Co2 Laser Power Problems and Trouble Shooting

No video

Co2 Laser Power Problems and Trouble Shooting

Рет қаралды 43,469

2 жыл бұрын

COMMON PROBLEMS OF CO2 LASER POWER AND TROUBLE SHOOTING
CO2 laser machine is widely applied into laser engraving and cutting. It mainly consists of luminous system, motion system and control system. Today, we introduce the judgment and elimination of CO2 laser power problems.
1. Laser head does not emit light when working
First situation, check whether the laser tube itself emits light (examine it in the laser tube light outlet). If the light is normally emitted normally, check whether the lens is damaged and the optical path is deflected.
Second situation, the light outlet of the laser tube has no light, check whether the water circulation is normal (see if the water flow of the pipe is smooth).
Third situation, water circulation is normal, check whether the laser power indicator is on and the fan is rotating. If the light is off, the fan does not rotate, first check whether the AC input 220V or 110V is normal.
Fourth situation, when the laser power supply 220V or 110V AC input is normal, first unplug the 6-wire green control line terminal on the laser power supply, and press "TEST" to manually emit light.
❶ If it can emit light normally, it means that the laser tube and power supply are normal. The problem is on the control line. Plug in the 6-wire green terminal control line and short-circuit the WP and G. If it emits light, it means that the water protection switch is broken; if it does not emit light, then short-circuit TL and G to see if there is light.
❷ If the light cannot be emitted or the light is weak, it means that the laser power supply or the laser tube is broken. If there is a reserved laser power supply, or a dual-head machine, or more than 2 laser machines, you can replace the normal laser power supply to rule out whether it is a laser power supply problem.
It is very important to reserve a laser power supply. If the problem appears, it does not affect production, and is convenient to find and troubleshoot.
Note: If the above problems do not exist, please contact our company for after-sales consultation and treatment. I hope this has been an informative video, If you would like to ask me a question about your machine, email askmatt@mwlaser.com.au If I don’t know the answer I will do my best to find the solution for you and it may be featured in a future Video.
NOTE: This is not a paid production or advertisement.
Show your support for MW Laser by Buying Matt a Coffee.
This can be done via our website www.buymeacoff...
Thanks for Visiting.
Until next time, take care
Cheers Matthew
Visit Matt's Workshop at MW Laser www.mwlaser.co...
Email: askmatt@mwlaser.com.au

Пікірлер: 68

@FredrikSvensson1979 Ай бұрын

I can't tell you how much this video helped me. I am in very stressful part of my life at the moment and every new bump on the road feels like too much to handle. You had me back up and running in no time with this and and my stres for the day is gone. Thank you.

@BrilliantDesignOnline 2 жыл бұрын

Matt- your videos are SUPER informative (sad Ruida and Cloudray don't have this content), but suggestion: use a lapel mic, rather than the built in camera mic. 90w DIY 6090 build here under construction in Montana, USA; thank you VERY much for your content.

@MWLaser 2 жыл бұрын

Thanks

@user-pp1wb9ps8d 2 ай бұрын

Awesome Video! The company i work for bought a used 150w 5' x 10' laser that wouldn't fire. after watching your video I traced the issue to the machine not having a water sensor. The wire for it was just coiled up under the machine.

@ajibadesamuel4578 11 ай бұрын

Hi Matthew, Thanks for this CO2 troubleshooting video. It is really informative.

@ralucutzarusuu1 9 ай бұрын

Thank you so so much for this!!!!! It helped me a lot with my laser.

@SridhanyaSmartService Жыл бұрын

AFTER SEE YOUR VIDEO IAM EXPERT IN LASER NICE WORK KEEP IT UP DEAR🥰👌🤝

@MWLaser Жыл бұрын

Thanks, I appreciate the feedback

@jbrondos 2 жыл бұрын

What about the readout on Cloudray MYJG-100 power supply? Can one press the TEST button and make adjustments using the little potentiometer on the side? If so, what number would be ideal to have in the LED display? 24 -- as is shown in Cloudray's product information pictures?

@robinsonmugerwa 5 ай бұрын

Thanks the short circuit helped out alot

@jbjb661 2 ай бұрын

what did he mean exactly by "short circuit"?

@shawnlandry1636 Жыл бұрын

Matt I am running into an issue on my 300watt machine where it cuts fine but after it has been running for 30 minutes there is something dropping the power because it stops cutting fully through the material any ideas?

@fritziesuggs Ай бұрын

I bought new laser tube, it's firing nicely but will not cut or engrave. I did a line test, at 85% power, the mA does not even go up past 7. What could be wrong?

@toodulpufsahrens3395 Жыл бұрын

What dose it mean if when u short circuit p and g it does nothing but when u short circuit l and g you get the laser

@MWLaser Жыл бұрын

Short circuit on P & G if for water protection. G & I will be laser On constant - not good

@Mekaproyects 2 жыл бұрын

Great tips Matt 😄

@MWLaser 2 жыл бұрын

Thanks! 😀

@ruipedro7691 Жыл бұрын

So, if when shorted L and G the laser fires, what's the problem? Psu?

@Cooke245 3 ай бұрын

Did you figure out the problem ? My laser is doing the same

@defaltoption 6 ай бұрын

my laser seems to start and then fade out over a 400mm length. what would cause this

@augiewhiteman8947 2 жыл бұрын

I purchased a Red and Black 80w. According to info on the machine it is practically brand new. Apparently the previous owner attempted to manipulate factory settings. Being new to it all, I don’t know how to return it to factory settings. Is there anyone that will video chat to troubleshoot or is it best to just purchase a new computer board? Thank you.

@donsll 2 жыл бұрын

If you are in Australia do I need to do this upside down????

@Jcorellis88 2 жыл бұрын

So am I correct in understanding if TEST button fires laser while P and G are shorted out the issue is the flow switch?

@natashaapplebyrahim2065 2 жыл бұрын

Hiya, Did you solve this problem? I'm a Newby and I don't know what it means to short circuit. Not getting much info that's helpful online. I am at the stage of checking to see if its the water sensor supply for my non firing laser issue. 😔

@robotronik6968 Жыл бұрын

Hi friend, well my problem is that miliamper (mA) decrease little by little while the CNC is working, the power supply is new, (I bought another one thinking the power supply has broken, but not), in one hour of working the milliamperes drecress from 21mA to 15mA. the AC supplier has 210v contact, (is low but, I always work with this voltage without problem) the Laser Tube is not new but not old, mmm apron I changed this apron. 1 year whit very low use. In advance, thanks a lot.

@raeesakhan8951 6 ай бұрын

Hi, my laser is firing a lot whilst cutting and not cutting completely through the acrylic and other stuff that I’m cutting, what could be the problem?

@ekobudianto314 2 жыл бұрын

I have a problem with my 100W Co2 laser. If my laser power is set above 50% (up to 99.9 %), the ignition of the laser tube is normal, the laser current indicator shows the number 15mA to 30mA. I can use a laser for the acrylic cutting process. But if my laser power is set below 50%, the laser tube ignition still has ignition. It's just not continuous (intermittent) and the current indicator shows a number below 1mA. So that I can not do the engraving process. Maybe someone can help provide a solution to my problem?

@tizianaberjaoui3274 Жыл бұрын

Thanks for the great Video, thumbs up. my laser is cutting but not engraving. I have a 644xs and use lightburn. The ruida controller pad only shows the vector cuts not the engraving. Can you please help me, much appreciated

@MWLaser Жыл бұрын

you may consider a support call, email askmatt@mwlaser.com.au to arrange this

@checkshirtjoinery5372 Жыл бұрын

or its the 24v supply, if you are having issues like power on controller cutting out

@javincruz448 2 жыл бұрын

Great video!

@MWLaser 2 жыл бұрын

Thanks!

@natashaapplebyrahim2065 2 жыл бұрын

Hi, can you tell me what you mean by short circuit? Do I remove the wire from that port? My laser is not cutting and the test button was not working until I unplugged the 6 way terminal. Then the laser fired. I need to plug it back in to see if the water monitor is working as per your steps but I'm stuck. Please help! Thanks Natasha

@JohnKelso 2 жыл бұрын

"short circuit" means to run a wire between the terminals so that electricity can flow between them. In his illustration, the yellow line is a wire.

@natashaapplebyrahim2065 2 жыл бұрын

@@JohnKelso Thank you :) I figured it out in the end.

@victoria3668 4 ай бұрын

Hii! My husband and I have a co2 laser machine and a while back it stopped functioning properly and now it doesn’t stop lasering between paths. How can we fix this ? It’s a Katian USA

@gabrielmdo5666 29 күн бұрын

If you have a Ruida or other DSP controller and are seeing this happen, it is most likely a dying high-voltage power supply unit (PSU). The drive circuit that turns the laser power off and on tends to go first, before the part that controls the overall power level.

@l2millenium 2 жыл бұрын

I just bought K80 aka red Chinese laser. I am trying to test fire (pulse), but nothing happens. Water cooler is turn on and running (if its not, and I try press pulse it gives error about water flow). Lid is closed When I click TEST on the power supply it fires. Where else can be the problem?

@SavageSmithy 2 жыл бұрын

I have a 150w laser tube and the 150w cloudray laser power supply with the screen on top you showed in the video, up to around 50% command power the laser cuts just fine but anything over that and it doesn't cut atall. I noticed some arcing internally to the annode? Ring on the output side, the arc just sort of dances around the ring I've heard conflicting information that this is normal but I have no idea. The tube has only done about 10-20 hours in the lifetime of the machine (probably 5 years old barely used) I've swapped the power supply and flushed out the water with fresh distilled and it hasn't really helped. Any ideas?

@voyager3355 Жыл бұрын

Dear Mr. Matthew thanks for this really educative video. I have a strange issue that, after replacement of Laser Tube 40W and Power supply 50W with compatible new ones both from VEVOR (this is a 50W Chinese one), Laser does not stop firing also during travel. I mean as soon as I power my machine, it goes to zero point to engage limit switches, and turns back to preset axis by leaving a really unexpected line over the workpiece. Something (what i dont know) keeps the laser on, even with a weak light. I am helpless from reseller, any suggestion will be really important. I have videos, parameters, wiring etc. if may support my question and if you want to see. Please help me, I am ready to cover any costs occured. Thank you Regards

@baddogace221 Жыл бұрын

voyager3355, I am having the same issue recently. Swapped the power supply wired exactly the same as the original and now it fires all the time or while traveling. Did you ever find a resolution and what was it? Thanks in advance.

@voyager3355 Жыл бұрын

@baddogACE Hello. I have changed both laser tube and power supply with non luck, and I used to purchase a brand new unit. Since I need the machine. I think to solve the issue, you need to replace the PLC main board. Because my problem originated from a blown co2 tube due to lack of cooling. that probably caused a short circuit at unit and all these things happened. I am sorry for you. Thanks. Regards.

@shoaibali-ro5pj Жыл бұрын

I'm using 130 EFR f6 laser tube I just changed reci T6 but it's not working perfectly do you have idea it's power supply different or other settings?

@RCjunkie Жыл бұрын

how do you do a test with out a test button? is there a way to do a jump wire to test burn?How can I talk to you?

@suhasghodekar3024 9 ай бұрын

I have a problem that my laser tube is automatically firing the laser during moving the laser head from one place to another place kindly give a solution

@jamesjabarian6011 Жыл бұрын

If the problem is on the control line what could be the cause ?

@babyayalew8059 2 жыл бұрын

Hey sir can you tell me why laser not stop emitting when it travel?

@brianbean19 2 жыл бұрын

I’m having the same issue. Let me know if you have figured it out

@babyayalew8059 2 жыл бұрын

@@brianbean19 when I trase the bord I found some short elements now I am going to change the bord.

@voyager3355 Жыл бұрын

Hello! i have the same issue! laser does not stop during travel! and ruins my workpiece. May it be the Controller defective?

@babyayalew8059 Жыл бұрын

@@voyager3355 it is tube power supply problem. If you can try by changing another power supply

@voyager3355 Жыл бұрын

@@babyayalew8059 thanks! I did all. And i am convincere this evening that I have blown out my PLC. Unfortunately. But like this. 1. Water flow sensor is broken. 2. Even water flow sensor short circuited laser travels with light. 3. Each port makes the same even laser tube 1 or 2. I am convinced to purchase new one.... Unfortunately. Regards.

@andrishiapani6221 Жыл бұрын

What happens when the laser is working in full power even when the power in settings is low or even zero?

@wajdialjghami9396 Жыл бұрын

my machin ( laser co2 work space 120 * 160 cm )makes self restart ......do you have please any solution

@duanecalhoon3322 Жыл бұрын

Wondering if you would have any knowledge of the red/black laser??? Min start up fine, runs for 20 seconds then loses all power except for lights and a fan on the door of the components. When I shut it off and let it sit for awhile it will start back up and same thing

@MWLaser Жыл бұрын

Sounds like a DC power supply issue. IF the door fan and lights remain on these usually are powered by mains. so, with machine coming on and then controller turning off would indicate that if you change out the DC power supply the issue should be resolved.

@TheUnofficialMaker Жыл бұрын

I guess this channel is off the air.

@MWLaser Жыл бұрын

Not yet. Just been busy with laser service work. Hopefully back sometime this year.

@cd3845 2 жыл бұрын

My problem is when I turn on the machine, it powers up but the ruida monitor does not, hence my laser does not operate. The machine fan and light inside powers up, but not the laser. does that mean I need a new ruida system?

@BrilliantDesignOnline 2 жыл бұрын

IF you know what you are doing, check the 24vdc power supply to make sure it is putting out; normally there is a green LED to indicate power, but use a multimeter to check for 24 vdc out. Make sure the connector from the 'motherboard' module to the display module is plugged in at both ends. For starters.

@cd3845 2 жыл бұрын

@@BrilliantDesignOnline the machine has green lights on everything. Pretty sure also from the power box, as I said the fan was running. Does that not mean anything? Will the ruida panel have lights on when functioning properly?

@BrilliantDesignOnline 2 жыл бұрын

@@cd3845 I don't know your specific machine. You cannot be 'pretty sure'; you need to know the systems, so I would recommend having someone local look at it. Also, you should share the manufacturer and specs to give us a better idea at what we are dealing with. Perhaps Matt has an idea, but the best bet is probably not on YT, at least for diagnoses.

@MWLaser 2 жыл бұрын

email more info to askmatt@mwlaser.com.au

@roadto63kg77 Жыл бұрын

I hv experience like this.. im using top wisdom.. the board was faulty.. swap with other mchine panel board.. then its working fine... need to replace the ckntrol panel board..