@MrRobMetal 6 жыл бұрын
heres a tip for ya. an E34 steeringjoint fits without modding, and is solid from the factory ;)
@TheKingduffy138 3 жыл бұрын
Whats the part number? there are many part numbers for it so idk if theres any difference
@jeremyabbott2829 4 жыл бұрын
To anyone replacing this, make sure to remove the bolts completely. There is a grove on the spine that the bolt rests against. It will prevent you from removing the coupler no matter how much you bang on it.
@carlosorozco4786 7 жыл бұрын
That's a great DIY video! I like how you added in the tools you need and alternative options to remove the stock steering coupler! I agree with what you said about enlarging the holes for the bolts. You don't want to take too much material that will weaken the area. Definitely don't want any fatigue or cracks! Looking forward to the next video!
@Pawinning 7 жыл бұрын
+Carlos Orozco hey thanks man! I'm glad you enjoyed the video and agree with me! 🙏
@robertfontaine3650 10 күн бұрын
The bigger question is how this compares to a new rubber bushing rather than comparing it to a 20 years dead piece of rubber. Whether poly is adding unnecessary vibration to the steering.
@TedwardDrives 7 жыл бұрын
dat steering wheel alignment haha. love it
@Pawinning 7 жыл бұрын
+Tedward oh yeah 😂. Calls for another diy!
@r_ez4608 7 жыл бұрын
The e36 sounds so good man. -Rob
@thomasbugler958 2 жыл бұрын
Right now I am fighting to put the joint on
@becomematrix 6 жыл бұрын
Thanks for this video. I inspected mine and it was just as soggy as yours. I got a solid e34 coupler instead because shipping rates to europe are expensive.
@Pawinning 6 жыл бұрын
+Captain Crook you're welcome! And that sucks shipping is expensive, but I'm glad the e34 solid coupler worked for you as well!
@kaseytreadwell1 6 жыл бұрын
Awesome video condor rocks.
@Pawinning 6 жыл бұрын
+kasey treadwell thank you!
@user-bd8wy4ld4b 6 жыл бұрын
I liked this video before I even seen it cuz I knew it was going to be 🔥
@Pawinning 6 жыл бұрын
More content to come :)!
@IgnitionTube 7 жыл бұрын
Anotha JUAN!
@Pawinning 7 жыл бұрын
+IgnitionTube 🍄🌼 🐱
@C7mb 7 жыл бұрын
love the air freshener 😉
@Pawinning 7 жыл бұрын
+C7mb thank you!
@jcfinch4389 7 жыл бұрын
helped me alot. just earned another subscriber
@Pawinning 7 жыл бұрын
+Jc Finch thank you for the sub!
@tylertran93nsx 4 жыл бұрын
Need help, just did my with factory coupling, but I had the same off center steering wheel like you, about 2 to 3 inch towards the right, what did you do to fix it? I would hate to pull that thing off again... it was a pain.
@lucase3047 6 жыл бұрын
@pawinning Am i right to think that it doesnt matter if u mark up the coupler like you did with the sharpy? I guess it only matters if u move the steering wheel while the couple is off ... amirite?
@Pawinning 6 жыл бұрын
Yes you’re right, but bear in mind that separating the coupler allows the steering wheel to spin freely. Being off a couple teeth on the rack can translate to the wheel being very off centered
@MonoLucas123 6 жыл бұрын
Pawinning ah, so might be better to lock the steering wheel with a aligning locker or something. I wanna upgrade mine too a poly also... Good to see this diy.
@julianmcalister3247 5 жыл бұрын
What up man. Trying to have everything ready for when mine gets here is the reason for the question. Anyway, what size drill bit did you use to make the holes bigger for the bolts it came with? Also, how did you end up tightening the bolt that was covered by the couple?
@msinclaircorp4571 3 жыл бұрын
Thanks!!!
@trololazore 2 жыл бұрын
Your the GOAT
@fstlnj29 6 жыл бұрын
Nice video. How do you like the solid engine mounts?
@Pawinning 6 жыл бұрын
Thank you. Love them still 👌😎
@SuperLuis722 7 жыл бұрын
Have you tried any other bushings from them?
@Pawinning 7 жыл бұрын
+SuperLuis722 yes! I have their full "sleeper solid bushings package". Video content can be found on IgnitionTube!
@matthewpistritto2033 5 жыл бұрын
review of this now that youve been used too it? just ordered one for my e46
@Pawinning 5 жыл бұрын
Actually since then condor has created an entire shaft replacement that eliminated the need for this coupler. I'd recommend that over this product due to a superior design 👌
@danielplumley2649 7 жыл бұрын
👌🏼👌🏼👍🏼
@fitnesspoint2006 2 жыл бұрын
no saggy glove box door
@orah1785 3 жыл бұрын
Condor speed sent me the wrong product twice , no note just saying
@car_lows29 7 жыл бұрын
first 😉 lol 😂
Pawinning
Рет қаралды 205 М.
E46 Power steering coupler upgrade - The best Polyurethane guibo modification! BMW 330ci race build.
Tenza Motorsports
Рет қаралды 19 М.
Skadonk
Рет қаралды 66 М.
Bad E30
Рет қаралды 74 М.