Eastfield College Automotive www.eastfieldcollege.edu/cd/c... Toyota T-TEN T-TEN.com Bishops International www.bishopengine.com/transmiss...
Пікірлер: 20
@didloful3 жыл бұрын
Thanks. I got a volvo and mine was frozen in neutral. When I got the transmission out I couldn't push the slave in. This is the only video that shows how easily it the slave can be pushed in. Mine unfortunately was frozen. Thanks.
@westsidedavie Жыл бұрын
Just did the clutxh,dual flywheel and concentric slave on my 08 escape .I also have a 98 honda accord I did clutch and flywheel on but them Hondas have external slaves.
@Nibiru9993 жыл бұрын
thanks :) my car clutch pedal just died so i wanted to know what might be happening
@user-hq7ff6kx6b2 жыл бұрын
Hello, thanks for the video. I have Fiat Bravo 2 1.6 multijet 105hp. From 1-2 weeks I have an issue with the clutch - when I am going on first and reverse gear the car is vibrating and annoying rasping sound is heard on the front of the car. Sometimes I am not even able to shift the gears and when I turn off the car and pump the clutch and then the car start shifting and driving off without vibrations. Could it be a problem with the clutch release bearing? Or because of old brake fluid and air in the system? Thanks in advance!
@tsriftsal35815 ай бұрын
So any seals that would fail or bearing failure on a non concentric slave would still require removal of the transmission it seems. Is that correct? Seems like leaking fluid would damage the "slave cylinder" bearing on a concentric slave as easily as it would on an external slave cylinder with a fork.
@douglaskruse62422 ай бұрын
I have the same transmission and I just replaced everything from the flywheel to the transmission and i can't get full clutch pressure. Any ideas?
@robertbrandywine Жыл бұрын
What does the piston look like? Is it possible to see it or is it completely surrounded? What, exactly does it press on?
@karenmaeledda92902 жыл бұрын
Is ta csc is leaking brake fluid under the transmission sir?
@fredstein542911 ай бұрын
i have that exact tranny in my 95 f150, just got a new slave to install, but i think its defective as it cant be compressed by hand .. should it be able to like my old one or should it be stiff until actuated after install? appreciate these videos muchly!..thanks
@micp012 жыл бұрын
Hi great video thanks. can you show how to check the slave cylinder when its out in your hand? I have the gearbox out and I put a finger on the in pipe and press the bearing in and then it show resistens. Im not sure now if i did this for nothing😂 I have change the headcylinder first. So? Now im stuck
@outofthebox502 жыл бұрын
The most common issue is leaks. Sounds like yours moves freely. If it doesn't look like it was leaking, you should be good.
@josefigueroa50882 жыл бұрын
Should the slave be dry all throughout? Mine has alittle bit of fluid behind the surface that pushes on the pressure plate.
@outofthebox502 жыл бұрын
If there is enough fluid to drip, it should probably be replaced.
@fullproof1002 жыл бұрын
Sticking clutch pedal....can this internal slave be guilty of not fully returning?
@outofthebox502 жыл бұрын
Possibly. More likely to be air in the system which could come from the slave or the master. Check the firewall for trickling fluid or bubbling paint and check bell housing for dripping fluid.
@fullproof1002 жыл бұрын
@@outofthebox50 Thank you👍...told garage who said they bled it but still doing it 10% of time 🙁👍
@jamsocrane3 жыл бұрын
my new slave cylinder will not move In and out like this one. Have a comment?
@jamsocrane3 жыл бұрын
Hey just force the spring and now Its active moving.I've been having a big struggle getting this transmission back on. Maybe this was the problem.
@fredstein542911 ай бұрын
@@jamsocrane me too.. exactly the same issue.. did you figure it out?