Clutch Replacement VFR400

No video

Clutch Replacement VFR400

Рет қаралды 35,870

Күн бұрын

An instructional video for how to replace the clutch friction plates on a 1989 VFR400
any comments or revisions you think i should add, just sent me a message

Пікірлер: 24

@ParaglidingChronicles 5 жыл бұрын

thanks for the upload mate, it helped me with my vfr 400 nc30 in Islamabad, Pakistan !!

@RG-ky9qs 5 жыл бұрын

Thank you very much friend from Spain has been a great help, I did not know where to start

@dar5150 14 жыл бұрын

Great vid, was putting this job off for ages. Will definitly give it a go now. Cheers

@oscarcovfr 14 жыл бұрын

Exelente tutorial..!!! muy instructivo..gracias..!!!

@WW2Adinfinitum 12 жыл бұрын

excellent job chief !! greetings from carrickfergus :)

@D_Egan_Flatline 14 жыл бұрын

@gycionas16 it depends what part of the bike you look at. the tank is the original colour scheme which is OEM NC30 the actual bodywork is OEM NC30 with NC35 colour scheme

@saltysealion 4 жыл бұрын

Nice job

@D_Egan_Flatline 13 жыл бұрын

with this clutch there are no traditional springs. it has diaphragm springs which are the large washer shaped.

@AcidVFR400R 14 жыл бұрын

great guide declan !!!! dont suppose you have one for rebuilding an Nc30 engine :(

@D_Egan_Flatline 14 жыл бұрын

@Wheeeeelie that is a proper honda tool, think it was about £25

@RedshiftSG 13 жыл бұрын

does it matter which way the engine plates go in ? I've noticed that the one side is rounded @ the edge and the other side not.

@mwoodford87 13 жыл бұрын

are the main clutch springs behind that clutch basket that the plates sit in? does it just pull off? many thanks

@D_Egan_Flatline 14 жыл бұрын

@AcidVFR400R nope, i haven't been that unfortunate yet. perhaps in time

@thewarlord3977 6 жыл бұрын

Great video, If my clutch lever is biting right out, and getting it into gear is a right clunk, and to get it out of gear into Neutral needs revs, would you say this can all be adjusted in the cable? Or is it likely my clutch plates need replacing?

@D_Egan_Flatline 6 жыл бұрын

If it needs a rev to come out of 1st into neutral, I would say don’t worry about it, it’s the nature of the bike and the age of it. The clunk into gear is chareristic of the bike, being a single sided swing arm, it’s more noticeable and defo more noteicablw if you have rode bikes from more recent years

@D_Egan_Flatline 6 жыл бұрын

As for the bite being right out, I would say do the plates. Yiu would be very surprised just a mill of wear would make to the feel.

@thewarlord3977 6 жыл бұрын

Hey, cheers for the quick reply, yeah all my other bikes don't do that, and had the bike for many years, its always done it, just wondered if I could make it a bit nicer, reckon the clutch hasn't been done in all the years ive owned it :-) so thats 20 years then, I reckon its paid its due.... :-)

@D_Egan_Flatline 13 жыл бұрын

rounded edge facing inwards

@saltysealion 4 жыл бұрын

Can you do one for valves

@D_Egan_Flatline 4 жыл бұрын

that bike is now a distant memory, i sold it about 4 years ago - i made this over a decade ago - sounds crazy when i say it like that