Component Speaker Installation

No video

Component Speaker Installation | AnthonyJ350

Рет қаралды 858,933

Күн бұрын

Get better sound and imaging! In this video I show you the basics to installing component speakers and things you should consider when doing the job.
There are several ways to installing component speakers and location to where the cross overs go. This video is showing the easiest way for this particular vehicle because it already has factory locations for the tweeters.
Vehicle: 2008 Chevrolet Silverado
Product: MTX Component Speakers
#Speakers #Music #SpeakerInstall #ComponentSpeakers
Subscribe for more automative tips!: bit.ly/sub2anthonyJ350
Watch my most popular uploads!: bit.ly/anthonyJ350howto
Website: gofasthavefun.ca
Instagram: / anthonyj350
Twitter: / anthonyj350
Facebook: / aj350
Shop: www.amazon.com/shop/anthonyj350
Music available - www.jinglepunks.com & www.epidemicsound.com
About AnthonyJ350
I am a Mobile Electronics Certified Professional 12 Volt Installer (MECP Certified), Business Management Graduate (KPU), with a Professional Driver's License and a genuine automotive enthusiast who loves working on vehicles and I want to share my experiences with you. The goal is to help other people who can hopefully learn from my unique outlook towards vehicles, experiences and working practices.
Please feel free to ask questions or give feedback either in the comments or e-mail me.
New videos every week.
Please check out official web site (www.gofasthavefun.ca) for our disclaimer as we are not professional mechanics but experienced automotive enthusiasts sharing our experiences and providing entertainment content.
Go Fast Have Fun provides the content in this video, for information and entertainment purposes only.
The information in this Video presents guidelines to help vehicle enthusiasts modify or repair their vehicles and to demonstrate what car culture is all about. Go Fast Have Fun make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the Video or the information, products, services, or related graphics contained on the Video for any purpose. Any reliance you place on such information is therefore strictly at your own risk. Nothing presented should be relied upon you for your modification or repair plans for your vehicle and is not in any way professional mechanical advice.
Go Fast Have Fun strongly recommends you consult with a professional automobile mechanic to ensure that any modification or repair plans for your vehicle are appropriate for your vehicle.
In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of, or in connection with, the use of this Video and the information presented within it.
Go Fast have Fun
Canada
Component Speaker Installation | AnthonyJ350
• Component Speaker Inst...
ANTHONYJ350
/ anthonyj350

Пікірлер: 362

@lucasornelas6113 4 жыл бұрын

Most helpful useful video I have watched so far thank you Anthony !!!!

@AnthonyJ350 4 жыл бұрын

Glad to hear it helped!

@AnthonyJ350 6 жыл бұрын

To see the difference between Component & Coaxial speakers, watch here: kzfaq.info/get/bejne/hLiDn8-H1M_acnk.html

@AnthonyJ350 11 жыл бұрын

I really like JL Audio speakers right now. Their TR line up is probably one of the best bang for your buck speakers you can get, especially since you're adding a sub.

@KlutchCinemaHD 12 жыл бұрын

Amazing quality video, you explain a lot and you explain it very well. Its about time someone actually does this. Thanks!

@DreaminAccord 9 жыл бұрын

Great How-To vid Anthony *thumbs up* It's been a few years since I had to install component speakers in a vehicle and this was an easy to follow refresher - thanks man!

@AnthonyJ350 9 жыл бұрын

Glad it helped you.

@AnthonyJ350 11 жыл бұрын

Pioneer and Infinity make some nice speakers.

@alienUAE 11 жыл бұрын

thanks... you just helped me out on choosing the speakers for my car. I will definitely go for component speakers. Now my plan is to install 6.5" component speaker in a very similar way to yours in the front and 6x9 in the back doors with an AMP. I hope I will be satisfied with this set up since I don't have a place for sub. :)

@noahkb80 4 жыл бұрын

Neat little trick to run wire through boot. Go to hardware store and cut you about a foot or foot and a half of some tubing. Just cheap ol regular stuff you may see in some plumbing or a fish tank or just whatever. Just want it to be bendable but not to the point it will fold over easily, but can work it around turns. Run it through the boot first , then just sliiiiiide the wire right through. Works like a charm. I actually pulled the new wire I ran about a week after and got some black tubing and cut the length more precise, and just left it there with wire in it. Just an added level of protection

@AnthonyJ350 4 жыл бұрын

Thanks for the tip!

@edgarcobrabird1352 12 жыл бұрын

nice video. Thanks for the generosity. i can now customize my jeep. Keep up the good work!

@AnthonyJ350 12 жыл бұрын

On a component set up, yes you should hook up the amp to the cross over.

@gangsterelmoman 9 жыл бұрын

wish you would have shown how to run the wire through the door jams

@to3634 4 жыл бұрын

Okay

@williebeaty 11 жыл бұрын

awesome. i'm considering changing out the stock speakers in my truck (2012 silverado crew cab, similar to this truck) once i get a little money. i did in my last truck and it made a big difference

@AnthonyJ350 11 жыл бұрын

Oh ya for sure. If you want to be technical, round speakers reproduce sound more accurately than oval speakers. So switching from 4x6" to 4" is totally cool.

@sallopez1562 12 жыл бұрын

much needed help. thank you.

@AnthonyJ350 12 жыл бұрын

I agree with that. In a perfect setup you don't want to do that. These locations are where the manufacturer has placed them in this video. I also have a similar setup, but with two 10's in the back and tuning it's very hard to tell.

@SenorFusion12 12 жыл бұрын

Definitely learned a lot, thanks for the tip on the tweeter settings!

@AnthonyJ350 4 жыл бұрын

Thanks for watching!

@DaytonCarCare 11 жыл бұрын

Good info. Thanks for uploading.

@AnthonyJ350 11 жыл бұрын

Ya I've worked with Polk, they make really good speakers.

@AnthonyJ350 12 жыл бұрын

You can run a hi-low adapter. This will convert the signal from the speaker outputs off the factory head unit to a low level so the amp can re-amplify the signal properly. Some aftermarket amps have this feature built in. You can pick up those parts at any local install shop.

@terrenceconnor9010 11 жыл бұрын

Really helpful, thanks

@EM8844 5 жыл бұрын

I just cant find a video that explains such a simple thing as how do you actually connect a crossover to an amp or car radio. The crossover takes a "stripped" cable yet radio or amp has rca output

@AnthonyJ350 4 жыл бұрын

Speaker outputs of the headunit or the amplifier.

@AnthonyJ350 11 жыл бұрын

Thank you!

@nickiticki 11 жыл бұрын

Thanks very much. Much appreciated.

@Gerace1010 10 жыл бұрын

Nice video. Very straight forward.

@AnthonyJ350 9 жыл бұрын

Thanks!

@AnthonyJ350 12 жыл бұрын

Ya man, it's a lot of fun :)

@ryanbaumer9029 11 жыл бұрын

great video, good pointers, thanks! I have a 2007 gmc sierra classic with factory tweets and 6.5 mids in the doors... do u know if they come from the factory with a crossover?

@AnthonyJ350 12 жыл бұрын

Thanks!

@MDI.PHOTOGRAPHY828 8 жыл бұрын

I installed the new set up a while back. brainstorming new designs

@AnthonyJ350 4 жыл бұрын

Nice!

@NabilRouissi 12 жыл бұрын

Thank you so much. just one question. Is it fine to connect the amp to the crossover than to the speakers ?

@AnthonyJ350 11 жыл бұрын

Ya it might be crossed over at the amp if there's one or something. I'd use the aftermarket cross over because typically it's a better quality product. But you must have a full range signal.

@AnthonyJ350 11 жыл бұрын

I think I've only installed coaxials in the rear of those trucks honestly. You'd have to make a hole in the door panel to fit the tweeter. Ever consider installing a coaxial speaker with a directional tweeter? Also I'd build plates to mount the speakers helping them seal better and give the speaker a more solid foundation.

@AnthonyJ350 11 жыл бұрын

For some people it does. It really depends on the user, because I find everyone's hearing and expectations are different. I usually set it in the middle.

@davidsanford2542 5 жыл бұрын

Great explanation.

@AnthonyJ350 4 жыл бұрын

Thank you!

@AnthonyJ350 11 жыл бұрын

Aftermarket speakers are designed to be run with an amplifier. It's possible your new aftermarket components require more nominal power (rms wattage) than what your head unit is putting out. I'd recommend installing a 4 channel to give you the power you need.

@StealthyyyHD 10 жыл бұрын

Cheers for this tutorial

@AnthonyJ350 9 жыл бұрын

Glad it was able to help you.

@kaunaoa 9 жыл бұрын

Nice vid. Did the components set up and it sounds great with the tweeter on the pillar I'm not sure if it's actually bouncing of the windshield but definitely sounds great I have coaxles set up in my truck and wanted to try something different on my chevy van I'm glad I did and it's working fine. Thanks

@AnthonyJ350 9 жыл бұрын

Niice! Glad you're enjoying your tunes.

@Sdtukla 11 жыл бұрын

Thanks Anthony, ur upload is quite informative. I'm about to buy Sony component speakers. It includes 4 6'' woofers, 4 1'' tweeters, 4 cross overs and all speakers will be in the doors, my question is will I need 1 or 2 amplifiers and how many channels should the amplifiers have?

@AnthonyJ350 11 жыл бұрын

You can run new wires to the speakers, or use the factory wiring, wiring the amp into the factory wires that run to the speakers.

@AnthonyJ350 11 жыл бұрын

I have a similar truck. That truck comes with 4X6 speakers all around. Did you ever consider keeping the dash speakers then deleting the rear and installing 6 1/2 speakers into the door?

@sumaran72 12 жыл бұрын

love the windshield theory thanks for posting,by the way what model are those mtx components?

@AnthonyJ350 12 жыл бұрын

You can try ebay or something for passive crossovers and tweets. I'm a little unclear on the first part of your question. Like what do you use to make the actual connection?

@viewerone 10 жыл бұрын

Solid video!

@AnthonyJ350 9 жыл бұрын

Thanks!

@AnthonyJ350 12 жыл бұрын

Some speakers like Infinity already run at a 2OHM load. How are you wiring it exactly?

@TXGREASER1 10 жыл бұрын

Thanx for the info nice work

@AnthonyJ350 9 жыл бұрын

Thank you!

@AnthonyJ350 12 жыл бұрын

Running a passive cross over is preferred because it filters the appropriate frequencies to the tweeter and the woofer. You could just buy some capacitors from your local electronic store and run them inline on the positive line for those extra tweeters. That's all the entry level component setups use, they'll eliminate the bass. Or better check on ebay for some cross overs.

@ortizcruzenterprise 11 жыл бұрын

Yes it did thank you now I know how

@AnthonyJ350 11 жыл бұрын

You would tap into the speaker outputs off the deck. You'll be able to tap into all 4 outputs that way you maintain fade and balance. If they're in the rear deck I would just put in good quality 6X9's. If you're putting in a sub, buy or build adapters and put in 6 1/2". I'd get a 5 channel amp at that point.

@scoss2 11 жыл бұрын

On my amp I've got my x overs for front set to HPF. Rear (sub) set to LPF. Question, I've heard it's recommended you set the amp to HPF for comps. But how do my woofers get the mids?

@AnthonyJ350 11 жыл бұрын

For imaging yes. Otherwise they tend to have the same build as their coaxial counterpart, you're comparing speakers of the same model.

@4WheelKid 11 жыл бұрын

i like where you put the tweeters, i think thats where im going to put mine

@nickiticki 11 жыл бұрын

ive got an 11 avenger. tweeters up in the dash as well. Is there a need to install tweeters in the back somewhere or do you just install the two in the front? Also im keeping my stock deck so would i need a line out converter for the front and back? i already have one installed in the rear from subwoofers i used to have. will be installing an amp to power my speakers. Thanks

@AnthonyJ350 11 жыл бұрын

I didn't use the factory tweeter wire in this application because I got "full range" signal in the door and I wanted to utilize the provided crossover.

@carloslivinloud 7 жыл бұрын

I still don't get how to wire it like the cables coming from the radio to the crossover

@kuba7329 7 жыл бұрын

Will a Kenwood head unit 4 x 22 RMS be enough to power both front and rear component speakers?

@Alex-mu8lv 6 жыл бұрын

What if your car already has factory tweeters meaning there are already 2 seperate sets of speaker wires? Which one do you use?

@TheHoboWithAShotgun 5 жыл бұрын

U connect the the 2 wires of the speaker from original speaker into crossover INPUT then from OUTPUT of crossover to speaker

@er-zb1jy 4 жыл бұрын

@@TheHoboWithAShotgun thank you! thats what i wanted to see in the video

@TheHoboWithAShotgun 4 жыл бұрын

e r NP glad to help

@AvoKupelian 7 жыл бұрын

I got an amazing deal on Sony Coax Speakers, but my car has a component setup, I thought about converting it into a component, but I have no screw behind my sticker. I guess I could cut the tweeter off and make it work that way. Do you think I should do that or just install coax in my doors?

@AnthonyJ350 11 жыл бұрын

Yes, they use a little more power to run compared to a coaxial but yes you can.

@AnthonyJ350 11 жыл бұрын

If you're running an aftermarket amp then yes, hook it up to the speaker outputs of the amp.

@sn0wboardfreak 11 жыл бұрын

good video

@redlinebiker89 11 жыл бұрын

sweet, thanks.. I am picking up my component system tomorrow morning so yah! Next is a new receiver..Think I will just go with a digital audio receiver instead of cd..

@riklyn6769 12 жыл бұрын

maybe i missed it but what wire goes to the -3db? Great video...thx

@AnthonyJ350 11 жыл бұрын

Depends on your vehicle's set up. Sometimes it's just a little panel if you have factory tweets.

@blackrosetiger13 11 жыл бұрын

Depending how far you are Monster Sound in Winter Haven does excellent work

@AnthonyJ350 11 жыл бұрын

These are just better. Better design and better materials to give you better sound. You can install these in the rear as well and it'll definitely sound good.

@AnthonyJ350 11 жыл бұрын

I suppose you could, buy why do you want to. The typical aftermarket speaker runs at ohms so you would be running at 8 ohms which would make your system very quiet.

@AnthonyJ350 11 жыл бұрын

Did you car come with a premium amplified system?

@noahkb80 4 жыл бұрын

I have the same truck, and actually if you open the door, on both sides of the dash that are hidden when the doors are closed, are pop off panels, where the fuse box is on drivers side, theres a perfect little spot to mount them. And it just so happens that's where the speaker wires from the head unit run to side by side, then diverge , one to the tweeter, one into the door. Its about as perfect as it gets if you want to use factory wires

@AnthonyJ350 4 жыл бұрын

Great tip!

@binaryman96 11 жыл бұрын

Yea I saw that, just want sure if there was another type of glue or adhesive to install to the pre-existing tweeter pod mount. Thanks for the info though

@AnthonyJ350 11 жыл бұрын

They would have to come with some type of crossover for the factory tweeter to play properly. I don't know what they use or where it's located though. It's probably just a small cap ran inline somewhere.

@Icel4nd3r 10 жыл бұрын

Hi, i have a question, my car allready have tweeters (small speaker atleast) on the colum on the front window, but wondering can i connect the new tweeters to the cable on colum? or must i use the crossover-box from the "main speaker cable" from the head unit?

@AnthonyJ350 11 жыл бұрын

In this application power is from the speaker outputs from the factory head unit.

@asimchoudhry8775 9 жыл бұрын

so the wiring for the factory tweeter, you just left that loose right?

@jaycris1980 6 жыл бұрын

Your explanation of the speakers is good. The picture is clear as well as the installation on panels. The problem is you didn't explain how to run the wires and which wire goes where.

@AnthonyJ350 Жыл бұрын

Thanks for the feedback

@AnthonyJ350 11 жыл бұрын

That's correct. That way it's reversible if need be.

@Mikeallen2112 11 жыл бұрын

Did you run new wire from the head unit? And is an amp necessary for such an application? Or is the head unit supply good enough?

@donatorusso6410 10 жыл бұрын

I am wondering... Do you send the factory speaker wire directly to the input of the cross over?

@TheCheetahang 10 жыл бұрын

Hi I have install a 5.25 components speaker in my rear door but my both tweeters r not working.can I replace any other brand tweeter or it has to be same one.thanks

@AnthonyJ350 11 жыл бұрын

Yes you still will need to install the crossover.

@AnthonyJ350 12 жыл бұрын

Positive output for the tweeter.

@MarcelloTheBandit 11 жыл бұрын

In my experience with GM trucks like this, I have just cut the adapter off the stock speaker and put it on the new ones. What are your views on doing it that way?

@AnthonyJ350 11 жыл бұрын

As long as the speaker is mounted securely and you clear the window you should be good.

@AnthonyJ350 11 жыл бұрын

No you can use just head unit power. They sound better with an amp though.

@AnthonyJ350 12 жыл бұрын

You just use the positive and negative speaker inputs from either the head unit or an amplifier.

@arch417powersports 11 жыл бұрын

What gauge of wire do you use for these door speakers and tweeters?

@Kole208 11 жыл бұрын

hey one more question, my dad thinks that buying a sbwoofer and amp kit would be easir to install than buying the sub and amp seprate. is that true? wouldent it just be the same work?

@CHILLDOWNPLEASE 12 жыл бұрын

what kind of glue do you use nice vidio thanks!!

@AnthonyJ350 11 жыл бұрын

It's about the same amount of work. The only difference is the amp in an amp and sub combo is already mounted to the enclosure.

@toufic1995 11 жыл бұрын

whats the difference between the factory speakers that already have tweeter and the after market ones and can these be installed in the rear doors too or is it too much

@Kole208 11 жыл бұрын

would the combo come with all the wires you need though, because im lost when it comes to that. idk what wires i need.

@JRZrEeFerIsdS 11 жыл бұрын

I just purchased a couple 6 1/2 components. And a 4 channel amp. I dont need to install a croosover then right??

@MrLucious50 11 жыл бұрын

wondering if you ever installed component speakers in a 2000 GMC Yukon rear doors.........or any suggestions

@binaryman96 11 жыл бұрын

Just curious if you dont use the hot glue what other method would there be in attaching the tweeter to the factory mount?

@valentinsarmagal 8 жыл бұрын

nice vid, some problems with the lightning though

@AnthonyJ350 12 жыл бұрын

Rears are set pretty low. Are you tuning off an amplifier? Try 80Hz for the 6.5" speakers.

@Kole208 11 жыл бұрын

is their any other good line up of speakers you would recomend because jl audio dosent have a oval 6inch speaker or 6 1/2, they only have round ones and round ones wouldent fit.

@nickiticki 11 жыл бұрын

yea the speakers in the back are not in the doors, they are behind your head, so i guess you call that the rear deck. As for the line out converter i am familiar with but with the PAC one that has 4 pre-outs, does that mean i will have to tap into the front and rear speakers into 1 converter? Also, would i need to tap anything into the tweeters or is that not necessary? Thanks for the information. Much appreciated

@mast3rbug 11 жыл бұрын

I have a Jimmy 2002 with stock tweeter option in the place of front 4x6 and main speaker in the door. I don't want to feel the hi sounds come from up and the voice sound come from the doors... Do you have this effect with a setup like that or the sounds is completely mixed and really transparent? If not, Can I have great HI performance with quality coaxoal in the door and quality 6x9 in the back? What your preference? Thanks!

@Kole208 11 жыл бұрын

what are the best 6 inch speakers to get then? im also going to have a 10 inch sub in the back.

@thefeistywombat 11 жыл бұрын

you know you could use the factory speaker mounts in the doors, all you have to do is peel the old speaker out because it is glued in to that big plastic piece. its much easier and saves money that u may have to use on extra parts.

@AnthonyJ350 11 жыл бұрын

They come with mounting hardware if you want to have the tweeter exposed so you can clamp it to the panel as well. People have different ways of doing it.

@spikz4213 9 жыл бұрын

Just one doubt. Is it necessary to amplify the input with an amplifier for better sound quality ? Like sending the output of the head unit to an amplifier and then taking that output and sending it to the crossover.