This is probably the route i will have to go for my projects i dont want to spend alot of money on them but i want to make it look legit this is definitely the way even tho its going to take a little more effort to make it happen good work bro and personally id stop the flake on the clear its too risky to match incase of a mistake i feel rather use base istelf but other then that dope work bro
@vanni_doestv451611 ай бұрын
Yea. The flake is risky. Fortunately it wasn't to big of a difference.. with proper lighting and everything being next to each other, it can be executed well... I'm doing a candy black over black rustoleum. Should be spraying this week. This is as budget as it can get all while looking great still. I'm hoping the candy black gives it an intense depth to it. On top of it already being clear over gloss black. I will be doing a flow coat as well. I'll post a video soon after
@trentdawg28324 ай бұрын
Nice job big homie!!!
@BearBudgetTurbine6 ай бұрын
I don't pay much attention to all those settings. Everyone sprays different. Everyones compressor is different. Settings for a real Dv 1 do not translate to something Chinese that just looks like a Dv 1 but is actually a different paint gun. Paper on the wall. A hand held light. Test😢 sprayouts before painting. Doesn't even matter if the settings match what others use or what the Chinese instructions say. All that matters is results👍
@vanni_doestv45166 ай бұрын
I completely agree. Although with this gun and my fake gti. I found that spraying closest to the recommended settings got me the best results. But other guns I've had to find my own settings.. I like to use stated settings as a starting point on every gun and adjust from there
@duenas1988 Жыл бұрын
🔥🔥🔥
@henrylima6974 Жыл бұрын
Good job
@vanni_doestv4516 Жыл бұрын
Thank you!!
@duenas1988 Жыл бұрын
That's bad ass
@vanni_doestv4516 Жыл бұрын
Thank you broo🙏🙏
@duenas1988 Жыл бұрын
👏👏👏
@jacobydavis3953 Жыл бұрын
Might have missed it, but what gal compressor did you use? I have a spray it and plan to use a 20 gal and a n inflatable spray booth. But my compressor will be at least 30 feet from my booth so I was thinking about a 26 gal
@vanni_doestv4516 Жыл бұрын
I used a 60 gallon. But I'm sure you'll be fine with a 20g. If anything might spray a Bit slower.. but in all honesty if u run that at 30 psi like others say to.. it sprays the same amount of over spray as an hvlp.. so I sprayed at low psi and calibrated my fluid feed to it.. sprayed a bit slower but worth it. Way less over spray
@HowtoRestoreHeadlights11 ай бұрын
Are those from a Hyundai or maybe Vw Gti
@lssleepers646410 ай бұрын
What did use to cut and buff it with the little buffer u had used in the video/how did u make ur paint booth
@vanni_doestv451610 ай бұрын
I belive that was a 2 or 3 inch cutting pad, used with a mini buffer. Hooks up to the compressor. I got the mini buffer at harbor freight. And the pads I bought from a detail shop in town.. but surely u can find some on amazon.
@vanni_doestv451610 ай бұрын
The booth I used was a gorillas pro inflatable booth. U can check out when I first unboxed it on my older videos
@Rocket-hb6jh11 ай бұрын
Oxidised not oxidated
@dano74808 ай бұрын
Do you have to wait days before clear coat after putting on single stage?
@vanni_doestv45168 ай бұрын
If you're going to sand it like I did in this video. You can wait over night and scuff the next morning. Domt have to wait longer. Or you can simply spray wet clear over wet single stage. Just check the tds foe the re coat window
@dano74808 ай бұрын
@vanni_doestv4516 Thanks for your advice! I purchased Acrylic Enamel gloss black single stage and it says ready to spray but if using a hardener it 8 to 1. It's in the 30's-40's where I'm at right now but obviously painting in a heated garage. What's your thoughts on the hardener? I'm painting my sister motorcycle so it plastic farings. I'm doing all the plastic prep even primer/sealer because I know plastic flexes plus don't want the paint to flake off. Thanks again for your time and info!
@notchcoupeful9 ай бұрын
What's the spray gun u used? Model number or were can I find it..?
@vanni_doestv45169 ай бұрын
I think I used 3 different ones.. the "spray it r500" I beleive I used Majority of the time.
@vanni_doestv45169 ай бұрын
Can fins it on amazon
@notchcoupeful9 ай бұрын
@vanni_doestv4516 ok great thanks!
@scottferguson19324 ай бұрын
I was hoping you were actually going to shoot clear over single stage paint so I could know how that looks. Adding colors/flakes to the clear made this video useless for me. Your project looked good in the end, though.
@vanni_doestv45164 ай бұрын
I have another video where I paint clear over single stage. It's in my channel.
@paulcasarez40410 ай бұрын
I always mix clear into the gallon of single stage never over single stage