Citroën C3 Picasso Front Wheel Bearing Replacement
Рет қаралды 7,310
Жыл бұрынToday we will be replacing the front wheel bearing on this Citroën C3 Picasso 1.6 HDi!
@colinsmith7233 2 ай бұрын
Great video. Just what I needed to see. My C3 is about as rusted up as yours. Finished the job today on my car, I think it would not have gone so well if I had not see your video. Many thanks for posting it..
@maxautouk 24 күн бұрын
Glad it helped !
@chemistry636 Жыл бұрын
Good visual video. I like videos like this where issues are shown, then solutions enacted and if necessary adjusted again. A confidence video for anyone wishing to tackle it themselves.
@maxautouk Жыл бұрын
Thanks for the kind words 😄
@iqb62 5 ай бұрын
Thank you for this video. Good work.
@maxautouk 5 ай бұрын
Thanks for the comment!!
@aaronmachon9127 9 ай бұрын
Very informative. Always good to have informative videos like this that show you what to do also..😊
@maxautouk 9 ай бұрын
Thanks very much for the comment glad it helped!!
@aaronmachon9127 9 ай бұрын
Very welcome mate. Same car so just glad you never missed anything
@MarekMalevic Ай бұрын
Thank you for a very helpful video. IMO it makes no sense to try normal Torx in this case. I have damaged one and then bought torx for impact wrench. And that one worked very well.
@maxautouk Ай бұрын
They are crazy tight too!
@xerejuneseve6333 7 ай бұрын
Is it worth to buy this c3 for 500$ with bad front bearings?.The model from 2002 and diesel 1,4V -270 000km.
@maxautouk 7 ай бұрын
The diesel 1.4 is a horrific engine but if everything is healthy with the engine then just wheel bearings would be fine for that price
@wodzimierzknapik6741 5 ай бұрын
Great movie. But... You should clean rust on the nuckle arm firts...
@maxautouk 5 ай бұрын
The knuckle arm?
@wodzimierzknapik6741 5 ай бұрын
@@maxautouk Steering Knuckle
@maxautouk 5 ай бұрын
@wodzimierzknapik6741 what would cleaning off the rust achieve?
@wodzimierzknapik6741 5 ай бұрын
@@maxautouk Bearings don't like dirt. We see a lot of dirt and rust during assembly.
@maxautouk 5 ай бұрын
@wodzimierzknapik6741 the inside bore was very clean and both sides of the bearing have seals to keep debris out - where i live rust like this is normal and this bearing has been totally fine! ☺️ also dont forget the flange and driveshaft are not fittwd water tight to the bearing so they are open to the elements constantly
@mazdaman1286 8 ай бұрын
with torx always buy 2 . citroen 100 nm plus rust honda 55 nm some manufacturers go overboad on torq specs.
@maxautouk 8 ай бұрын
I think the torque isn’t too bad but yeah you’re right about the rust it’s a nightmare sometimes!
autodoc.co.uk
Рет қаралды 50 М.
Auto Manual
Рет қаралды 20 М.
Ситроен С4, Пежо 308. Ремонт Владимир Немченко
Рет қаралды 45 М.
Piggy Power
Рет қаралды 3,3 М.
Michelo D.I.Y.
Рет қаралды 20 М.
To The Garage
Рет қаралды 20 М.
SetrispossBoss
Рет қаралды 440 М.