Kinda missed a trick the intake is outside so you are heating outside air if your intake was from the garage then as it warms so does the input air so less heat needed to warm up the air, it’s a closed circuit so no fumes as burner air is separated

Hi Adam me and my dad have run night heaters for years in our garages. What we learned especially in cold weather is best to have it low mounted and also have the intake plumbed inside also so it is more efficient

Had mine in the garage over 12 months now keeping the cossie warm and bikes great bit of kit

This is the most in depth video I've seen so far and it's pretty decent at explaining the history and use of these. I have one now that I put in a old military crate for mobility and i installed a quick disconnect so I can either use it in the car , with alligator clamps , or connect it to a 120v to 12v 10a wall adapter I got that's really simple

Been watching since you had like 500 subs. Your editing is getting better and better. Always look forward to your videos. Keep up the good work!

Great video Adam. I installed one of these in my garden shed years ago before I could fine any links on youtube. I worked it on the basis of running one on my boat. Best thing I ever did. I installed everything outside except the controller its been working a treat

Enjoyed your video. It was good to see the giblets of the machine. I liked the idea of the weatherproof metal box. Some comments, mainly repeating stuff from the comments below: - I can see why the hot air output was put high as you had an easier way into the garage via the soffit than coming in through the wall but the heat should be coming in low to give it some chance to heat something up in your garage before it all ends up in the roof space. - the input air to the heater should come in from the garage eg. from all the lovely warm air in your roof space as it will be more efficient to heat pre-heated air than the external cold air - you should have a fuel-filter between the fuel tank and the pump, especially as your fuel tank has its feed from the bottom of the tank which is where any crud from the fuel will settle - replacing the fuel line with a better quality fuel line is a good idea but the 5mm automotive fuel line is too big for the pump. It should be closer to the original ID of 2mm and be hard and not squishy like the original fuel line. The squishy fuel line allowed the manufacturer to have a simpler/cheaper connection as the line can be pushed on the fuel nipples. The hard 2mm ID can't be pushed on the fuel nipples but you can the use the 5mm automotive fuel line to create joiner pieces and attached everything using jubilee clips - it would be quieter if the fuel-pump was installed outside - it might be safer if the exhaust pipe that is inside the metal box was wrapped in some exhaust wrap - it is important to use a battery to run one these heaters as though you need 12V to start the machine and keep the machine running, more importantly, you need 12V to allow the machine to cool and shutdown properly. A 240V to 12V adapter wouldn't allow this cooling period if power was lost when the heater was running - it is important to bleed the fuel line to the pump before you start the system as these type of pumps are lubricated by the fuel they are pumping. The pumps are good at pumping but not so good at sucking and so rely on the gravity feed from the fuel tank to do most of the work. If there is air in the fuel line then the pump can spend many minutes trying to suck this air out of the line without any lubrication

Found ya channel the other month and binge watched most of them, top lad you are mate keep up the great vids 👍

2 points on your installation ‼️ First warm air rises, so in any warm air heating system you want the heat blowing in low down. Secondly you don't want the intake drawing air from outside, in winter that air is going to be colder. You want the intake drawing air from inside, that way as the garage warms up your recirculating warmer air, rather than trying to heat up very cold air from outside. It'll run way more efficiently and warmer that way. Oh and another thing, china and japan are completely different countries. Japan makes some quality gear, think Nikon, Honda etc China on the other hand, products tend to be cheaper for a reason ie lower quality, poor build and lower quality control.

'China is in Japan' made me wee! I've had a Chinese heater in my camper for 3 years and it's been faultless. The exhaust rotted after a winter so I fitted a Webasto pipe and silencer, exhaust is quieter too.

Ive installed a few of these Adam and i have a few of tips. Power supply could be a leisure battery fitted out of the way and charged via a motorbike charger which are very small and easily hidden, this way you can just turn it on when you like without faffing about opening bonnets and then every few days turn the charger on for a bit, I have mine setup this way with all the cabling in conduit and the control panel and charger mounted on the wall. I would also put a grommet around the fuel pipe going into the box as the pipe can move as the pump pulsates and it wont take long to cut the pipe on the metal entry point to the box. Lastly check your insurance with regards to a diesel fuel setup running an appliance as it could cause headaches in the event of a claim. Nice job fitting it in the box, i use mine in winter but usually put it on for an hour before i head out as they take a while to warm the space. Keep the videos rolling.

i just put on of these in my camper, thanks for the vid, feel more confident taking mine apart when needed now :)

Literally just finished watching your last video and I get surprised with another up load

Nice one fella, good insight I’m thinking of putting one in my van👍

I got a bar in my garage so we use the heater quite a bit. This is a great installation but move the heat intake into the the heated area and the pump outside. Lower the tank so it's easier to fuel. Also, try setting it to temp instead of Hertz for a garage.

Always make time to watch your videos mate keep them coming 👍

I use mine with red diesel, which is cheaper (in my country) . You can also mix it with waste oil (60/40) without any smoke or smell. Those heaters are awesome....

Hi Adam. If you don't have one already it might be worth installing a Carbon Monoxide and Fire Alarm. I have a combined unit in my garage.

Nice video, nice installation too. I have watched alooooot of dieselheater KZfaq clip, but this one I really enjoyed. Thank you.

I've been using the 5kw in my kitchen we got new for £100 4 years ago. I have it outside in a small cupboard I made with the air pipe through the stone wall into the kitchen of our large stone and lime house. The downstairs has large double doors between the kitchen and livingroom, so the heater is a first heat on a morning u til the log burner reaches temp. It's fantastic. The second year we had it in 2021 we had temps of -21°c but we were toasty. Only issue I had was last week the fan failed but £20 fix.

Very good video . Interesting to see the heater apart & how it works . Thank you

Fantastic video Adam 👏 very informative 👏

Nice one adz top install and well explained 👏 love the different content 👌

The SMPS (that you showed) are safe as houses mate. Just make sure it is a little bigger ( in amps) and fused properly. They also have internal safety features including a fuse and short circuit protection. It will need an enclosure like! Cool video!

Have one in my camper. Never let us down yet

Nice one. Also as previously mentioned get some red diesel as it's cheaper and perfectly legal to use in your heater so will be even more of a saving.

Nice one Adam thats what I like about your channel always something different i tell all my friends and family about you this is definitely a learning channel 👍.

Adam I’ve got a old parkway fire in my garage gets up to 35 degrees in the winter, keeps the old mk2 escort lovely and warm, keep up the vids mate.

Due to recent financial and personal difficulties I’ve recently brought and lived in a static caravan for around 5 months and the first thing I installed was a diesel heater, cost £100 from eBay and I’d be lying if I didn’t say it wasn’t worth the money…. Great video as always Adam, keep up the good work bro 👌🏻

Next week we see how the insurance claim for a burnt down garage is progressing 😂👍🏻

you should get a c02 alarm

i use one of these to supplement the heating in my house i run it on kerosene, it runs cleaner than diesel and is also cheaper i also drilled an extra hole for the air intake so the return air was warm air from the house and not from the cold air outside

Great idea on the box. Might do the same with mine.. also Love how you kept the “fuck sake” in. 😂

Te sigo de mucho tiempo y del primer video me dado cuenta que eres una persona con caracter y un corazon grande. Espero que no cambies nunca y que seas un exemplo para la sociedad.

I love the Cossis in the Back! Had 20 years ago a silver one 🥰🥰

Hi Adam. Keep up the great content. Loving watching your uploads all the way over in Sydney Australia. We get cold winters here also and am looking to fit a cheep heating system to my double garage. Now you have had yours installed for about 4 months how are you finding it? Seriously considering this system. Cheers mate!

I put one in our summer house. Similar job but used the 240 to 12v transformer. I run mine on jet fuel!

Just watched your video, good content and your explination is sound and detailed. Ive just watched cos ive nothing else to do. Ive had a few of these CDH and run 2 at the moment, one in my double garage/gym. Also one direct into my living room thats heating up 2 floors from 8 to 11 pm. Get yourself kero or red, save a penny or two. Best mix ive used for 2 years is 50/50 of each. Kero can be run on low settings and red very good for high. These are great bits of cheap kit that you know require periodical diy seevicing. Shame you went down the 70 quif box route, but if it works! Id rather save the 70 quid and make a. Box. Good luck with your channel. Be lucky

That's a really nice job you have done there mate. 👍

Whats really going to bake your noodle is when you realise you can buy these with a box

Hi have one in camper and on it it takes the air to be heated from inside the van so it’s not heating outside air will you heating a large area it would be a good idea to do the same so as your garage heats up the heater will be more efficient

Got one of these for my shed in October, great little heaters, much cheaper than leccy! The Chinese ones are based on the patent of the original German design, the patent ran out so it's a legal copy. They are easy to disassemble, repair and reassemble.

Not sure I need one here in Australia, but I enjoyed watching you fit it

You need pipe extending to floor level hot air rises so your heating the roof space first first.

i think the other comments are right, pipe the air inlet to inside the garage, my mate's used to pull damp into his garage, that's probably why hot air rises, so you should have the hot air piped in it low down i'll keep an ear out on newcastle rd, fingers crossed every time i hear a fire engine...

Ask Paul Nicely if you can kindly have the oil back from ya sump which he drained last week then you can run it for free 😂,good video fella 👍

During start and warm up these heaters draw around 30-40 amps so that 8-12amp wire that you used is actually more of a fire hazard than the psu's that you said aree a bit scratchy. I've had mine connected to my cdh for over two years now without any issues at all. Just like any other electrical unit I tune it off and unplug it when it's not in use.

Nice video thanks, do you have a link to the fuel tank you mounted on the wall, please.

I'd looked at these myself they look OK mate thanks for the video. I'd put a carbon monoxide tester in the garage though just incase 👍👍

Good man for giving anythink a go,but I couldn’t be doing with that pump going all day would do my head in.

I would use a separate battery connected to a solar panel to trickle charge the battery. Fuse the connection between battery and heater, mount the filter in the internal wall so the air is warmer and more efficient. The output warm air pipe extend to floor level. Buy a Carbon monoxide detector and a fire extinguishers.

I'm getting one of these for my garage 🤙

I would recommend fitting a grommet where the fuel line passes through the enclosure.

A space that size you looks like you could do with a couple of these, or just route more piping around then garage to heat it evenly

We are getting similar heaters for our new vans, whenever they decide to arrive 😂. Might offer to fit them after watching this 😊

Very helpful. Thank you for the video

Hi adam, just wondering if you ever fancied reviewing a 380hp fiesta st (dynod), running cams, hpfp, big turbo and all the other supporting mods with abit more.

I was watching one of your videos the other day and i thought I heard one lol

My ocd driving me mad. Pull your insulation tape as you wrap it round. It heats the tape up and makes it stick better and looks better. Great video tho. One of the best I’ve seen

Adam, no links in the description? I'm interested in that exterior housing box mate

How is the working now? Does it warm that garage space well enough after this amount of time?

You should mount the air intake (not the burner, the heater input) indoors for more efficiency and also, right now your setup can bring in exhaust fumes if winds favor it.

I think I be having big fire extinguishers hand and carbon monoxide alarm as well 😊

Bro the air intake should be coming out of the garage, like a loop so it can build up the air temperature.. if you don’t like the noise you can use a silencer ..( those hemp carbon filters work great 😊) oh I have seen some videos of running that exhaust pipe true a thank whit sand , creating a sand battery.. 💪

Well done! Where are you located? Low temp in Winter?

Good job your jacket hasn’t gone up in flames 🥵🥵🥵

I had one of these fitted into an external housing. The biggest faf was picking up diesel supplies every few days. I would buy a central heating tank

Thank you!

I’d of put the air intake inside , in the box outside seems like it could possibly blow exhaust fumes inside, I would definitely put a carbon monoxide alarm in there mate

Nice motors mate 👍👍

Could you use green diesel / agricultural fuel

I only watched to see those Motors! 😍 However, my new heater worked fine first time i used it, had it on for few hours, all good. Now when i turn it on, gets all warmed up, lasts about 5 mins then i get a E10 code, "Heater over Temperature" any idea what that is?

You could use a ceilings fan to circulate warm throughout room

Nice video that box is weatherproof but I guarantee when you open it in a few months it's full of fucking spiders still 🤣

‘Let’s put a little in, bla bla leaks’ and you emptied your jerrycan. 😂

Handy to have spare gaskets set & glowplug, maybe a spare burner chamber if it really gets blocked up 👍

Tidy work there adam

You should really put them inside biasicley the inlet air will be less work for the heater so your recirculating the airflow but put the exhaust outside this is how they are fitted in trucks

@18.10 "this is a Chinese heater, and China is in Japan and the quality isn't the highest" you sure about that Adam??? 🙂

Adam, was the pump on the wrong way to start with... bet you had fun diagnosing that if so 😃

Love it Adam the way u just pull bits apart then re build them with all your tch talk like jiblets so amazing & that pump sounds like my bed on a Saturday night 🌙 👍 just love your videos mate top draw 👍

Adam another stonker brilliant great content & brilliant channel

Great job but at 14 minutes surely you got the pump running the wrong way?

what I done was instead of sucking cold air through the heater ..I have recirculated the air in the room through the heater does that make sense..the cold air is being sucked from inside the garage and blown back in the garage

Love those cars you have.

Heat my house with one been running daily for 3 months now, never fails to start

Adam get the air intake taken from inside the garage. Recirculate the air will make it much warmer. Not the combistion inlet pal leave all that outside.

You could do with a heat gun to check the heat of the cables... I wouldn't advise leaving any battery connected to the car while using the heater look at a leisure battery

Hi Adam, cool video, why don't you try some red diesel.

its more usefull if you place it low ? ...so the cool air that sits low heats up faster in an more even way ...

Try using two ford transit egr valves on the exhaust to give you hot water from waste exhaust heat

I did wonder if you was going to mention this heater adam I've heard it ticking away in the background a couple of videos ago 🙂 like the look of them but I hate Diesel i wouldn't want to spill it on my slabs anywhere.

You should mount inside with the exhaust exiting to outside, that way you get the heat from the exhaust and the warmer air inside being used, so temp is higher 🤔

Nice Ford :). I thought you were going to put the noisy pump outside?

Need too run that wiring though some kinda grommet

Great Idea Fella' Tom in Ayr.

It's nice to hear a local accent in a KZfaq video 🙂

Be careful with running off your car batteries Adam, I have made a similar mistake with led lights in my council garage without power. A car battery is designed as a fast discharge,fast charge so as the diesel heater initially uses a few amps on startup and then drops right down during running, so is a low draw so won’t do your car battery much good, especially as you aren’t using your cars everyday. You would be better using a leisure battery as they are designed differently and are better suited to a low draw and I would have a battery charger but also for added cheaper running invest in a solar panel and solar charger. I plan on getting a diesel heater and a camping powerbank to run it and led lights, and be cheeky and charge the powerbank at work😂😂😂. However it would be cheaper to do leisure battery and solar panel but I worry about the panel getting nicked as it’s a council garage away from home

For a more efficient heating connect the air input to the garage, not only air output.

Can’t you remove the glow plug without removing the diesel heater from where it’s been installed? I’ve done just that. It’s stuck to the floor of my van.