Complete Cylinder Head Removal & Install On Popular VW, Audi 2.0 T TSI Engine Gen 1,2,3 2008 & Up

Рет қаралды 86,372

2 жыл бұрын

Complete cylinder head removal on popular VW, Audi 2.0 T TSI engine to replace cylinder head gasket, removal of intake and exhaust manifolds, timing chain and components.
❗️If you find this video helpful, I would appreciate a $uper Thanks that can be found below the video. Thank you!
Torx Bit Socket Set
www.amazon.com/dp/B07M9ZF35W/...
Triple Square Spline Bit Socket Set
www.amazon.com/dp/B07JYCWQQ6/...
Crankshaft Pulley Holding Wrench
www.amazon.com/dp/B08JC7PJR2/...
Camshaft Crankshaft Engine Timing Tool
www.amazon.com/dp/B08T93SB8S/...
VW/ Audi 2.0 turbo 2008-2013 Timing Chain Tensioner Failure
• VW/ Audi TSI 2.0 turbo...
How to Replace Upgraded Timing Chain Tensioner on 2.0 TSI VW/Audi 2008-2014 engines:
• How to Replace Upgrade...
Also watch my other video on faulty PCV (Positive Crankcase Ventilation) that can lead to a massive vacuum leak and/or blow the rear main seal causing serious cost to replace:
• 2.0 TSI Engine Serious...
Timing Mark Alignment for Valve Train On 2.0 Turbo VW And Audi 2008-2015
• Timing Mark Alignment ...
Serpentine Belt Removal and install on VW Volkswagen 2.0 turbo engines 2008-215 - Simple & Fast
• Serpentine Belt Remova...
Cranks But No Start? - VW Passat, Tiguan, GTI 2.0 turbo 2008-2013 - Check This First
• Cranks But No Start? -...
How To Diagnose & Fix a P2440 Code on VW / Audi 2.0 Turbo TSI 2008 & Up
• How To Diagnose & Fix ...
VW and Audi Models with the 2.0T TSI engine:
VW MK5 GTI 2.0T TSI 2008.5-2009
VW MK6 GTI 2.0T TSI 2010-2011-2012-2013-2014
VW MK5 Jetta 2.0T TSI 2008.5-2009-2010
VW MK6 Jetta 2.0T TSI 2011-2012-2013-2014-2014
VW B6 Passat 2.0T TSI 2008.5-2009-2010
VW CC 2.0T TSI 2009-2010-2011-2012-2013-2014-2015
VW EOS 2.0T TSI 2008.5-2009-2010-2011-2012-2013-2014
VW Tiguan 2.0T TSI 2009-2010-2011-2012-2013-2014-2015
VW Beetle 2.0T TSI 2012-2013-2014-2015
Audi A3 2.0T TSI 2008.5-2009-2010-2011-2012-2013-2014
Audi MK2 TT 2.0T TSI (not TTS) 2008.5-2009-2010-2011-2012-2013-2014
💰Save money on other vehicle maintenance and repairs :
Top 3 Reasons Why Your Car Won’t Start
• Top 3 Reasons Why Your...
Pittsburg Harbor Freight Engine Support Bar 1000lb. Capacity - Review& Install
• Pittsburg Harbor Freig...
How To Remove A VERY Stripped Lug Nut - When All Tools Failed - Guaranteed
• How To Remove A VERY S...
Cheap Way To Check For Bent Valves Without Removing Cylinder Head
• Cheap Way To Check For...
Brake Burning Smell? - Frozen Brake Caliper Replacement on Any Car
• Brake Burning Smell? -...
Brakes Dragging? And Not a Frozen Caliper?
• Brakes Still Dragging...
Save money and learn how to bleed brakes by yourself on any car
• Save Money And Learn H...
How to properly gap spark plugs
• Car Misfiring? Running...
Proper way to install valve stem seals
• Proper Way to Install ...
Hot Tip: Broken Stud Removal
• Hot Tip: Use a Torch f...
Remove a Broken Stud Below the Surface
• Remove a Broken Stud B...
Oil Bearing Clearance measuring - simple to understand video
• Oil Bearing Clearance ...
Symptoms Of A Seized / Locked Engine - How To Tell It’s Not A Bad Starter
• Symptoms Of A Seized /...
How to properly gap and install piston rings
• Piston Rings Replaceme...
How to check cylinder head or block deck for warpage
• Cylinder Head Warpage ...
Why is it important to replace the timing belt at the manufacture’s intervals
• Check and Change Your ...
Fast & Easy way to lap “grind” intake and exhaust valves
• Seating Intake & Exhau...
Replace Front Exhaust Flex Pipe on most 4 or 6 cylinder cars - Cheap Way
• Replace Front Exhaust ...
Better Throttle Response in Minutes
• Better Throttle Respon...
⁉️QUESTIONS
If you have any questions or I missed something, comment below and I’ll answer and try to help you out
If you find this video helpful, like it and subscribe to my new channel. I’ll have tons of videos on all kinds of car and truck repairs in the
future.
⚠️Disclaimer:
The videos on Motorcarnut channel are posted with informational purpose only.
Information posted in this video does not guarantee any particular result. Use this information provided in the video with caution and at your own risk. It is the responsibility of the viewer to take this risk.
Motorcarnut is not responsible or liable for property damage, any loss damage, or injury related to or resulted from information posted in this video.

Пікірлер: 299

@shanes1221 Жыл бұрын

Thanks for making this video. I have basic automotive knowledge and was able to complete this job instead of junking the car like the wife insisted on 😂. Just started it today and it sounds great. Couldn’t have done it without this detailed video. Much appreciated!

@Motorcarnut Жыл бұрын

Wow, that’s awesome, thank you for such a nice comment, you made my day!

@torreycoates7584 Жыл бұрын

Shane, how long did it take you?

@Udin.14 Жыл бұрын

@@torreycoates7584the shop ltlho pn

@sergeyshtriter5643 Жыл бұрын

At first I thought this video had millions of views because it's awesome, thank you very much.

@Motorcarnut Жыл бұрын

Thank you, I appreciate it!

@eliseogloria892 Жыл бұрын

@@Motorcarnut ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤😂🎉❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

@Motorcarnut Жыл бұрын

Wow, much love as well!!!

@gee3883 5 ай бұрын

Brilliant vid dude, thanks for doing this in depth tutorial. I've just replaced the chain and tensioner and in doing so realised the gauze from the cam bridge was missing. I took the cam covers off to search for it. As I removed the cover the cams lifted and I shit a brick as Ive never done this kind of repair. i'm confident I can put it all back together now thanks to you. It seriously is so helpful as I am in a remote place 35 miles from the nearest garage you got me out the shit dude. Cheers and blessings from a not so stressed Englishman living in Lithuania.

@Motorcarnut 5 ай бұрын

Hey, no problem and good luck!!!

@taaiz01 Жыл бұрын

Thank for your time, for that absolutely perfect detailed video! So very helpful!

@Motorcarnut Жыл бұрын

You're very welcome! Thank you for the feedback!

@user-qx3ph3xb6l 3 ай бұрын

I checked a lot of VW fix up videos, you are one of the best. Great work. I am such a critic, I don’t leave great comments like this at all.

@Motorcarnut 3 ай бұрын

Wow, thanks! It means a lot! Comments like yours motivates me to keep going!

@ashleygeiger440 Жыл бұрын

Thanks for this video! Recently got a 2010 VW passat wagon, about 156k miles on it, drove for 5-6 days and the timing system caputted on me. It had misfires so tried changing the spark plugs and coils, aided for a bit, then coming home one day the car wouldn't accelerate and started shaking. Luckily I was only going 35-40 mph when it happened so things aren't likely torn up entirely in the engine. Trying to fix this sucker up but can't find a good manual at a reasonable price, so this video helped a lot!

@Motorcarnut Жыл бұрын

No problem, thanks for the comment. I have more videos on these engines on all their problem areas.

@connor9018 Жыл бұрын

Hi, great video I’ve used this as my main resource to fix my scirocco. I’m currently rushing to get it all done before uni!! This vid has saved me from a fiat panda haha thanks

@Motorcarnut Жыл бұрын

That’s great, thanks for taking the time to comment I appreciate it.

@tylerrosser5938 Жыл бұрын

this is an amazing video, my cc also had the dreaded timing failure. its funny becuase someone warned me about it and told me to replace the tensioner, and i procrastinated too long lol and sure enough, it went bad. thanks for the detailed video, it helps a lot!

@Motorcarnut Жыл бұрын

Thank you! Sorry you have to go through this. You most definitely bent all the intake valves, the exhaust valves are probably fine as well as the cylinder head and the pistons.

@tylerrosser5938 Жыл бұрын

@@Motorcarnut I started taking it apart and when I took the timing cover off, the top chain guide was missing and I found pieces of it, so my tensioner might be good (still replacing anyways) but now I'm gonna replace all the guides as well

@Motorcarnut Жыл бұрын

Well that’s not good, that can happen is by a jumped timing chain. Do you have the old tensioner in there?

@bestbuildpc 6 ай бұрын

Actually it is a lot work. Incredible! thanks for sharing. I was just looking for gasket replacement for Audi A3 2002 8L1 BFQ.

@Motorcarnut 5 ай бұрын

Thank you very much! I don’t have any on the engine yet.

@larryadelberg6676 Жыл бұрын

For aligning the head, since the VW head bolts are tty, and have to be replaced, cut the heads off and cut a slot in them. Then put them in the corners a few threads deep and use as alignment. Once you put 4 in the middle, use a thin regular screwdriver to back the corners out and put the new bolts in. Then there are no alignment issues and no sliding the head around on the new head gasket. .

@Motorcarnut Жыл бұрын

You can do that but there is really no need to. The head isn't that heavy and there are 2 dowels to line up the head.

@glennrogers5826 Жыл бұрын

Here's a person that cares and is genuine u r much appreciated thank you

@Motorcarnut Жыл бұрын

Thank you! I appreciate the comment.

@glennrogers5826 Жыл бұрын

@@Motorcarnut I'm new to the vw family had nothing but problems since purchasing 2013 cc 2.0 in your professional opinion should I consider balance shaft delete kit ?

@Motorcarnut Жыл бұрын

Why would you want to do that? The balance shafts keep the engine from shaking. Would not do anything for reliability?

@glennrogers5826 Жыл бұрын

@@Motorcarnut thank you

@Motorcarnut Жыл бұрын

You’re welcome!

@stephenr1999 Жыл бұрын

wow no kidding my balance shaft links were all lined up when i pulled it apart. i have seen that on subaru timing belt once. kewl

@Motorcarnut Жыл бұрын

You got lucky

@yasirwidelensbyyasir5060 Жыл бұрын

Thank thank thank yo so much.. one of the best videos and.. amazing explanation.

@Motorcarnut Жыл бұрын

Thank you! I really appreciate you taking the time to comment.

@Giggs1oh5 10 ай бұрын

A very useful video. Thank you very much

@Motorcarnut 10 ай бұрын

You are welcome! Thanks for the feedback

@pedrocols 9 ай бұрын

I replaced the timing chain tensioner on my 2010 Audi a3 one week after I bought it with 100k miles on it. The car now has 140k and runs very smoothly. I also change the oil at least twice a year. Thank you for the video.!

@Motorcarnut 9 ай бұрын

Nice work! Thank you for the feedback much appreciated!

@pedrocols 9 ай бұрын

@@Motorcarnut You're welcome!

@pedrocols 9 ай бұрын

@@Motorcarnut Do you have any videos on misfires?

@Motorcarnut 9 ай бұрын

Yes I have many, just look up my video content and type “misfire “

@pedrocols 9 ай бұрын

@@Motorcarnut Thanks

@gamersroost Жыл бұрын

Thank you for posting this.

@Motorcarnut Жыл бұрын

You're welcome! Thanks for the comment

@Newgrower0616 11 ай бұрын

Probably should have done chain and guides. Chain looks stretched.

@Motorcarnut 11 ай бұрын

Yes, I always do.

@Newgrower0616 11 ай бұрын

@@Motorcarnut doesn’t look like you did it in this video looks like old guides and chain with just a new tensioner. Why is the tensioner so far out of its a new chain.?

@Motorcarnut 11 ай бұрын

@georgehawksley2287 sometimes I make the videos on old engines just to show how it’s done, not necessarily I’m working on a customer’s car. That’s why.

@rickyjeyvernet9055 Жыл бұрын

Great video. Well explained 👍

@Motorcarnut Жыл бұрын

Thank you very much, appreciate the feedback.

@dabo8601 7 ай бұрын

Great video, thanks for sharing😊

@Motorcarnut 7 ай бұрын

No problem and appreciate the feedback

@nickmicdickerson 3 ай бұрын

your the boss MAN!!!! thanks bud

@Motorcarnut 3 ай бұрын

Glad to help!

@zachs1545 Жыл бұрын

Thank you so much

@Motorcarnut Жыл бұрын

No problem, thanks for the comment

@chrisdelarche4446 Жыл бұрын

You're the best !!

@Motorcarnut Жыл бұрын

Thank you! Appreciate the comment!

@MedicalTuition 6 ай бұрын

Amazing video thank you for your work. How do we bend that lower exhaust manifold bracket back to get the bolts on?

@Motorcarnut 6 ай бұрын

Thank you! Just use a crowbar to bend it enough to thread the bolts

@albertoledezma5790 Жыл бұрын

Gracias Mr MOTORCARN. Voy a ajustar un motor igual con tu video ya me di una buena idea de como lo voy hacer saludos de cdmx ciudad de mexico ha le va su buen like gracias

@Motorcarnut Жыл бұрын

Thank you for the kind words!! And good luck! If you have a problem let me know!

@theGinthebuilding Жыл бұрын

All my days as a vw master tech I've never heard of a triple torx lol

@Motorcarnut Жыл бұрын

I know, triple torx or triple square

@jimmiewilliams5972 5 сағат бұрын

Very detail

@Motorcarnut 5 сағат бұрын

Thank you! Cheers!

@James-mc3mg Жыл бұрын

life-saver of a video!! by any chance did you torque exhuast manifold before or after torquing the cylinder head on? thank you for this video :)

@Motorcarnut Жыл бұрын

Thanks for the comment, appreciated! Yes, After the head was torqued.

@ErvinPeitz Ай бұрын

Excellent explaination. Do you have a video on replacing a vlave cover gasket on a 2018 VW Passat r-line 2.0?

@Motorcarnut Ай бұрын

Thank you! I do not at this time sorry

@Mikethemechanic2023 Жыл бұрын

Absolutely great reference! Did you do a video on the head rebuild? Link Please?

@Motorcarnut Жыл бұрын

Thank you! I didn’t but I will be doing another head soon and will make another video at that time.

@stephenr1999 Жыл бұрын

thank you for making this video. the book ( alldata) sux pretty bad for this timing setup

@Motorcarnut Жыл бұрын

No problem, thanks for the comment

@codyn.7285 8 ай бұрын

Change your glove!!! Jk awesome video man, I love how detailed it was.

@Motorcarnut 8 ай бұрын

lol, I did. Thank you for the feedback, really appreciated!

@maxt590 4 ай бұрын

Thanks for the video! Which screws besides the head bolts did you renew? VW noticed a lot of screws as single use in their work instruction, for example all screws of the metal timing chain cover, all torx30 of the camshaft frame and so on...

@Motorcarnut 4 ай бұрын

Just the head bolts all the others are perfectly fine.

@ClosRC Жыл бұрын

Thank you for making the video. Im having an issue, i cant take the crankshaft bolt out for the life of me. Any tips? I have the tool to hold the pulley and everything but it won't budge.

@Motorcarnut Жыл бұрын

Thanks for the comment. If you don’t have a powerful impact gun, You have the long tool with the 4 pins that lock into the crank pulley? Then you take a 1/2 drive and I believe a 24mm socket with a breaker bar and break it loose.

@reinholdhakandonga5591 10 ай бұрын

Your the best

@Motorcarnut 10 ай бұрын

Thank you! Appreciate the feedback!

@rehabdre2843 5 ай бұрын

Just doing a valve cover do I need to take off the and the harmony v balancer and use that special tool for that value

@Motorcarnut 5 ай бұрын

@TRAyres 2 ай бұрын

12:53 - "I took the inspection plug out. I have a video on this also." What video? You've got a lot of videos! Also I greatly appreciate it; thank you!

@Motorcarnut 2 ай бұрын

What are trying to do?

@TRAyres 2 ай бұрын

@@Motorcarnut Well I've got a 2011 GTI and the timing chain got off and the valves got busted, so I'm trying to pull the heads off to take it to a machine shop. Then I guess I have to put it back together... Anyway, I wanted to pull out the inspection plug and maybe see what I can learn, because I have to get familiar with all this stuff to keep this car running forever. Your videos are amazing and I appreciate it so much, thanks again!

@Motorcarnut 2 ай бұрын

Sure no problem! Just search my timing chain tensioner VW videos

@emondsan 20 күн бұрын

Any trick to getting the exhaust manifold off? Got the bolts off and it slides up but won't clear the lip. Drop the engine down a bit on the jack? Raise it? UPDATE: had pull the engine toward the front of the car and it came right out (have the motor mount off already)

@samcarroll7994 4 ай бұрын

Hi there, thank you so much for this video, the manual I bought wasn’t helping. I was wondering what I should do if the 6mm hex plug on the exhaust manifold heat shield 36:44 starts to strip? Should I use a bigger size torx and try to hammer it in?

@Motorcarnut 4 ай бұрын

I know that bolt is such a pain if you strip it and that bolt really serves no purpose. Yes try to hammer it in if you can with such little room.

@lildoorknobb5954 4 ай бұрын

Great video with great detail! Now i have a mk6 gti with a bad piston ring which is allowing boost to get past the piston and into the oil pan causing it to leak. Will i need to remove my entire engine to take out the piston or can I just pull the head and oil pan?

@Motorcarnut 4 ай бұрын

I don’t believe you can get to all the connecting rods just by removing the pan.

@neilhampson2843 Жыл бұрын

Thank you for taking the time to make this video. I am on with a Skoda Octavia, in the UK, which has the same engine. I don't think you have the Skoda models over the pond. Have you ever had issues not changing the injector seals?.

@Motorcarnut Жыл бұрын

Thank you!, Every now and then I see a Skoda. And you don't have to replace them if their not damaged. Just clean them and put some oil on the seals and you'll be fine.

@neilhampson2843 Жыл бұрын

@@Motorcarnut Thank you for your speedy reply. I will give the injector seals a go. I have changed them in the past and they did not feel any different to the used ones. Keep up the good work. And thanks again form the UK

@Motorcarnut Жыл бұрын

Thank you, really appreciate it. Good luck

@emondsan 26 күн бұрын

Thanks for the video, attempting this repair after learning I have 8 bent intake valves. What sealants do you recommend for the valve cover, lower timing cover, and vacuum pump seals? OEM or have you found out aftermarket work better and last longer?

@Motorcarnut 18 күн бұрын

I believe i answered your question before?

@richardcraig2792 Жыл бұрын

Thanks for the detailed instructions and video. Do I have to take off the cam cover to remove the head ? eg can i access all the head bolts through the cam cover ?

@Motorcarnut Жыл бұрын

Thank you! Yes cam cover has to be removed.

@Motorcarnut Жыл бұрын

@fireerik Жыл бұрын

Watching this as I’m half way through my 5th one of these just to compare methods

@Motorcarnut Жыл бұрын

Great. I don’t do these videos for speed, but for people to understand as simple as I can make them, so they get the confidence to tackle it themselves and save a lot of money doing right themselves.

@fireerik Жыл бұрын

@@Motorcarnut gotcha yea, I have a similar system to doing them but have to do them with speed so I take things out in chunks, like the air filter for example I just undo the connector, move the clamp and remove the t30 then pull them entire thing out in one

@user-ni4py2ds5e 8 ай бұрын

Mejor imposible hermano, voy a meterle mano, tengo que hacerle eso mismo a mi carro, me lo han trasteado en un taller supuestamente profesional y lo que hicieron fue devolvermelo mas malo que como estaba. Con este video lo voy a hacer yo mismo. Saludos!!!

@Motorcarnut 8 ай бұрын

Thank you! Good luck! If you run into a problem let me know.

@85on4s 9 ай бұрын

Hey im stuck at the exhaust manifold i bent the lower bracket off the motor and removed the top 4 bolts on the manifold but i cant get the manifold to move out of the slot any advice car is a Volkswagen CC

@Motorcarnut 9 ай бұрын

Yes, lift manifold up off the slots evenly on both sides then get I crowbar and put it in between the manifold in the middle and pop it out. It’s tight but comes out.

@saulsanchez9856 Жыл бұрын

Amazing video!!! Thank you very much for helping out.

@Motorcarnut Жыл бұрын

No problem, thanks for the comment

@paulw2583 2 ай бұрын

Amazing video. Still scared..!!

@Motorcarnut 2 ай бұрын

Thank you! Don’t be if you get stuck give me a holler.

@matthewhill2142 7 ай бұрын

extremely informative....so informative, that I've decided that I will NOT be doing this. Time to push it out into the highway...

@Motorcarnut 7 ай бұрын

Sorry about that. It ain’t that hard if you’re mechanically inclined and have some special tools.

@interlogic1 Жыл бұрын

Hello, Was the valve guides cracked, Is it common for the valve guides to crack on this type of head? Thank you for sharing and have a great day.

@Motorcarnut Жыл бұрын

Good question, no and I’ve done over 75 of these and none were cracked.

@jefaismoimeme6833 Жыл бұрын

@@Motorcarnut how do you check this valves guided ? Is there a procedure?

@oomgloff2 Жыл бұрын

is it absolutely necessary to replace the head bolts or any other bolts with new ones?

@Motorcarnut Жыл бұрын

On this VW engine the head bolts torque to yield so they must be replaced, other bolts on this engine you can reuse.

@zoden6305 3 ай бұрын

Question and sorry if it’s a bad one. If I have a leak on my vacuum pump then I cannot just take it off like you did in the video and replace the gasket for it and torque it with gasket seal? Do I have to get a new engine or do I have to replace the whole thing? I found this video so I could work on my MK 2 TT because I noticed an oil leak and I wanted to see if a head gasket would fix the problem plus just doing maintenance as there’s nothing wrong with the car but just that leak. Thank you for the video as well!

@Motorcarnut 3 ай бұрын

You can just remove the vacuum pump and clean the old gasket and surfaces and reinstall but don’t put too much gasket maker or you can clog the oil ports.

@zoden6305 3 ай бұрын

@@Motorcarnut thank you, will be doing this and I’ll give an update and hopefully I don’t have to do any timing chains but I will have to do my belt soon as im nearing 100k miles

@torreycoates7584 Жыл бұрын

Do I need to put the car on a lift? I know it will make the remove/install easy but I don’t have access to one.

@Motorcarnut Жыл бұрын

Absolutely not, just make sure when you jack up the car put jack stands underneath securely before going under the car.

@donopp5850 Жыл бұрын

Is the FSI pretty much the same procedure ... Except I know it has a timing belt, not chains ?

@Motorcarnut Жыл бұрын

They are similar, yes

@suprarace 3 ай бұрын

Do you oil the head bolts before installing and torquing the head bolts?

@Motorcarnut 3 ай бұрын

Yes, just a light coat

@Roverturbo Жыл бұрын

Hi 20 mins in and your already talking about removing the timing cover. Is it possible to remove the head without doing this? Ie de tension the tensioner and slip off the chain from up top and leave in situ? Thanks.

@Motorcarnut Жыл бұрын

Unfortunately not, Has to be done the proper way or you will never get the car to run right. Plus its a great idea to replace the timing chain tensioner while you're there because if it's an old one it will fail and destroy your engine, I have many videos you should check out on that as well.

@rehabdre2843 5 ай бұрын

Wat about the valve cover

@Manylfotiou 5 ай бұрын

Great Video! Got a 2009 VW CC (fifth Vin Digit is a "L") with a TSI CCTA engine with high miles and had major failure of the timing chain & tensioner. Looking to purchase a used ccta engine to swap into it. I see a lot of Tiguans for sale up to 2018. I'm looking for a newer/newest possible used engine that is compatible....What is the latest year CCTA engine swap that I can I purchase without total chaos and ease?

@Motorcarnut 5 ай бұрын

Best thing to do is go on a site like carparts, it's a salvage site and put in your vehicle info and select highest years and you'll see the highest.

@Manylfotiou 5 ай бұрын

Thanks again for the info and such quick response! I was on that site when I commented (I have been using it for years). I found it hard to believe that it goes to 2018 CCTA 2.0.. Can you please help with recommending trusted parts suppliers so I might possibly help credit you for your time and expertise? Obviously a new timing belt kit should be installed; are there any other items that i should replace prior to install to reduce possible future problems? Replace things like the rear main seal, water pump, sensors etc. to have extra peace of mind? Anything that should be avoided? Second opinions are always better than second guessing!!! Much appreciated

@Motorcarnut 5 ай бұрын

I also just checked that site as well. Does go up to 2018, but not sure if intake manifolds would be different or not. They would be able to tell you when you buy it. You can just swap yours over if different. I would replace timing chain tensioner, water pump rear and front main seals. I can't recommend anyone because I don't trust none of them. I would make sure I get a warranty and if you are installing it yourself make sure their warranty includes private owners installing the engine too. Also I would find one with the highest year and lowest mileage. I don' t know your budget but that's what I would do. I mean I would rebuild the engine that's in the car now with all new parts but that's just me.

@senzom4484 6 ай бұрын

Hi ...what tool you used for the exhausht menifold?

@Motorcarnut 6 ай бұрын

There are no special tool to remove exhaust manifold, Just the 13mm nuts and lift up and off.

@BUZBY1977 Жыл бұрын

How did you connect the injectors to their respective connectors with intake fitted? Is is not best to fit injectors into head first and line up fuel rail when replacing intake? Do you need new seals on injectors as recommended by others? Great video, especially the turbo removal from head, saves a lot of grief.

@Motorcarnut Жыл бұрын

You install the injectors with the intake manifold together and if the seals are not damaged you can reuse them

@OUTANDBAD33 Жыл бұрын

Hi, I've subscribed, amazing video... I'm in the UK, my head gasket has gone in my Audi a3 1.8t tfsi 2008 Cabriolet and watching your video I want to fix it myself... The tools I need, would it be ideal to get, Timing Chain kit or individual Timing Chain parts... I will be getting a full gasket set though... Plus all the tools I need but not if they come with the Timing Chain Kit... Also can I use this video to do my car, engine looks the same almost, or could you do a video on a Audi a3 1.8t tfsi 2008... Your help would be much appreciated... Keep up the amazing video's...

@Motorcarnut Жыл бұрын

Thank you very much for the comment. You can use this video for the 1.8 as well.It's a little different as far as accessories and the engine is vertical in the car. Now are you replacing valves too from a failed timing chain tensioner? Because you will need the valves as well. The timing chain kit will include both chains all guides and both tensioners, however you don't have to touch the secondary chain or tensioner if they are ok because they rarely ever fail unless you want to. Timing chain kit if you are doing both chains get the full kit if not get just the main guide rails and tensioner on ebay or amazon same the the full gasket set. Tool kit: www.amazon.com/DPTOOL-Engine-Timing-T10352-T40196/dp/B07SPW3G28/ref=asc_df_B07SPW3G28/?tag=hyprod-20&linkCode=df0&hvadid=343362361884&hvpos=&hvnetw=g&hvrand=15193194066396466452&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9004584&hvtargid=pla-784006645356&psc=1&tag=&ref=&adgrpid=70591845793&hvpone=&hvptwo=&hvadid=343362361884&hvpos=&hvnetw=g&hvrand=15193194066396466452&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9004584&hvtargid=pla-784006645356

@OUTANDBAD33 Жыл бұрын

@@Motorcarnut o wow, no thank you for the quick response... I'll be rebuilding, so everything's literally going to be new... If I have ant more questions is ok to message you...? Once again thank you so much... ❤️

@Motorcarnut Жыл бұрын

Yes, no problem

@jefaismoimeme6833 Жыл бұрын

great job man ,did you changed the valves seals for the exhaust valves or not? how did test that all the valves are well sealed after the valves job ?

@Motorcarnut Жыл бұрын

Thanks bro, yes, every time I do head work I replace the valve stem seals, and I lap the valves with lapping compound to re seat them.

@jefaismoimeme6833 Жыл бұрын

@@Motorcarnut you do that just for the valve that needs replacing ?.the other ones you don't touch them ?

@Motorcarnut Жыл бұрын

It depends, if you’re doing this big job I’d replace all of them but if you’re on a budget you can get away with replacing just the bad ones.

@jefaismoimeme6833 Жыл бұрын

@@Motorcarnut thx bro .may be i will do that in few days.i had a timing failure while crancking my engine this morning (the engine didn't even start) and the piston hit the valve .do you think that can bent a valve ?

@larryadelberg2997 Жыл бұрын

Just curious.. It looks like you released and removed the front engine motor mount. It also looks like you did not support the engine. Am I seeing this right that the engine holds sufficiently that way? Just curious as I am in the middle of one of these and I am always juggling to support the engine.

@Motorcarnut Жыл бұрын

I do have a support bar underneath the engine but you can just lower it slowly and you’ll be fine if you can’t support it.

@larryadelberg2997 Жыл бұрын

@@Motorcarnut Thanks for taking the time to respond!

@Motorcarnut Жыл бұрын

No problem

@ivanvega2821 10 ай бұрын

Greetings good Sir. I’m coming back to report that the chain job you helped me with went perfect! Now I’m having a different issue 😅 I just turned on the car this morning and I decided to unhook the intake manifold hose that goes to the PCV valve (car has been running rough at idle and stalling out with P0300 and P1250) . At the manifold hole, I put my thumb and told my buddy to turn in the car. The vehicle started and idled 200% better. I than decided to remove the PCV system so I could suck and blow inside of it to see if the PCV valve was faulty. I was able to suck and was not able to blow in, which my understanding this means it's a good PCV system. Why was the car running fine when u plugged the intake manifold hole with my thumb

@Motorcarnut 10 ай бұрын

Glad to hear that and thanks for the update!. I think the PCV valve is bad. There is a round disk on top of the PCV valve and to the right there is a small hole, with the engine running out your finger on hole and see if you feel vacuum? If you do it’s bad.

@ivanvega2821 10 ай бұрын

@@Motorcarnut I don’t feel vacuum. I unplugged the hose going to the PCV valve at the engine side (not the intake manifold side) and the car just stalled and felt no vacuum. The car runs perfectly fine when I plug the I take manifold hole and it has some serious vacuum. It gave me a hickie on my thumb 😂 Another thing that I found that’s strange. When the car is in the ON position, u her a weird clicking noise coming from the top of the HPFP. I unplug the connector that’s on top of it and the clicking goes away. I’m not sure if that’s normal or not.

@Motorcarnut 10 ай бұрын

@ivanvega2821 I’m talking about leaving all hoses connected to PCV while engine is running and feel for vacuum from that small hole on the side of the round disk. The other noises you’re hearing is normal

@ivanvega2821 10 ай бұрын

@@Motorcarnut I just tried. No vacuum at that little hole in the circular area. The vehicle runs ok at fold start but when it settles down, it just stalls and misfires like crazy 😩 I ordered a PCV valve from Amazon earlier today for $68 just to see if that’s the issue. I know it won’t be quality part but at least I’ll be able to diagnose if that’s my issue. Shotgunning parts 😂

@Motorcarnut 10 ай бұрын

@ivanvega2821 let me know how it works out!

@NWCI 2 ай бұрын

are the head bolts reusable?

@Motorcarnut 2 ай бұрын

VW head bolts are not tty meaning you can reuse them but for the cost I just replace them.

@Zajten 3 ай бұрын

Great video. I´m about to do this on my engine now for the same reason,, no compression . How many hours did it take you to do this job?

@Motorcarnut 3 ай бұрын

Thank you! Well I have all the tools and lift and do hundreds of these. To take it off should be a couple hours for you same when installing it. If you have bent valves that’s extra time as well.

@Zajten 3 ай бұрын

@@Motorcarnut i was looking for your video when you clean up cylinderhead when you change valves. but i can´t find it?

@beastmode_on1232 4 күн бұрын

What sizes do you need for the triple square bits

@Motorcarnut 4 күн бұрын

Just get a set, you’ll need about four different sizes

@mazpr2025 2 жыл бұрын

are you for real, that little mark on the metal plate, wow.... when it should be a visible indented stamp for easy timing alignment. Thank you for the video!

@Motorcarnut 2 жыл бұрын

Thanks for the comment. Yes I try to point out all the areas that may cause someone confusion and time.

@FourCeez 3 ай бұрын

Really hoping you can lead me in the right direction here. I've been working on my car for a while now same tsi engine as in the video. Recently I got a P0304 Code with a bunch of white smoke coming out of the engine bay as well as exhaust with a rough idle. Took the coil pack and spark plug out of cylinder 4 and saw that there was coolant below sadly. Could this be from a bad gasket on the intake manifold or do you think the head gasket is blown or a crack in the block? The only code popping up is from cylinder 4 so that's why I'm questioning it. Really hope you can get back to me with some sort of information, thank you!

@Motorcarnut 3 ай бұрын

You have a blown head gasket, there should never be coolant in the cylinders. That’s why it’s misfiring.

@FourCeez 3 ай бұрын

@@Motorcarnut Right, maybe I was mistaken by coolant i'm no expert lol. Could it possibly be fuel by a bad fuel injector?

@Motorcarnut 3 ай бұрын

@FourCeez yes

@hfrog713 Жыл бұрын

I believe this is same as TFSI except TSI is VW and TFSI is Audi. My engine in an 2010 Audi A3 2.0 TSI looks exactly like this.

@Motorcarnut Жыл бұрын

It is

@allanroth1 Жыл бұрын

So I'm doing this on my wife's car and the secondary tensioner was the one that failed and jumped. Can I just retime it and replace the chain/tensioner and be good?

@Motorcarnut Жыл бұрын

The secondary tensioner is for the balance shaft so yes you should be good. I never had one of those fail. Make sure primary didn’t jump because it will bent the valves.

@allanroth1 Жыл бұрын

@Motorcarnut it did that's why I'm doing it broke all intake rockers and bent all intake valves. Exhaust is untouched. But main tensioner had so much tension I couldn't move it like you did but I could do that on the secondary. Thanks for the reply

@Motorcarnut Жыл бұрын

Gotcha, sorry to hear you got to do more work.

@SavageCips Жыл бұрын

19:35 is that the Diverter valve location? Can you tell me what bit I have to use to take it off?

@Motorcarnut Жыл бұрын

Yes, I believe it’s a torx t20

@SavageCips Жыл бұрын

@@Motorcarnut much appreciated bro thank you!!!

@Noel127 Жыл бұрын

the gasket maker was put on poorly, it's best to leave a thin line following the channels and let the mating of the two surfaces spread, it's the sealant is made to be safe on the oil system if it pours over.

@Motorcarnut Жыл бұрын

The can cradle uses anaerobic sealer not gasket maker

@riccardoc3346 11 ай бұрын

Hey im having the same issue i did coil pack, spark plugs, intake manifold and still nothing. I did a compression test and all cylinders are at 125 except for the third cylinder i have no compression.... do you have a shop im in queens

@riccardoc3346 11 ай бұрын

Sorry its a 2015 vw gti cxca engine

@Motorcarnut 11 ай бұрын

Yes, but we are not in Queens.

@riccardoc3346 11 ай бұрын

What part of new york maybe i can take it to your shop

@krystlehoward4090 10 ай бұрын

What year do you have I have the exact same problem

@riccardoc3346 10 ай бұрын

@@krystlehoward4090 2015 gti S

@ourbudd Жыл бұрын

I have my car running but for some reason it keeps overheating? No heat inside either. I thought new water pump/thermostat so I replaced with the original but no help, still can't seem to get flow. Belt is good and turning? Tried everything to vent and fans run but just idling it goes over 205 and no heat and when I took it for a drive it still got hot withing one mile? Amy help is appreciated. Thanks Tim

@Motorcarnut Жыл бұрын

Did you replace the overflow cap? How’s the radiator? If both are good you can have a blown head gasket. The no heat is a sign of air in the system caused by either an air pocket or pistons pumping up the system.

@ourbudd Жыл бұрын

@@Motorcarnut I just rebuilt the motor, new head and gasket etc. I am hoping it's something simpler than that. Any tests you can suggest? Thanks

@ourbudd Жыл бұрын

I also did a pressure test at 15 and it has held overnight, I would think a head gasket leak would show there?

@Motorcarnut Жыл бұрын

Did you replace the overflow cap? And was the car overheating before you did the work?

@ourbudd Жыл бұрын

@@Motorcarnut I did not replace it, I bought the car 3 years ago with the head off and just got to rebuilding. I know I have no flow through the radiator lines are cold, no flow back to reservoir, no heat, I had put on a new waterpump but went back to the old one but no different. I am going to drain and inspect the lines to the radiator and flow some water through the radiator? Been sitting open possible he stuffed a rag or something in there? Should know more later. Thanks

@user-un6yg2sw6l 11 ай бұрын

How did you take off the exhaust manifold I can’t find it anywhere

@Motorcarnut 11 ай бұрын

I explained it in the video. Just the top bolts come out, the bottom sits in a V channel and just lifts up and out.

@ahmedsaid1823 3 ай бұрын

No easy i took out the top bolts and removed the two tts 10mm at the bottom but can’t take it out 😢

@namechane1758 Жыл бұрын

how does the bottom exhaust manifold nut/stud, next to and blocked by the turbo, come out?

@Motorcarnut Жыл бұрын

Good question, you only take out the top exhaust manifold nuts as the bottom is just slipped into a wedge groove so when you tighten the top nuts it puts pressure on the bottom and creates the seal. Also you have to take off the brace in the back of the turbo to slide the manifold up, then out.

@namechane1758 Жыл бұрын

@@Motorcarnut I figured it I have 2014 Tiguan. The bottom has clamps.

@Motorcarnut Жыл бұрын

It’s hard to help people sometimes who don’t give year make and model, I’m not a mind reader.

@namechane1758 Жыл бұрын

@@Motorcarnut no doubt, great video otherwise

@Motorcarnut Жыл бұрын

Thank you!

@luiscamacho06 2 ай бұрын

I don’t have the special tool to remove the harmonic balancer. Would it be fine if I used an impact wrench to break it loose. Remove slowly and use a bushing a some sort to put back in with the bolt to keep everything in place?

@Motorcarnut 2 ай бұрын

I wouldn’t because the ratcheting effect can cause chain damage and the spacer to hold everything in time is soft so it wouldn’t damage the teeth.

@luiscamacho06 2 ай бұрын

I can’t get exhaust off. I followed every step. Feeling like. I missed something. Even loosened the bracket it sits on

@Motorcarnut 2 ай бұрын

@luiscamacho06 bent the bottom bracket out a little and pry up and out on exhaust manifold it’s a tight fit but will come right out

@luiscamacho06 2 ай бұрын

I’m at the timing part. I did every step but the can end up about half a tooth off every time. I’ve removed and installed 4 times and same result every time

@Motorcarnut 2 ай бұрын

@luiscamacho06 what do you mean? Line up the colored links to the marks it’s not the complicated?

@mtsanchez27 2 ай бұрын

How different is this compared to the FSI from a 2008 GTI 2.0 they both look similar

@Motorcarnut 2 ай бұрын

They are pretty different

@mtsanchez27 2 ай бұрын

@@Motorcarnut nothing alike on this video then?

@Motorcarnut 2 ай бұрын

@mtsanchez27 well the FSI is a belt driven engine the TSI is chain driven. So right there they are very different and sensors are not the same, water pump is different, block etc.

@mtsanchez27 2 ай бұрын

@@Motorcarnut ok, thank you very much

@Motorcarnut 2 ай бұрын

@mtsanchez27 no problem!

@stevengolden4627 6 ай бұрын

combien de livres sur les boltes du couver

@Motorcarnut 6 ай бұрын

@TRAyres 2 ай бұрын

I can't get the damn intake off. I think something's still holding it in... where should I be looking?

@Motorcarnut 2 ай бұрын

Yes there is an aluminum support bar that goes from the throttle body to the block, older ones have it newer ones don’t.

@TRAyres 2 ай бұрын

@@Motorcarnut That was it; that triple square came in handy. Thank you!

@Motorcarnut 2 ай бұрын

No problem! Sorry about that I will have to update the video description.

@dra.milagrosgutierrezdeher5620 Жыл бұрын

Hi your video was excellent but please is it possible to translate to Spanish ? Thank you for your friendship

@Motorcarnut Жыл бұрын

Thanks, sorry I wouldn’t know how to do that and I don’t speak the language.

@unprofessionalmechanic8466 Жыл бұрын

It is longtitudal VS transeverse. All Audis except A3 ant TT get longtitudal engine placement. :)

@Motorcarnut Жыл бұрын

Yeah it’s the same engine just put in the vehicle a different way.

@ivanvega2821 9 ай бұрын

Hey friend! Another quick question. Where did you get that new cylinder head you installed on this vehicle?

@Motorcarnut 9 ай бұрын

You can get them at a salvage yard or on eBay etc.

@ivanvega2821 9 ай бұрын

@@Motorcarnut have you had any experience with the Power Torque remanufactured complete heads from Ol Reilly?

@Motorcarnut 9 ай бұрын

@ivanvega2821 No I haven’t, sorry.

@ivanvega2821 9 ай бұрын

@@Motorcarnut when you mentioned taking off the turbo bracket at the bottom (held my the two M10s) you day to pry it away from the block with a pry bar. Do you have to actually see the becket bend away from the block? Or just pry it so loosen it up a bit?

@Motorcarnut 9 ай бұрын

@ivanvega2821 Good question. The reason why is when you remove the exhaust manifold you have tilt it back and up to get it off the lip on the cylinder head.

@ivanvega2821 9 ай бұрын

What’s the importance to have the pistons a little bit lower than TDC when installing cams in?

@Motorcarnut 9 ай бұрын

So you don’t bent a valve when the timing is not set up yet. If the pistons are not at TDC this won’t happen.

@ivanvega2821 9 ай бұрын

@@Motorcarnut i have officially completely a cylinder head install with the help of your video. I have rotated the engine several times and have confirmed time. Now, I have to install intake manifold and injectors.

@Motorcarnut 9 ай бұрын

Awesome! Keep me posted when it's running.

@ivanvega2821 9 ай бұрын

@@Motorcarnut I am almost done. Im at the point where I have to push the turbo manifold back into its spot. I’m not able to get it into its “cubby” area or little cut away area… I’m able to push it towards the head but it doesn’t fall into place like you mention. Any suggestions?

@Motorcarnut 9 ай бұрын

@ivanvega2821 It will, just push it towards the head and give it a little tap with a mallet, it will drop in

@ivanvega2821 9 ай бұрын

Hey friend! It’s me AGAIN! So I’m having a strange issue with my 2009 Tiguan after the head install. So everything seems to work perfectly fine but for some off reason. It keeps destroying the oil pressure valve (the cylinder thing inside the intake valve that’s controlled by the magnet). I have installed 2 used OEM from the junk yard and it keeps ruining them. This 3rd time I ordered one by autozone and it was brand new from Dorman manufacture. It looked like pretty good quality but it also got destroyed. It seems like the oil pressure valve keeps building to much pressure or something and getting destroyed. Any suggestions are always appreciated!

@Motorcarnut 9 ай бұрын

Ok, did you replace the cam bridge? It has an oil control ball with that filter screen that keeps ripping? This will cause that problem, however the used ones will fail as well and the doorman one are not good quality. A new OEM one is the way to go. It’s probably misfiring and long crank time when it fails right?

@ivanvega2821 9 ай бұрын

@@Motorcarnut I didn’t replace the cam bridge, I did find the ripped screen on the cylinder head thankfully. I ended up taking off the round cap off the cam bridge as you mentioned on your video. I just installed another Dorman VVT valve. Hopefully this one will last longer than a day… it just seems like a strange issue. If it destroys it again. Going to take off the upper time cover and replace the cam bridge abs VVT oil valve as well. To add to the issues. The Tiguan is also leaking rain water from the roof I guess. Went to the car wash and my driver side floor was soaked 😆 never a dull moment with this thing.

@ivanvega2821 9 ай бұрын

@@Motorcarnut correct, it misfired and sounds like a tractor. Still drives but it sounds awful. Going to take off cam bridge and inspect it. Anything specific to look for when I have the cam bridge off? Also, I know that VW started to make the cam bridges a little different. Will the newer revised part fit on the gen 1 EA888 motor??

@Motorcarnut 9 ай бұрын

@ivanvega2821 not sure, what I do is check the vw parts site and see if your engine is listed under that part and if it is your good to go.

@ivanvega2821 9 ай бұрын

@@Motorcarnut well, the cam bridge ball and spring are all broken. I found the spring but the ball is no where to be found. I’m afraid I’m going to have to pull the lower time cover and maybe the oil pan to search… and destroy. 😂

@uglybutwhocares4469 Жыл бұрын

You wouldnt want to stop by and pull my engine out for me would ya. I was told it has no compression by my mechanic who also went on to say he hates working on vw. Its been sitting in my lot for 2 years. Id love to get it running again. At this point id rather yank it out and put another in

@Motorcarnut Жыл бұрын

If he hates working for a living regardless of vehicle you should a better mechanic.

@kyleohlson9313 6 ай бұрын

I have a timing chain kit and special tool kit for it. What other parts would I need. Also, how long would you say something like this takes for an average DIYer. I have done misc repairs before, injectors, head gaskets, exhaust manifolds, etc… but nothing this in depth.

@Motorcarnut 6 ай бұрын

You should be able to do it in a weekend no problem. You will need the spline drive socket for the head bolts

@blindabinda1234 8 ай бұрын

Do you just replace the valves yourself?

@Motorcarnut 8 ай бұрын

You can if you are handy. I have many videos showing you how.

@blindabinda1234 8 ай бұрын

@@Motorcarnut does it typically mess up the guides on these cars?

@Motorcarnut 8 ай бұрын

@blindabinda1234 No

@te71se Ай бұрын

all that work to fix up the cylinder head but you're reusing the old chain and guides? it's the old style of chain which is susceptible to stretch (which is probably why the original tensioner failed as it had to overextend far). The new revised style of chain has the links arranged differently and is meant to last longer.

@Motorcarnut Ай бұрын

Video is about cylinder head removal and instal, not what parts to use.