CNC Router and Plasma Cutter

CNC Router and Plasma Cutter | Overview I

Рет қаралды 6,471

5 жыл бұрын

This is a short overview about my machine.
Part 1: • CNC Router and Plasma ...
Part 2: • CNC Router and Plasma ...
Part 3: • CNC Router and Plasma ...
Part 4: • CNC Router and Plasma ...
Part 5: • CNC Router and Plasma ...
Part 6: • CNC Router and Plasma ...
Part 7: • CNC Router and Plasma ...
Part 8: • CNC Router and Plasma ...
Parts that I have used:
Electronic Set: tinyurl.com/y2hh4v7b
Racks: tinyurl.com/y82wbghh
Pinion: tinyurl.com/yxf45xdk
Linear Rails: tinyurl.com/yyn6k5x2
Cabinet: tinyurl.com/y6osu8ur
Plugs: tinyurl.com/y4rgqte5

Пікірлер: 39

@countryhandyman1064 5 жыл бұрын

Super Nice Sam. I loved watching this build. Good job.

@samsworkshopdiary5748 5 жыл бұрын

Thank You!

@sknaik6749 4 жыл бұрын

Hello Sam... Thank you so much for this amazing project,..your skill is really appreciated. 🙏❤

@samsworkshopdiary5748 4 жыл бұрын

Thank You!

@engamjd1722 4 жыл бұрын

great job 🌷🌷

@samsworkshopdiary5748 4 жыл бұрын

Thank You!

@bsw6583 3 жыл бұрын

Excellent job. What is this arduino board? Usb to lpt converter? Can you share connections diagram?

@Eartola44 3 жыл бұрын

Good video. Did you buy a normal plasma cutter and get the special vertical torch afterwards? If so, was it a difficult job wiring it properly? Thanks.

@samsworkshopdiary5748 3 жыл бұрын

Hi, yes I bought a normal plasma cutter. It was not difficult to change the torch. Most connections are screwed, only the pilot arc wire had to be soldered.

@QUERBEET-DIES-UND-DAS 5 жыл бұрын

I was here! 🙂🖐

@SimspaceDIY 4 жыл бұрын

Sam, great job on this project! I watched the entire playlist. What plasma cutter did you use?

@samsworkshopdiary5748 4 жыл бұрын

Thank You! I'm using a Stahlwerk CUT 70.

@SimspaceDIY 4 жыл бұрын

@@samsworkshopdiary5748 Thanks for the reply Sam. My mistake, what I really meant to ask was, what torch are you using? It looks like it's designed for a CNC instead of hand-held.

@samsworkshopdiary5748 4 жыл бұрын

@@SimspaceDIY It's a CNC torch also from Stahlwerk I think it will fit to many plasma cutters.

@DereksWorkshopAndProjects 5 жыл бұрын

Pretty impressive. Did you buy this in a kit or was it entirely assembled by pieces and parts?

@samsworkshopdiary5748 5 жыл бұрын

Thank You Derek. It wasn't a kit. I had bought only most of the electronic parts in a kit to save a bit money.

@DereksWorkshopAndProjects 5 жыл бұрын

Sam's Workshop Diary well it works good it looks like. I assume if it can cut circles that perfect you must be fairly happy with it!

@samsworkshopdiary5748 5 жыл бұрын

@@DereksWorkshopAndProjects Oh yes, now it's very easy to get complicated shapes out of metal. It saves a lot of time.

@SKern-yz3ko 4 жыл бұрын

Echt eine sehr gute Videoreihe. Ich frage mich nur, welches Programm nutzt du für das Plasmaschneiden, auch Estlcam? Gruß :)

@samsworkshopdiary5748 4 жыл бұрын

Danke Seppi! Ja ich nutze auch fürs Plasmaschneiden Estlcam.

@rajeshvidyarthi8728 2 жыл бұрын

Is yhe rail shaft 25mm?

@maxschroeder7580 3 жыл бұрын

Hey Sam, Was für Module haben deine Zahnstangen und wie viele Zähne haben deine Zahnräder. Ich habe grade ein ähnliches Projekt. Sehr interessante Videos!

@samsworkshopdiary5748 3 жыл бұрын

Entschuldige die späte Antwort. Die Zahnstangen und Räder haben Modul 1 und die Räder 15 Zähne.

@rajeshvidyarthi8728 2 жыл бұрын

What is the shaft diameter?

@Hoiinz 3 жыл бұрын

Hi Sam, ich baue auch gerade einen CNC Plasma und bin fertig mit der Mechanik. Jetzt gehts an die Elektrik.. Wie hast du den Plasma mit der Steuerung verbunden und benutzt du einen THC? Hast du vielleicht einen Schaltplan oder ein Video wie du den Plasma mit der Steuerung verbindest? Danke!

@samsworkshopdiary5748 3 жыл бұрын

Hi, ich habe den Plasmaschneider an den Anschluss zum Schalten des Fräsmotors angeschlossen. Deine Steuerplatine sollte auch so einen Anschluss haben. Je nachdem wie dieser ausgeführt ist, musst du noch ein Relais dazwischen setzen. Am Plasmaschneider benutzt du den Anschluss an den der Taster vom Brennerkopf geht. Einen THC benutze ich nicht. Wenn du möchtest kannst du mir bei Instagram Bilder deiner Platine/Schaltplänen schicken, dann guck ich mal drüber.