provided tp have them make a machine as you recomend? Thanks

Can you tell me about your experience with acctek? What about aftersale service? Are they responding to you?

Well done, thanks.

Hey there, would you be kind to offer some advice, any is very useful: I have a Robland Z400 M panel saw sliding machine with 2 blades. Problem is that i can't align them perfectly... The pre cutter is always a bit off to the right or to the left and that is my problem. How can I allign those 2 blades perfectly?

I don’t understand the value of the camera. I was excited to see the possibility of not having to make sure my plate was square or positioned perfectly each time I cut. Do I understand this right. I have to put it on then measure the offset to torch then make a mark outside the material at that offset then bullseye the camera to the mark. Do I have this right?

Hello have you had issues with returning home were the head keeps going

Light sandblasting and maybe in combination with application tape too would be my suggestion.

Laguna Fusion Table Saw 3hp 230V I did you see this and what do you think of it many thanks colin

I can’t even begin to thank you for this video. Without this I never would’ve figured this out.

do you know where i can find the full cw 5200 manual where it explains all these different parameters please

Cool video. Glad you are rehabbing this machine. I try to sometimes too but not always. Who makes that saw? Altendorf?

Hei thank you the information are great! In 2021 do you suggest again ACCTEK for laser? (i want a chinese laser)

Is this the standard model or did you have upgrades done for this spec?

Excelente!

Perfetto e semplice, very good

Very simple and clear explanation.

Thinking about similar setup for three router station. Questions: 1) why not water cooled for noise; 2) have you tried panel raising bits (e.g., 3+ inch bit with back cutter) on a single pass); 3) if you did it again what would you have changed?

Did you ever decide if you were going to distribute these stateside? Looking to purchase and I'm having issues getting ahold of someone in China.

Can you lower flow rate mine blew all the tubes off?!

do you remember which set of holes you used to mount the spindle in the lift? looks like E2 maybe?

Where I can get the crossbar filter for the camera?

how is it attached to the table?

Can you do another video with more info about the laser (brand/price range, etc.) and techniques on how to use it on pens and other wood objects? Thanks!

Very helpful. Thank you.

thank you!

I have a 2000 and I noticed the wheel was almost lopsided. I will try this at a slooow speed also, thank you. Didn't want to buy a new one if this all that's wrong. Thanks again.

Hello everyone, the laser machine power is RECI W6 130-150W,

Way to go! Great video and explanations. I just got my first Chinese machine and after a lot of research I made it a bit tailor made too. Buying straight from the manufacturer was the best thing I could’ve done, as u said, upgrades are way cheaper. I also made the same mistake to buy it CIF and here in Tallinn they charged me more than 600€ to receive it and do the paperwork... great advice of yours. Also, with all the upgrades, how come u didn’t upgrade to hybrid servo motors on the XY? Cheers

Can you set the temp below 3c? I need to go below 3c. Can you set it 0c or go into the negitives? say -10c if needed? Also do you know what the chiller is made of? is it stainless steel or cooper internally?

In 2007 had a forklift operator drop a slab of granite onto my Altendorf. took 2 days to get it back into alignment.