4Runner is getting the job done--and then some. Be careful! The Kubota saved the day though!!

Jordan that was turffic job some I had doubts on but you did it and and some with the truck thank you for sharing and your time you got to find out why the lug nuts are coming off the left front not good

Well according to KZfaq you've made it to 10,000 congratulations young man👍👏. Gary 🇬🇧🇬🇧

Oh Jordan!!! God spared you son. If a log had slipped, you could have been trapped or worse swept under the bridge and drowned.... PLEASE PLEASE TAKE A "HELPER" ALONG WITH YOU IN CASE YOU SHOULD RUN INTO A DANGEROUS SITUATION. PRAYERS.

Blue lock tite would probably help your wheel from loosening.

10K...Yea!🎯💯👍💪...Go Jordan! Be safe man!

If you have a torch blow a hole in the end of each fork then use a plow clevis...works great. Then the chain won’t slide on the forks

Looks like soon the bridge is going to turn into a dock. Be safe.

Nice job, it does look like fun! Congrats on 10,000!

Jordan congratulations on 10 k , thanks for your videos.

You are going to have to do some work on that bridge this summer!

Congratulations on 10k subs.1👍👍👍

You need a hole in the end of the fork to put a clevis on to hook the chain to.

Nice video. I have a L4060 HSTC coming in about a week, the wheel studs may be something to keep an eye on. Enjoying your videos and subscribing. Keep up the great content!

👍🤗

you need to get a backhoe for your tractor or maybe a small cheap excavator , will do the job in no time

I use a chain saw on my problem like yours, it just floats away..And my problem becomes somebody’s problem down stream. Yeah , a note after several episodes of this, I don’t cut some of the big ones completely into, the pressure of the water ,next time will break them and have seen the whole jam float away in two piles. Be very careful the danger is unpredictable and good luck!

Free fire wood

Great job. Great video. Thank you. 👍

Quite a project, you're lucky to have a grapple....my Kubota is too old for attachments like that. I have that same extractor set and it never occurred to me to use it on studs, just rounded nuts.

WHAT A MESS TO CLEAN UP. GOOD JOB, KEEP SAFE

Hey Jordan good video I like all your videos and I am a outdoor guy I do enjoy your videos on fixing your cars and Toyota but was good to take a break and get back to your outside work. I am sitting up here in Wisconsin with a foot and half of snow so not much to do with my kubota L4060 except to move some snow and that isnt the best with kubota I definitely need chains on tires way to much slipping and sliding without them

Look at the bright side free firewood

I am scared for you at those last few minutes as that end of the bridge looks sketchy.

10.3k!

You should be a little safer on some of that, the jerking out.of the river with the 4runner is a prime example. If that cable would have snapped down close to the tree, the rest may have come rifling out and beheaded you. It would have been much safer to attach your winch on the tractor and pull them up where you were. I know it's not my problem, but I enjoy your program and want you to be alive to do it.

Hydraulics are a wonderful thing.

Will you do anything with the bridge? Fix the road over?

Nice work Jordan. What did you torque the nuts down to on your wheel? Have a good day.

Jordan, I noticed some of the log debris had saw-cut butts --- Who would allow such lengthy timber to remain near a flowing stream ? -- Don't your neighbors have any "down stream environment" scruples ? Stay Safe !

The right end of the bridge looks like it’s ready to fall in. The support has been washed away, are you going to redo that section of the bridge?

Cut the logs in half

I think you need a excavator for that job

Blue Lok tite