CR Touch Auto Bed Leveling Upgrade For Ender3 And Other Ender Printers No manually level printer bed

Рет қаралды 27,603

Жыл бұрын

Note: G-code is read line-by-line, so G29 needs to be on a separate line after the G28. Thanks to @andyh7537 for pointing this out.
Upgrading my ender 3 with CR touch auto leveling kit. I'm tired of manually leveling the bed after every few prints or when I move things, this suppose to reduce or completely remove the need for that.
I'm not being paid for this.
Links:
CR touch (15% discount): www.amazon.com/promocode/AN99...
Glass Bed: www.amazon.com/Creality-Upgra...
Direct drive: www.amazon.com/dp/B09NVWJYMT?...
Firmware Download: www.creality.com/pages/download
Thanks for watching. My goal is to provide fun and engaging educational content and I'm always interested to hear from you in the comment section.
Links:
Website: techspassion.com/
Instagram: / techspassion
Linkedin: / techspassion
Tiktok: / techspassion
Thingiverse: www.thingiverse.com/techspass...
Pinterest: / techspassion
Facebook: / techspassiondiy
Twitter: / techspassion
#TechsPassion
This video and information is intended for educational and entertainment purposes only. Please use at your own risk. Thank you for understanding.

Пікірлер: 179

@andyh7537 Жыл бұрын

Thank you for the fantastic step-by-step video! One note: G-code is read line-by-line, so G29 needs to be on a separate line after the G28; Home command. Cheers!

@techs.passion Жыл бұрын

Thank you for the correction, really appreciate it. Let me pin this comment as it might help someone. So far I'm not having any problems on my printer but I think you are correct. Thank you for watching :)

@patrickkelly7789 11 ай бұрын

Thank you so much I was having so much trouble trying to figure how why it wasn’t working and this fixed it

@techs.passion 11 ай бұрын

Glad it worked and thanks for watching

@Blazing_Phoenix_YouTube 11 ай бұрын

Thanks for the tip

@bob77576 7 ай бұрын

It does directly say in the manual to change "G28" to "G28G29," so the video is correct to the Instructions provided by creality. So the video is accurate to them at least

@tylerblowers7906 10 ай бұрын

Wonderful video, mine shows up tomorrow and I'll definitely be rewatching this when it's time to install! Thanks a bunch yo!

@techs.passion 10 ай бұрын

Thank you for watching. Also happy to help in case you get stuck at any point. Do not hesitate to ask. I hope it goes smooth for you.

@techs.passion 10 ай бұрын

By the way, there is a pinned comment about the code modification. I recommend you read it. Some one corrected a small miss in my video so it might save you some time by reading that pinned comment on that video.

@tylerblowers7906 10 ай бұрын

@@techs.passion already noted! Thank you!

@ahmedabdelsalam204 Жыл бұрын

Great video thank you. I really liked the motherboard fan cover as well!

@techs.passion Жыл бұрын

Glad you like it. Yes, the fan cover really useful. You can print one, I got it from Thingiverse www.thingiverse.com/thing:3155772 you can search for fan cover and see many of them. Thank you for watching :)

@invinitybox8326 Ай бұрын

This is the best Tutorial I ever watched on this topic. Thank You 🙏

@techs.passion Ай бұрын

Glad it was helpful! Thank you for your kind words and for watching :)

@invinitybox8326 Ай бұрын

@@techs.passion Just one Question, I can't find after it my files on my mini SD card so I don't know how to print them out, can you help me with this?

@techs.passion Ай бұрын

Did you format the micro SD while using it to update the firmware?

@invinitybox8326 Ай бұрын

@@techs.passion Hey, yes everything works just fine I just forgot to delete the wuestion yesterday, sorry for that. But I have an other Problem with which I was hoping you could help me out. Every time I'm trying to print sometimes out the filament won't stick to the bed, I levelled the Z offset even while it was printing but still the filament won't stick. I was wondering if you had any advice for this problem?

@techs.passion Ай бұрын

Hi there, sorry for the late response. I would say clean the bed, make sure it leveled correctly and make sure the temperature is correct for the bed and the filament. For faster reply, consider joining my discord, it's free and I'm always there. Link in the description

@LSeima Жыл бұрын

Having cr, bl or other touch do not mean you wont have to level the bed manually. You still have to do that in order to get proper prints. It only compensates small imperfections. It is crucial to make a good manual adjustment. Too bad many people think otherwise

@techs.passion Жыл бұрын

100% you still need to level the bed but less often. The rubber pads are more stable than the springs so that is one and it does account for minor difference in the corners if it happen to be. Another nice thing is if you need to change the bed from a slim bed to a thicker bed you do not have to relevel which is nice. All that said you are correct. Thank you for watching and the detailed comment.

@user-yh8mq5bf2n 2 ай бұрын

Congratulations for the video, could you put the link of the 3d model, for the fan cover? Thank you

@techs.passion 2 ай бұрын

Thank you so much, for sure, here is the link www.thingiverse.com/thing:3155772

@AndrewAHayes Жыл бұрын

I got a Creality BL Touch upgrade pack, this included the BL Touch and an ISP Programmer to flash the firmware, the kit came with a pin 27 board, the software for the ISP would not work, eventualy I realised it had Chinese Characters in the .EXE so I deleted these and then it would load, I fitted the pin 27 and the BL Touch and then realised the lid to the electronics case would no longer close with out shorting out the pin 27 so I had to take off the fan from the lid and lay it over the drivers to cool them while I printed a new electronics lid riser that I had designed in Fusion 360, I was forced to learn the parts of Fusion 360 I needed as Tinkercad was not powerful enough to design this riser lid, so eventualy I had the lid closed and the BL Touch working, but I also had to level the gantry every five or so prints as it dropped on the right hand side and the BL Touch would not compensate for such a large difference, so then it was dual leadscrews to be fitted and I then had to design a sync belt system to keep the leqadscrews in sync, it seemed Creality only ever made half an upgrade, it was at this point that I went from a Creality fan boy to a Creality Hater Boy, I had bought the Ender 2 and CR-10 and two Ender 3 machines, by the way the BL Touch firmware was faulty and I had to learn to configure Marlin firmware and compile it to get the ABL working correctly and I did a much better job on my first try than Creality had done over all the machines they had released, this made me realise Creality was just not interested in getting the best from the machine or even a correctly working basic firmware

@techs.passion Жыл бұрын

Wow that sounds like so much trouble for that upgrade, I do not blame you, I still like Creality because that is the one I'm most familiar with but open to explore if the opportunity comes. Lucky for me, the CR touch was simple enough and really easy to install and setup. Right now my Ender 3 is very well upgraded. I also bought an Ender 3 Max, remember when I mentioned that I was keeping an eye on it, the other day I got it for some discount and will make a video about that soon. I do use Tinkercad most of the time since my Fusion 360 subscription expired and I do not want to pay for it. Seems like you have so many printers, which one is your favorite? Thank you for the comment and all the details, I will pin it on this video since it is really helpful and might help others. I really appreciate the details and thanks for stopping by.

@AndrewAHayes Жыл бұрын

@@techs.passion my favourite of the Creality printers is the original Ender 2, that printer is the most reliable one I have and its also the least expensive, it just works, I can press print and just walk away from it knowing full well it will just print and complete its part, the only upgrade it has are some silcone spacers and a PEI bed, it is slow but the layer stacking is perfect, Creality hit a home run with this machine but chose to stop making it when the CR-10 and Ender 3 took off

@noobt4eguns 5 ай бұрын

Attention if you change the limit sensors must have all the same part number example 2134. I spent months to recognize it. If that sensors are different then the printer will become crazy and you will not understand from were the issue is.If they have different number the printer can't do autohome the cr touch can't work even if you pass the software with out the cr touch again will not work. I become crazy many months know and today i found the solution 🇨🇾👍🏻

@techs.passion 5 ай бұрын

Hey buddy, so you mean the end zero switches all need to be the same and basically if you change one you need to change all 3 or the 2 in the case if you have CR touch? Good to know, I never needed to change them so far but did I understood this correctly?

@noobt4eguns 5 ай бұрын

@@techs.passion no matter if you have cr touch or not. The switches must have same part number or the specific part number i think. I have issues with leveling the bed and my memory carts sometimes recognized from the printer sometimes not. Pm i need help i can't do it alone.

@techs.passion 5 ай бұрын

Good to know, thanks for the info. Yes, happy to help, join the discord, we will help you better there

@noobt4eguns 5 ай бұрын

@@techs.passion my Ender-3 don't like the cr touch ,all the sd cards i have can't save the cr touch settings . Now my printer works perfect with out the cr touch and with the normal software printing more than perfect

@techs.passion 5 ай бұрын

That's perfect but the CR touch still nice however if you are going to skip it, should still be find to be honest. As for the SD card, use the same one you used to upgrade the printer, that should work to store the settings

@steveo2737 25 күн бұрын

Yeah, I knew I saw this video before lol I followed this to a T and I have no issue with flashing the hard drive however I think i'm making this too hard. When you put the CR Touch on the ender 3, will this firmware replace the current Marlin one on there? Like my Marlin shows in the About Printer 2022 but when I load the cr touch, the firmware changes in the About printer to 2020.

@steveo2737 25 күн бұрын

Subbed since I've spent several hours on your channel in the last week and appreciate all the help you have given to the community

@techs.passion 25 күн бұрын

Yes, the CR touch firmware will replace your original firmware unless the original one you have support CR touch. I should test that when I get a chance, I think Marlin does support CR touch but don't take my word for it. Thank you so much, I'm happy to have you 😊 I think you made my 10k Happy to help, if there is anything you want to see or any feedback, I'm happy to hear it.

@steveo2737 25 күн бұрын

@@techs.passion happy to be your 10,000th subscriber!

@kevinrenner9831 13 күн бұрын

Hello, I would like to know if you can tell me what size the silicone supports are, if they are 16mm or 18mm?

@techs.passion 13 күн бұрын

Hi, I didn't measure them but. 3 of them are a bit higher than the 4th one which goes on the cable leg of the bed

@techs.passion 13 күн бұрын

Currently I'm not near the printer, I will try to measure them when I get back

@Allforthebadge 5 ай бұрын

Will the bed spacers work with Ender 3 max?

@techs.passion 5 ай бұрын

Yes, they will work. This CR touch should work with the max

@TheRealWorld198 Жыл бұрын

I have a problem, my ender three always shows no tf card. Can you tell me how to fix it? It’s brand new, there are no files other than prints, and I always eject it properly from my laptop. ( it is also formatted to the correct way) it was also working perfectly fine for my first three attempts, but then I just got the warning. And if it doesn’t show the warning, it doesn’t show a print. Thank you

@techs.passion Жыл бұрын

A few tings comes to mind, I have seen the issue also heard of it a lot. Try different MicroSD Card. Another thing is avoid large size cards, 32 GB is your max I would say. Last thing, when you bring the card back to the laptop, is it still works fine, like after the error, you take the card back to the laptop, is the card corrupted or good on the laptop? I know you said the format is correct and all that. Unfortunately, I have seen it being a motherboard issue and you would have to replace the board but I hope you do not have to go that far. Hopefully this helps, the last thing I would try is update the firmware version to something newer and if the printer not too old and if it end up being the board you can look into getting a new one from the seller. Thank you

@hayleyedwards3676 3 ай бұрын

It’ll be due to STM firmware running on a GD chip, I had the same issue, the firmware options aren’t clear on the Creality website.

@damoodarans1885 6 ай бұрын

Hi buddy, I have a ender 3 with motherboard v4.2.2 and i try to install the firmware i downloaded the firmware from same page as you but selected v4.2.2 but i dont know if it installed and when i try to check z axis its not going in negative it stops at 0 please help me and ( for note i removed z limit switch wire from motherboard too)

@damoodarans1885 6 ай бұрын

nvm i got it but it still not going down negative value

@techs.passion 6 ай бұрын

Hi, it sounds like your firmware didn't get updated, let me share with you a video that might help. kzfaq.info/get/bejne/i9Njaaid3rrMg2g.html kzfaq.info/get/bejne/hdenqNaevN2dZ6M.html

@Terror.Senpai 23 күн бұрын

I can't figure out whats wrong with my Ender 3. I've followed all the steps as shown but whenever I do Autohome once it reaches the printing base on the z axis it just keeps trying to go further down and doesnt stop and so the motor is just continuously trying to spin the rod and move the nozzle further down even though its already reached the bottom and the tip of the CR Touch is already touching the bed

@techs.passion 23 күн бұрын

Sorry to hear that you are having trouble. It sounds like it has something to do with the firmware or the offset level because it sounds like your printer is still looking for the Z switch which I'm guessing you disconnected as you should. Make sure you have the correct firmware and set the correct z offset level

@Terror.Senpai 23 күн бұрын

@@techs.passion so I actually figured out a solution. I had to take off the z switch entirely not just unplug it. Basically the arm was going down the Z axis but was still stopping at the switch since it was a physical object stopping it from actually going all the way down and touching the board with the sensor on the cr touch. Ended up having a firmware issue though and the printer kept freezing so had to switch to marlin firmware and now its working great! First print came out great other than running out of test spool before it finished lol

@techs.passion 22 күн бұрын

I'm glad you figured it out. Yes that Z switch is not needed. Thank you for the update and glad to hear it

@dakotashepherd1 6 ай бұрын

so mine didnt come with rubber pieces and mine still has the spring and it wont allow my z offset to go below 0 and wont allow the nozzle to get close enught to the bed for the paper level how do i fix this

@techs.passion 6 ай бұрын

Hi, the springs are fine, no need for the rubber. As for the below zero, make sure to disconnect the Z switch and upgrade the firmware

@dakotashepherd1 6 ай бұрын

i have removed the z switch and updated firmware still won't allow me to go below zero@@techs.passion

@dakotashepherd1 6 ай бұрын

never mind watched your other video and got it figured out!

@techs.passion 6 ай бұрын

Perfect, glad that you figured it out

@jesperlarsson3699 Жыл бұрын

A couple months ago i bought a cr touch, i tried to install it and everything went well untill it suddenly stopped working. I restarted the printer and the light was now constantly red. i tried to fix it by looking at some youtube videos but nothing worked. After a few days it stopped lighting up at all and now it does nothing. Do you have any idea on what the problem can be?

@techs.passion Жыл бұрын

Hi, sorry to hear, sounds like too much trouble. Since it's not even lighting up I'm guessing something with the power so basically I would check the cable and ensure all that connected well. Take the cable and test it own it's own, make sure the cable doesn't have any cuts. I'm guessing you can you use a multimeter or simple LED to test it out. If the cable checks out and you make sure it's connected well and still no light then it might just be the CR touch dead but sounds like a power issue is my bet guess.

@jesperlarsson3699 Жыл бұрын

@@techs.passion Thank you for fast response, I will check and see if it gets power or if its just broken.

@jesperlarsson3699 Жыл бұрын

@@techs.passion I removed the backplate and wiggled the cable while the printer was on and it started to work again, so the cable was not getting good connection, ty for your help (=

@techs.passion Жыл бұрын

Glad I was able to help, yeah it sounded like something with the cable. Hopefully it works, you might need to reset the settings and the offset, I know the software can be buggy and sometimes you just need to re enter the offset level.

@jesperlarsson3699 Жыл бұрын

@@techs.passion it si finally working!! only took like 2 months /= do i have to level the bed before every print or how often should i level it?

@hauntedwonderlandproductio1013 3 ай бұрын

I didn’t get any rubber levelers in my package???

@techs.passion 3 ай бұрын

Most of them should come with it but in your case I'm sure the springs will work just fine. It's not a big deal really but sorry to hear that you didn't get them.

@MrForegrounds Жыл бұрын

My firmware doesnt have store settings option.

@techs.passion Жыл бұрын

The only reason I can think of is the microSD card is not inserted or could be corrupted, try to format the microSD card to FAT32 and reinsert it

@icyxenon7167 2 ай бұрын

I followed the the steps all the way through everything was plugged in and the working minus the firmware installation for some reason its still loading the version 1.0.8 and not installing the latest firmware (i have a v4.2.2 board) i even attempted v4.2.7 assuming i had made a mistake on which board i had and still nothing i reformated my sd card and met all with dead ends

@techs.passion 2 ай бұрын

Sorry to hear that, I assume you got the CR touch specific firmware and unplugged the Z axis. Are you getting an error or what state are you at?

@icyxenon7167 2 ай бұрын

@@techs.passion i dont know if it was the cr touch specific (i was following your steps since we had/have the same printers) but when i replugged the power wire and turned the printer on with the firmware .bin on the tf card it would just start as if nothing changed... as if the .bin wasnt being executed i had seen on creality's website that i needed to flash my firmware but i had seen many tutorials that didnt say to flash

@techs.passion 2 ай бұрын

You are going in the right direction but you need the CR touch version of the firmware. I do mention that in the video and also I have a video on firmware. I think you just need the correct copy of the firmware. Go to the website and get the CR touch version of the firmware

@icyxenon7167 2 ай бұрын

@@techs.passioni just rewatched the video again this was my 3rd time watching and i just realized i searched for the printer on the side bar instead of under cr touch thank you brother i had been losing my mind for hours trying to figure out what i did wrong i hope you have an amazing day 🙏🙏

@techs.passion 2 ай бұрын

Glad you got it figured out, very happt to help and thank you for watching. You too, have a good day

@spray_cheese 7 ай бұрын

So why did they make it so you can’t use negative values on the v2? My nozzle is too high and 0 is still too high. I give up.

@techs.passion 7 ай бұрын

You should be able to set a negative value for the z offset. Did you upgrade your firmware? Let me try to help, no need to give up

@spray_cheese 7 ай бұрын

@@techs.passion i really appreciate you and your fast response🙏: I did upgrade my firmware. Appearance wise it all looks good so far. But I did the first autohome that leaves you with 10mm of clearance. And the lowest I can set it to is 0 on the ender 3 v2. Which also only allows full decimal point increments. So that’s making it even harder to dial it in. But either way. There’s still a good 3-4mm of space between the nozzle and the bed. My stock z switch is removed. Ive heard on some forums to add some 8 digit code to the OS of the printer or something. But that’s waaayyyyy out of my skill set and I don’t see how it’s necessary if every tutorial on KZfaq doesn’t mention it. I don’t wanna do any more damage than I already have

@spray_cheese 7 ай бұрын

@@techs.passion ignore my last comment: Things have changed. Still not working. But I found the official support for it. Installed that firmware. And I’m following tutorials exactly. - autohome. - set the z offset - manually level the bed - autohome again. In which case it SHOULD do the 9 points. But instead it just undoes what I did. There’s no videos or forums talking about any issues with these. And if there are there is no replies. Do I just have a defective unit? That’s the worst part about all of this nonsense. You could troubleshoot til the day you die and it could just be a faulty component that they just decided to send me anyways.

@techs.passion 7 ай бұрын

It could be a defective unit but did you make the g code change in the slicer? There is a pinned comment on this video talks about it. This might be the problem. Sorry to hear, keep me posted and I will try to help as much as I can

@spray_cheese 7 ай бұрын

@@techs.passion I got some assistance on Reddit from someone who had the same issue. Apparently I needed the GD version of the firmware. And that solved my issue! I appreciate your help anyway. You helped me keep going:) thank you!

@TheRealWorld198 Жыл бұрын

why don't we put the g29 code underneath the g28?

@techs.passion Жыл бұрын

You are correct, that's the correct way of doing it. It's still working fine for me but the right way is under. Thank you for watching and the correction, I appreciate it so much

@TheRealWorld198 Жыл бұрын

@@techs.passion no problem! I do have another problem though, my ender three always shows no tf card. Can you tell me how to fix it? It’s brand new, there are no files other than prints, and I always eject it properly from my laptop. ( it is also formatted to the correct way) it was also working perfectly fine for my first three attempts, but then I just got the warning. And if it doesn’t show the warning, it doesn’t show a print. Thank you

@techs.passion Жыл бұрын

@mdproForPC 11 ай бұрын

i have ender 3 pro which update should i downloiad?

@techs.passion 11 ай бұрын

Hi, what is your motherboard version, I will look it up for you and see if I can help find the correct update for you :)

@mdproForPC 11 ай бұрын

@@techs.passion i have just check it's 4.2.2 ender 3 pro

@techs.passion 11 ай бұрын

Thanks for the details. This is what I found for you, please verify everything but I hope I got it correctly and I hope it is helpful. In case this is not clear, I will make a video later today to show exactly how to do it, I will share that with you when it's ready. Here are the links: For CR touch, in this link here www.crealitycloud.com/software-firmware/other?source=1 Go under Ender Series Then choose the Pro and your Mainboard Version: V4.2.2 and choose the firmware. Read the description but it looks like there are languages different and some different release dates. For firmware and general user manual, this is your page www.creality.com/pages/download-ender-3-pro?spm=..page_1934481.products_display_1.1&spm_prev=..page_1934481.header_1.1 So unless you have something other than default, go with this Ender-3 Pro Marlin2.0.1 - V1.1.2 - ALT(32bit) I will make a more detailed video tonight hopefully it helps out a bit more. Good luck and thank you for watching

@mdproForPC 11 ай бұрын

@@techs.passion thanks bro i will buy the cr tomorrow so i want to check everything is working for me before i buy it

@techs.passion 11 ай бұрын

For sure, there was a link with a discount on my video, I hope it still works (not a sponsor or anything) If you find a better deal you take it of course. I do not care where you buy it from, I only want to help you get a good deal as a thank you for watching. Good luck with the upgrade

@HFR_SpartanFred 6 ай бұрын

why change start gcode?

@techs.passion 6 ай бұрын

It lets the printer level the bed before starting using the CR touch

@HFR_SpartanFred 6 ай бұрын

@@techs.passion it wont work if we dont change it?

@techs.passion 6 ай бұрын

It will still work just fine from my own experience but it's recommended to update it. There is a pinned comment explaining it

@3dprinterguy397 13 күн бұрын

So when I put in my sd card it's formated and works but it's not showing up on the screen if you do find it you can't choose the thing and i still need some help with z offset, should I get a new one that already has one or what should I do I can post a video on my channel to show you

@techs.passion 13 күн бұрын

Did you upgrade the firmware already? You need the new firmware to be on the SD card then of course you need to add your prints files as well before it can see anything Yes, happy to look at a video if it helps, also you can post it to my discord, it's free

@3dprinterguy397 13 күн бұрын

@techs.passion I don't have discord but I will post I video about it and can you help me about the z offset I'm new to this and I don't get it I already put in the firmware and have a gcode to put in there the torture toast test

@3dprinterguy397 13 күн бұрын

I just uploaded it on my channel

@3dprinterguy397 13 күн бұрын

Is there a way to factory reset or what, I can also show you my slicer software too if you need it and sometimes the file will load up put you can't click it you can only choose main and nothing else, got this for my birthday and thinking about selling it and get a new one of you want me to i can post a long form video of me inserting the sd card and all that stuff in my laptop if I need ti

@3dprinterguy397 13 күн бұрын

And sometimes it doesn't even read the sd card

@yeet_65 6 ай бұрын

I am downloading the right thing for my version 4.2.2 board but when I put the microSD card in it doesn’t work and just loads like normal does anybody know why the firmware won’t update on my printer

@techs.passion 6 ай бұрын

Hi, you came to the right place, this video should help kzfaq.info/get/bejne/i9Njaaid3rrMg2g.html If not, please let me know and happy to offer further help if needed

@yeet_65 6 ай бұрын

I got onto the download page that you suggested, and got the file for my board but when I put it in it didn’t flash the file onto my printer and again loaded up as normal so I’m not sure what I should do next.😅

@yeet_65 6 ай бұрын

It was the file for the CRtouch

@techs.passion 6 ай бұрын

So you want to make sure that file is on the top level on the SD card and ensure your SD is formatted correct

@yeet_65 6 ай бұрын

I have formatted my SD card to fat32 and put the file into the sd card and it still didn’t work the only thing I’m not to sure about is how to put the file on the top level not sure what you mean 😢 but thank you so much for the help

@vegaspedalbloxx 3 ай бұрын

do I unplug z axis ??

@vegaspedalbloxx 3 ай бұрын

other videos showed it and you showed the board once with it unplugged but middle of video I'm confused then plugged back in after in other clips....

@techs.passion 3 ай бұрын

Yes, unplug the Z

@techs.passion 3 ай бұрын

Sorry for the confusion, unplug the Z that's correct

@angelalovett6371 11 ай бұрын

I did all these steps and still it’s to high off bed

@techs.passion 11 ай бұрын

That would be the Z offset is the reason. Also I noticed that the software is not the best depeding on which version you are using but I would set the Z offset and ensure it is holding the value. Let me know if you need further help with that. Good luck

@sirvenomslayer 5 ай бұрын

I don't have that port

@techs.passion 5 ай бұрын

Which motherboard version you have? Is it ender 3, you should have it unless you have the very old version

@sirvenomslayer 5 ай бұрын

@@techs.passion I must have a very old version bc there is no port for it

@sirvenomslayer 5 ай бұрын

It says creality ender v1.1.13

@techs.passion 5 ай бұрын

That is the very old one, that said I'm not sure if it has it or not, it sounds like you don't have it but I'm not 100% sure

@sirvenomslayer 5 ай бұрын

@@techs.passion I don't have the port anywhere so I'm toadt

@landon_gaming210 2 ай бұрын

Can you help I got it to work but now it all in Chinese😂

@techs.passion 2 ай бұрын

Oops, you might have selected the wrong version of the firmware

@landon_gaming210 2 ай бұрын

@@techs.passion I got it now it was on the right thing I just need to change the language

@techs.passion 2 ай бұрын

Glad you got it working

@FussySucker 10 ай бұрын

Hi! I LOVED THE VIDEO also my firmware is 4.2.2 and my board color is black. I believe it will work with 4.2.2. But you we're saying "I believe that 4.2.2 will work" Can you double check please i haven't bought my CR touch yet and i wanna make sure it will work before buying it

@techs.passion 10 ай бұрын

Hi, For sure, let me double check that for you. I will update you here soon. Thank you for watching :)

@techs.passion 10 ай бұрын

I just confirmed it, it is supported for 4.2.2 for Ender 3. This is the link to the firmware on their site www.crealitycloud.com/software-firmware/other?source=1 Thank you for watching my video and glad you found it helpful. Let me know if there is anything else I can help with.

@FussySucker 10 ай бұрын

@@techs.passion yay

@FussySucker 10 ай бұрын

also 4.2.2 mine is 32-bit right?@@techs.passion

@techs.passion 10 ай бұрын

Correct, the 4.2.2 is only 32-bit so you should only have that one option. Don't hesitate to ask if you have any other questions :)

@Blazing_Phoenix_YouTube 11 ай бұрын

Btw if you forgot to check just scroll down to about printer and it will tell you there. @techspassiondiy please pin

@techs.passion 11 ай бұрын

Hi, not sure if I fully understand you, Scroll down in the about section to tell you about what? Thank you for your comment, this video already have a pinned comment and I can only pin one at a time. I would love to pin your comment if I didn't have one already, maybe on another video if you can leave a helpful comment, I would be happy to do so :) Thank you for watching