Cold Laminate techniques, 3 ways to laminate jobs

Рет қаралды 7,518

Күн бұрын

This video I describe and demonstrate 3 different techniques for cold laminating your BN-20 jobs.
Custom jobs thru Roland BN-20. Laminating Demo, laminate techniques and mistakes if not done correctly.
Where I bought BN-20- colemanandcompany.com
cold Laminator I use- a.co/d/3rNh9vE
Resources for material:
colemanandcompany.com
signwarehouse.com
My website Down2stick.com
My Etsy shop - www.etsy.com/s...
My Ebay store- www.ebay.com/s...

Пікірлер: 24

@tarleyc8016 3 ай бұрын

Great video! Thank you!

@jflores0002 26 күн бұрын

Awesome! For sure you helped me bud,. Many thanks!

@down2stick203 25 күн бұрын

So happy to help thank you for watching.

@sparchiayaturner2266 2 ай бұрын

Thank you

@jcampo89 Жыл бұрын

Good shit dude. Thanks for the video, it's super helpful. I was just buying a manual cold laminator and was wondering how to properly use it.

@lindaolson8565 6 ай бұрын

Great video...thanks! I just bought a Roland BN20A and want to make vehicle decals and magnetics. Ouch, I'm buying one of those rulers!!

@down2stick203 6 ай бұрын

Go for it! Yeah watch those fingers!

@blueghost4121 Жыл бұрын

I have an HP Latex 360 and only carry 54" rolls and 54" lam rolls. Even if I have a small job I always use my laminator to laminate.

@barbara34810 Жыл бұрын

You did a great job! Thanks for sharing. Lol!! I was eating when you showed your finger…. Lol Can you share where you buy your calendar Vinyl, HTV Please. Thanks

@down2stick203 Жыл бұрын

Can do. I will add to next video. Thanks for watching!

@barbara34810 Жыл бұрын

Can you show how to change and adjust the blades? Your videos are helping me a lot, Thanks for taking the time to do it.

@down2stick203 Жыл бұрын

I go thru signwarehouse.com for the vinyl. Prismjet is what I've been using but really want to try out Oraguard.

@barbara34810 Жыл бұрын

@@down2stick203 Thanks

@user-vq3yc1xw5k 7 ай бұрын

Hey thanks for the great Video. What laminate can i use for cold rolling. i stuck with which laminate film one to buy. Any assistance or links would be appreciated...

@down2stick203 7 ай бұрын

I love the Prismjet Laminate from signwarehouse.com. Never had any complaints.

@ivanmedina2281 Жыл бұрын

Thanks for the tutorial! Question, how tight do the rolls have to be? As the tightness in between

@down2stick203 Жыл бұрын

on the laminate I kind of do it by feel now. Too tight it will ripple.

@MichiK85 Жыл бұрын

Thanks for this video. Every time I stop there are wrinkles in it. How is that possible? I even can't stop in the middle of the job. Do you have any tips?

@down2stick203 Жыл бұрын

Do you keep rollers tight or loose?

@MichiK85 Жыл бұрын

@@down2stick203 I think it’s not right enough then

@sudarphotos-signs Жыл бұрын

good, what lamination sheet do you use

@macvideoworld Жыл бұрын

Ouch! I felt hurt myself, while watching how you cut your finger. Please be very careful. I think a safe way is to cut slowly, so you have more control over any accident and stop it before going too far, as well as it wont skid. My trick is apply less force/pressure on the blade, just enough to cut the paper, and go slow. I hope you never cut yourself again doing this process. But other than that good techniques and thanks for the video.

@down2stick203 Жыл бұрын

yeah I learned the hard way ha.

@The_AlexK_Project 2 ай бұрын

Good advice. I was looking at getting one of those laminators and now I will. Though the irony of laminating laminating a sticker about freedom using all tools made in a communist country is sad. Its so expensive to buy American its made the country dependent on China for our standard of living. I think the only American thing I buy is the Transfer paper I use.