Good video, I like to give the o-ring a light coat of marine grease. It will come off much easier. I use the larger Yamaha filters, they'll fit the same base as that quicksilver. I always change them once a year, its cheap insurance.
@Skyhawk945 Жыл бұрын
No no, oil to lube gasket only.. Always change during fall winterization because any water in the filter could freeze and split the filter wide open and gas will end up in the bilge.
@matthill5066 Жыл бұрын
This is how NOT to change your filter. Pull up your dip stick and get a little bit of oil to put on the new filter. And ALWAYS prime the new filter with gas so that you don’t run the fuel pump dry. It will burn out and ruin the pump in seconds. I learned that lesson the hard way.
@miketworld Жыл бұрын
Thanks
@issalowbenzgarcia677611 ай бұрын
Hey man quick question when you say prime the new fuel filter you mean fill it up with gasoline right
@matthill506611 ай бұрын
@@issalowbenzgarcia6776 yes
@aliveinspaceАй бұрын
Yes @@issalowbenzgarcia6776
@martinschulz93817 ай бұрын
When I bought our boat and the salesman was running me through all the tips, he really emphasized the importance of changing this filter regularly. Good video, but fill the new filter with gas first.
@cdilljr Жыл бұрын
Whatever is in the top of the filter is the fuel. Water will be at the bottom. It’s heavier than gas. Easy to see on my diesel engine. Dirty water at bottom, pink fuel on top.
@userac-xpg2 жыл бұрын
would it be better to use a little motor oil on the seal instead of fuel? like an oil filter.. I'd be concerned the gasoline would dry out the seal.
@BigIslandMNMinnetonka2 жыл бұрын
Yes.it would be better
@paulinswfl82182 жыл бұрын
Just wondering why you didn't prime the filter? Is that engine fuel injected? I have a Ford 302 in my boat with a 2bbl Holly and I prime it. Works for me. Nice video!
@BigIslandMNMinnetonka2 жыл бұрын
Didn't want to prime. I was curious how it wouod act it I didn't. It didn't act up much
@ponchyah2517 Жыл бұрын
Nice Job!
@sean6049 Жыл бұрын
Hey Chris, I have a 3.0 Mercruiser that I used to take out all the time, it ran great. Last 2 years it's been sitting. I started it last year but ran rough. This year it won't start. Tank is 3/4 full. I haven't changed this filter in 8 years... i know very dumb.. Now im putting new spark plugs, cap and rotor, ignition coil, new plug wires. Also this new filter. Anything else you recommend to get this boat running again?
@BigIslandMNMinnetonka Жыл бұрын
I would do the impeller too
@sean6049 Жыл бұрын
@Chris Boats I did the Impeller about 3 years ago. Think it would need replacement?
@juju1896 Жыл бұрын
@@sean6049yes
@donnakelly5993 Жыл бұрын
Use oil on O ring not gas!
@daveengstrom9250 Жыл бұрын
Wow. Just wow.
@beer_money2 жыл бұрын
How many hours would you say you want to change this out? Different boat owners will put different amount of hours on their motors each year.
@BigIslandMNMinnetonka2 жыл бұрын
I recommend the beginning of every year which is most important. I wouod say 100 hours.
@Skyhawk945 Жыл бұрын
Every year during fall winterization. Any water in filter can freeze and cause filter to split/burst. Changing in fall is the safest way to insure it's water free..
@alexgussev53282 жыл бұрын
What to look for if rpm gauge not working
@dumpsterfire6351 Жыл бұрын
A new boat/hobby
@Fishingin290 Жыл бұрын
Hello, I just got a fuel water separator Quicksilver, and I noticed something rattling inside. Is that normal on these fuel separator filters? I’ve done plenty oil changes with never rattling, not sure fuel separator is different.
@aliveinspaceАй бұрын
No
@yektaahishali5436 Жыл бұрын
It is not water all that is you know that yeah? Only a few drops in it. Those filters work diffrently.
@richarddomsicz6702 жыл бұрын
way too tight
@kennyparrish315625 күн бұрын
Het dumb dumb read the directions on how to tighten the filters