Definitely made me feel confident about trying this myself
@SP-zg6lb Жыл бұрын
Good video, my only recommendation is replace the bushing & yoke also. As you could see the seal was already replaced, it went bad again because of a bad bushing/yoke/u joint, which cause vibrations.
@korndawggy1801 Жыл бұрын
Looked kinda like the rear differential had some leakage too. I was thinking one of the U-Joints might be bad or may have been at some point.
@david_kg Жыл бұрын
Man, I don’t know if I could have ignored how bad those u-joints looked. But overall great video on how to replace driveshaft seal.
@robertsmith863210 ай бұрын
I just did this on my Astro. The seal was original and tight against the transmission housing. To remove the seal, I used a good brand new chisel and hammer to VERY carefully to go around the seal flange and separate it without damaging the transmission. After that I hit the flange with a screw driver to deform it slightly at one point in the old seal for removal. Worked perfectly and in a couple minutes it came right out. No damage or marks on transmission housing. For installation of the new seal, one of the cups in my ball joint press fits perfectly over the new seal.
@chrisstrande5878 Жыл бұрын
Thank You Sir, Your video & wisdom is very knowledgeable!
@WrenchingWithKenny Жыл бұрын
You are most welcome. Keep wrenching 🔧
@witto638 ай бұрын
Thanks boss a Gare fix my truck tomorrow 👍👍👍
@uxkxowxloc34492 ай бұрын
Thank you so much I’m gonna do this in the weekend so Helpful 🙌🙌🙌🙌🙌
@reggie45242 ай бұрын
boss man you make it seem so easy i hope this will work fot my 94 impala SS
@WrenchingWithKenny2 ай бұрын
It will. You've got this. Let me know how your repair goes. Keep wrenching 🔧
@frankkennedy53618 ай бұрын
Good video without being overly wordy. Thank you.
@AG-dt5hy Жыл бұрын
Thank you for that video.
@bigal4304 Жыл бұрын
Keep them coming
@markfeuerherdt23389 ай бұрын
I have a 2001 GMC 1500. Had the output shaft seal replaced. It is still leaking where the tailshaft and the seal meet. Not leaking from the rubber boot. I noticed that in the video you put grease on the inside of the seal and sealant on the outside. My mechanic did not put any sealant. Would that cause the leak? It is only a tiny drop. What kind of grease did you use? Trying to find your seal prep video. Thanks.
@chicanoperez6377 Жыл бұрын
What did you pack the seal with sir?
@julioramos5737Ай бұрын
Great video
@olemulletgarage2637 Жыл бұрын
If the OG seals were not packed with grease then why pack the new one with grease?🤔
@elshowdelpape44454 ай бұрын
Thank you Sr👍🏼
@robertaccorsini4663Ай бұрын
The rust pattern on the yoke can cause them not to fit correctly in other positions
@southernslipping4225 Жыл бұрын
I have seen the tail shaft it self let fluid leak out yoke some have a air hole for when you push them in it let’s air out
@jpjohnbo2 жыл бұрын
Looks so easy...when you do it.
@WrenchingWithKenny2 жыл бұрын
Lol . Thanks !! Been doing this for years !! Thanks for watching !!
@project6productions924 Жыл бұрын
dont know if youll see this or not but i was wondering if there is an underlying issue because my rear diff is leaking a bit too and so is my tailshaft thanks in advance!
@WrenchingWithKenny Жыл бұрын
If the seals are constantly going bad, the tailshaft seal could be caused by either excess play from a worn tailshaft bushing or rust build up on the shafts yoke. Possibly even a worn yoke. The pinion seal in the rear axle could be from too little preload on the bearings or similarly , a rust or crud build up in the yoke that rides in the seal. I've on a rare occasion seen the yoke actually get a wear groove from the seal. Thanks for watching
@ericsearcy89392 ай бұрын
How much would you typically charge for this kind of job?
@kennywhitcomb15855 ай бұрын
What about the leaking pinion seal ?
@Papisartee7 ай бұрын
Was the trans already empty?
@josealonso65685 ай бұрын
What would be the cost of that seal replacement, you know from fair to high? TIA
@jaybutton3004 Жыл бұрын
I have a 92’ with a 91’ manual getrig HM290 transmission. Is it the same process?
@WrenchingWithKenny Жыл бұрын
Send a photo to the Facebook page Wrenching with Kenny with a description of the information you're looking for. I will have Kenny look at the page tonight. Thanks - Meg aka Mrs Wrenching
@retrobro671 Жыл бұрын
What grease did you use to pack the new seal?
@xpelon209x11 ай бұрын
What is the blue stuff? You packed the seal with. Thank you!
@WrenchingWithKenny11 ай бұрын
Transmission assembly gel. Thanks for watching 🔧
@luissonoma62556 ай бұрын
@@WrenchingWithKennyYou’re welcome.
@graytolbert6461 Жыл бұрын
what’s the part number?
@kentesinsky432711 ай бұрын
How much would you expect to pay at a local garage to do this job?
@luissonoma62556 ай бұрын
$80-$130 an hour.
@rickyallen2913 Жыл бұрын
What grease did he use ?
@Fish-dw5uw10 ай бұрын
Transmission assembly gel
@robertsalcido2028 Жыл бұрын
I need some help I have a 79 c10 and the tail shaft has play in it I think that’s ruining the seals. Is that play normal
@northrockboy7 ай бұрын
The shaft goes in about 1 inch then we feel resistence. Very strange. Seems to go in like that in 3-4 different locations on the driveshaft
@austinearl433 Жыл бұрын
Ahh yes, dont show the tool or how to use it. Thanks genius
@LJPMotorsports Жыл бұрын
What tool? The seal puller? If he doesn't use one, and doesn't like to use one, why the hell would he show it's use? He's showing you how HE does it. You wanna know how to use the puller, check the top of the KZfaq page. There's a search bar there. Type in "how to use a tailshaft seal puller". Genius.
@efrainchavezii5257 Жыл бұрын
Right? I sat through this video to see the install tool and how to use it. He showed EVERYTHING but that.
@Consider_it_done Жыл бұрын
Which seal did you use? And where did you get it?
@carportmods10 ай бұрын
For future comment readers. Auto parts stores. Year, make and model specific.