This is a quick easy way to convert a 4l80 to work with a 4wd set up! tools needed -hand tools -cut off wheel -flapper disk -grinder -tape measure.
Пікірлер: 49
@dianepirtle53327 ай бұрын
Why did you cut anything off the t-case you only needed to shorten the transmission output shaft
@kylemilford59682 ай бұрын
He wanted to maintain maximum overlap between the two for strength OE has 2 inch overlap, if he cut it all from the output he would be left with under 2 inches of mating surface
@zyrintotary5204 Жыл бұрын
This worked thank you we were scared at first cause it wouldn’t start then towed it to shop and they said it was a knock sensor or something like that and they changed it .. truck fired right up but wouldn’t move so we doubted it worked… then we forgot it needed fluid so we filled her up and she drives normal again… thank you
@DIRTCINEMA Жыл бұрын
Glad it worked!
@terryburnett797 Жыл бұрын
Saved me a lot money homie thanx
@diduck68782 жыл бұрын
Just cut transmission
@Keeterbob Жыл бұрын
Instead of shortening the t case. Why not take more off the shaft?
@cadmonkey928 Жыл бұрын
i was wondering that too, but i think the tcase external shaft was gonna be too long also and bottom out on the trans splines where they stop and go to a cone shape. you can kinda see it at 7:37 when he puts them together without the 4wd tail spacer. i think he didnt explain that part well?
@jtp6822 жыл бұрын
hi there, can you say what transfer case that is and what year 4l80 it is? thank you.
@ygbinc37752 жыл бұрын
Basically, If I mod a 4L80e to fit a NP208 transfer case will it be possible to use it with a NP205 transfer case ?
@sirkrow71182 жыл бұрын
As long is it’s the same spine count and bolt pattern. I’d do a little research as to what the measurements r like between the l80 output shaft and tcase input length are. As long as they r the same or VERY close, I’d imagine it would work fine
@jorgebribiescas43154 ай бұрын
Hola funciona también en una transmisión estándar del 2002 se puede convertir a 4x4
@dieselmechanic98242 жыл бұрын
Got a new subscriber. Good video
@DIRTCINEMA2 жыл бұрын
Thanks dude!
@dieselmechanic98242 жыл бұрын
@@DIRTCINEMA how is it working out for you
@DIRTCINEMA2 жыл бұрын
@@dieselmechanic9824 so far so good! Lots of street miles and desert miles on her so far!
@kylemilford59682 ай бұрын
Curious why you didn't just swap the output shaft cdom.the 4wd in as it's already shorter?
@cade2367Ай бұрын
Probably doesn't know how to tear apart a transmission
@FirstLast-tx3yj2 жыл бұрын
Which cars have the 4l80 that comes 4x4 stock?? The one used for drag racing with a button to switch from rwd to 4x4
@brandonheckathorn32702 жыл бұрын
93-06 chevy/gmc 2500s
@jasonlee9326 Жыл бұрын
Can convert a 4x4 700r4 to a 2x4 by changing the tail housing?
@ygbinc37752 жыл бұрын
If I’ve already cut they shaft in my 4L80e like in this video can I still adapt it to a NP205 transfer-case if I’d like to ??
@mrsteel102132 жыл бұрын
I have the same issue need a 4x4 tranny and i got the 2wd at the pick and pull . I wanted to keep the original to the engine and realized i need a 4x4 for my appication. The truck i pulled is a 2008 and wondering if a 2004 4x4 tranny fit with the 2008 computer
@DIRTCINEMA2 жыл бұрын
I'm not sure on the computer but I'm sure it will work but it should
@DownForMobbing2 жыл бұрын
You have a list of tools needed but, don't say what type of hand tools I will need for this job? Can I use your flat head screwdriver?
@DownForMobbing2 жыл бұрын
also, that is a hoodie not a shirt. just FYI.
@DIRTCINEMA2 жыл бұрын
I’m sorry berg this should be easy to figure out what hand tools are needed. But I understand if you can’t figure it out on your own. Maybe hire some one to do it for you?
@DownForMobbing2 жыл бұрын
@@DIRTCINEMA why you always so sensitive when I talk to you 🥺
@zyrintotary5204 Жыл бұрын
I wanna try this but does this work? I’m asking before I cut
@DIRTCINEMA Жыл бұрын
We’ve been driving the bronco every day since we did this!
@Mylotheblacknwhitecat4 ай бұрын
Hey would one these adapters work instead of cutting
@johnwindle6877 Жыл бұрын
Why not just change shafts?
@ratedxx11 Жыл бұрын
Because u would have to gut the whole thing out
@bryancain97322 жыл бұрын
Will this same technique work on a 4l60e?
@DIRTCINEMA2 жыл бұрын
I’m not sure. But it should
@christopherwright36102 жыл бұрын
why did you tip your hat at the end? just curious
@DIRTCINEMA2 жыл бұрын
For the ladies
@tylertruax5932 жыл бұрын
@@DIRTCINEMA niiice!
@mikeyd717 Жыл бұрын
@@DIRTCINEMA before I even looked at the replies I said to myself he better if fucking said for the sweet ladies who watch videos like this or I'm going to have to. Or idk it's just something your mother asks me to do. You'll have to ask her why. Well done sir you responded correctly. Interesting video. Im saving it in case I need it for my 2500 somewhere down the line. So did you do an LS swap in your bronco?
@DIRTCINEMA Жыл бұрын
@@mikeyd717 every lady needs a hat tip lol
@Briszy Жыл бұрын
@@DIRTCINEMAor a dick tip 😂😂
@larrycorpuz2644 Жыл бұрын
What transfercase is that?
@DIRTCINEMA Жыл бұрын
241 c
@jean-philippecaron51608 ай бұрын
Wrong. This is a bw4401. Or similar in borg warner gm series. Sure doesnt look like a new process case.
@kevincameron72082 ай бұрын
Can we confirm this. I have a BW and I am picking a 2wd 4l80e today.
@zackwhite7120 Жыл бұрын
Do you need a outputshaft seal for the 4wd ?
@DIRTCINEMA Жыл бұрын
Out put shaft tail housing yes
@zackwhite7120 Жыл бұрын
@@DIRTCINEMA so you put the seal in the 2wd trans so the t case after I cut the shaft ?