Grace makes a set of Colt SSA screwdrivers. Right tool for the job.
@bobrobertson6514Ай бұрын
Nice, concise and no music, good one.
@bruceharris46438 жыл бұрын
Thanks, buddy! Nice, clean video. Just used it to replace my first bolt spring. 15 minutes and done. Appreciate it!
@geraldkeller29372 жыл бұрын
Hi, along with other reader comments, I am giving you top notch review for this video. I just got an old Colt SAA first gen gun at auction and watching this makes me feel prepared to open it up. I can see on the pictures the trigger guard plate to frame is not flush, so I will need to look at it to see if the trigger spring screw is backed out or what, lol? Anyway big thanks for the detail on this!!!!
@frankwood76174 жыл бұрын
Great Tutorial - My Colt SSA had a jammed cylinder stuck - I did a total disassembly and fixed the problem.
@docmason96778 жыл бұрын
Despite the other petty comments about your use of screw drivers this video was a great help in replacing the hand spring assembly in my Uberti Cattleman. From what I could see you were pretty gentle in removing and replacing the screws and didn't see any marred heads on the screws or scratches on the frame. I'm adding your video to my favorites for future reference. Thanks again!
@binness9 жыл бұрын
As others have noted, you are not taking care with your screwdriver work, you must have the full set of Screwdrivers so why not use them, it is no good talking about taking care and then, slipping and sliding with tips of the screwdrivers, but the instructional part of the video was ok, so thanks for uploading, but please take care of the guns, they are only on loan to you in your lifetime, then somebody else will carry on looking after them, so try and give them as good a start as you can. ATB
@ImminentThreatDefense8 жыл бұрын
Nice detail, thanks for sharing
@dustyfarrow22596 жыл бұрын
I cringed every time the screwdriver slipped
@si_vis_pacempara_bellum49065 жыл бұрын
I have a Uberti Cattleman 2 with the retractable firing pin, might wanna convert it back to the original design. This video will come handy when my parts arrives!!! Thank you so much!
@louisclemento99825 жыл бұрын
Wow, good video but I wouldnt let you in the same room with my SAA unless I had duct tape on your hands to prevent you from holding a screwdriver!
@aaaaaaaaaaaaaaaaaaa4203 жыл бұрын
Legend has it the guns finish is completely stripped and it’s dropped $1,000 in value
@JS-wu1hg5 жыл бұрын
Is smashing it with a screwdriver required for disassembly?
@cowboybolad0128 Жыл бұрын
this channel is top I sent my friends to write to see this type of work
@nicholasmapes5 жыл бұрын
"Use quality screwdrivers to avoid marring the finish" proceeds to drop tools all over gun....
@comradjacks4 жыл бұрын
literally the only thing i was thinking about.
@FORTUNENGLORY7 жыл бұрын
Apparently there is a need for a video on how to use a screwdriver.
@ace76268 жыл бұрын
Great video man.
@rolyatknarfable6 жыл бұрын
If you're taking apart an Uberti Cattleman, watch out. There's a pin and spring behind the cylinder hand that is accessed through a hole above the left backstrap screw on the back of the gun.
@scarlettacres6 жыл бұрын
Thank you. I was struggling for 30 minutes trying to get that pin in place.
@ritesideofthefence58575 жыл бұрын
Good information, thank you for sharing.
@therealhawkeyeii78884 жыл бұрын
How do you properly tighten the cylinder pin latch, since it has screws on both sides. Two screwdrivers at once? I guess you'd need to put the gun in a vice to do that.
@cowboybolad0128 Жыл бұрын
make a video showing very closely every detail of the weapon every hole every screw
@manoszervos9764 жыл бұрын
Is the barrel a different part or it is an integral part of the frame? Because in the air fun replica of the pistol it is a different part screwd and even it is well screwd it is slightly loose, still I am told that this is normal for an air gun.....
@zachparker7787 жыл бұрын
Lucky Gunsmithing, I badly need to know how to take off the loading gate, there seems to be no spring holding it closed and it keeps falling open.
@allennance9496 жыл бұрын
Should be a small spring and screw.
@edboczek99392 жыл бұрын
Can someone recommend the right screwdrivers for Uberti SAA. The slots in the screws are not as wide as the Colt. The Grace screwdrivers are too thick and do not full seat in the slot.
@tunakann76293 жыл бұрын
The hammer on my grandpas isnt uh... fully.. hammering? It wont move far enough to strike. Does anyone know what the problem might be?
@mattpatton88873 жыл бұрын
Without any additional details, I’m going to provide my best guess. If it’s an Italian clone, there’s a good chance it may have the longer, double notched cylinder base pin. This has two notches and is longer so that it can basically be over inserted and block the hammer from falling all the way. Try removing it, checking to see if there are two notches, and if so, reinsert it only to the first notch and see if that fixes the problem. If not, is there any mark at all on the primer? You may be getting light strikes which could be one - or all - of a couple different issues. Let me know if the cylinder pin solved it.
@gnystrom13 Жыл бұрын
Good video but be more careful with your screwdriver
@Brenny6278 жыл бұрын
My pin is stuck and the cylinder wont come out, can I take it a part without taking out the cylinder
@Master...deBater8 жыл бұрын
You can but I wouldn't recommend it. The problem will arise when you go to put it back together again. Likely the bolt will not want to reengage into the cylinder slot without some fuss. You're going to have to remove the base pin at some point anyway...so you might as well get yourself a base pin removal tool. Their not cheap but if you're going to own a Colt you'll want to avoid buggering up your base pin with a pliers or something. www.brownells.com/gunsmith-tools-supplies/handgun-tools/takedown-tools/colt-saa-base-pin-puller-prod10997.aspx If need be...you might want to use some penetrating oil to loosen the base pin...just make sure it's something that won't harm your finish or wood grips if you have them.
@archangel200316 жыл бұрын
I found that if you push that cylinder pin in and use it as a safety, when the hammer Falls, it will Dent the notch preventing the pin from coming out. I had to disassemble my gun and use a punch to get the cylinder rod out and there is a little dent in there from the hammer pushing it forward. Now I have a tiny barrel-shaped coil spring and pin that I have no clue where they go and I don't see him dealing with it either.
@chriscunningham65106 жыл бұрын
For anyone reading this and having a sticking cylinder pin, you can get a special tool from brownells that is specifically designed to remove the cylinder pin.
@lond28355 жыл бұрын
I have a base pin that is stuck so bad that I can't pull it out with channel locks- pin be damned! I will replace it, but how do I GET IT OUT?
@johnclarke56275 жыл бұрын
Lon D www.brownells.com/gunsmith-tools-supplies/handgun-tools/takedown-tools/colt-saa-base-pin-puller-prod10997.aspx
@georgecostanza25142 жыл бұрын
Lol watched this to see how to get to the loading gate and he left it alone haha
@canjo4588 Жыл бұрын
People making fun of this guys screwdriver skills let’s be honest we all been there
@tomcopeland74182 ай бұрын
Yeah but we learned before we showed those skills to the world.
@canjo45882 ай бұрын
@@tomcopeland7418 honestly it’s the best learning experience I’m sure a lot of people harped on him for it and now he learned something because he showed the world
@brian7becker4 жыл бұрын
"Six bullets. More than enough to kill anything that moves."
@eddiesouthgate66543 жыл бұрын
Might want to start with the dude holding the screwdriver .
@GoBob173 ай бұрын
good info but painful to watch screwdrivers sliding off the screws... cringe
@cowboybolad0128 Жыл бұрын
I wanted to know and see this detail of the dog up close > hammer how to make it stronger how to have a stronger beat
@Gurkenkasper4 жыл бұрын
Die Bratwurst, ist vergänglich so wie eine Welle im Meer, darum nie den Senf vergessen zur Bratwurst! !
@joecachia23 ай бұрын
I would not call this a 'field strip' .... you won't do this in the field . This is more like a detail strip .