I'm absorbing all this information wanting to buy a 3D printer. Thanks!!!

ive been having y axis skips on my cr-6 se since i conevrted to klipper and do high accel high speed prints to the point i swapped steppers,belt and wheels and still happens someitme sruingin a print an dmaking horrible vibrating sound so im at a point where i either swap themaing bpoard to see if thats the issue or maybe just quit spending on it and buy a new printer, i have a sonci pad already will this be a good steup or shold i lok to something higher in the range?

Great video!

Bottom is off. 240 seems hot - Was it PTEG?

When you paused a print can you charge the filament color and then resume the print?

I have a quick question. There is no CR10-SE profile on Cura. How can I manage that? Creality Print is not quite enough for me. Would you recommend any other slicer for this model? But first, if you know anything about managing the Cura and help me about it, that would be great🙏🏽

I’d like to replace an Ender 3 S1 pro with the CR 10. I’m very new to 3D printing. I like the CR 10 (great video BTW) for the speed. I don’t do a lot of printing because It’s still new and amazing to me. Is there anything to watch for if I get this printer? Can I start printing from the box after setup without downloading any firmware?

Any chance you can point me wto where I can get the STL for that creality scraper?

Hi!!! Did you say the nozzle is the same as K1??? I’d like to know that because I want to buy a 0.2 nozzle to my CR10SE. Thank you.

still don't understand why the filament sensor is an after thought on these machines. Seems like they could easily add the filament sensor to the hot end. Great video, Guy!

I got one of these the other day, and I’m still trying to get it setup. It seems that no slicer softwares actually have the printer setup available, and nobody has vids on it either.

I got one for $250, to replace my original e3. I do wish it retained more of the cr10 build volume and wonder who decided to call this a CR10 vs a 5 or CR6 SE v2 etc. I’m looking forward to playing around with it while my T1 is being built. The S1 and T1 are delayed again and surprised no KZfaq videos on it yet. Thanks for the review.

Were you able to get rid of the Z Banding? I bought one and can't seem to get rid of it

First one should note; This is not a CR (in name only) nor is it an E3S1Pro. All linear rails and the xy bed rail looks like it was fabricated out of a 57Buick bumper (beefy). The stepper motors are huge, 48's. The tool head is a their Sprit direct drive, but with a Volcano hot end with hardened steel tip and can go to 310c. The heated bed can goto 110c. The injection molded base/enclosure is a direct copy of the E3S1Pro. The internal side where the rails bolt too are all metal framing. For brains it has the Neptune pad so it is a "Klipper" not a Marlin. It can also use both the AI camera as well as the Lidar module from Creality. It can also use the Falcon 10watt Laser kit which I also have. The fit and finish is top shelf as in Lincoln Continental compared to a Ford Focus (they are both technically cars). Did I mention that it is also a hotrod. 19min Benchy in a near perfect print. I don't know maybe I should start doing uTube unbox, review, here is the spec sheet stuff. If you need an enclosure so you can print nylon carbon fiber which this thing can do Clearviewplastic.com makes them for this model. The closest model to this one is the Ender3 KE, but without the beefy versions of rails, hotend and motors. Yes I pre-rooted mine day one and have full access to all things Klipper.

How to calibrate X,Y,Z axis? How to change flow during printing? How to send gcode commands? I own this printr for a month, and can't find those informations.

I continue to pop error codes directly out of the box. I was able to print the test boat just fine. After two small test prints off of thingiverse, I can't print anything else. I get "nozzle heating not as expected" and "Key:3000 unknown exception" I've had this model for two weeks. It will pass the self tests, but continues to pop the Key:3000 nozzle heating not as expected" This is my first printer and I'm at a loss. The creality website has 4 error codes, and nothing related to this issue. Any thoughts would be greatly appreciated!

Which slicer do you use for this printer?

Got this about 4 days ago and it would seem that Creality's bed mesh does a poor job of adjusting. My bed has a tilt From the left to the right and there will always be small elephants foot on the higher side of the print

_If_ I were to buy a Creality, I'd opt for the K1 in place of this one personally. Being limited to PLA, PETG, and perhaps TPU doesn't make sense to me at it's current price. While fast, the print quality is still rough to me compared to a K1 anyway. Thanks for the video Guy, always enjoy them!

STL for the trash can?

I got mine at $330

I think we should wait until the ender 3 v3 KE appears...

Taking mine back this is a polished turd. The fan is so loud I couldnt keep it in my room had to put in another room and can still here it. The lack of tuning settings is a huge negative I can not adjust speed while printing or lower the z. Ive tried printing several items at 100 speed that have turned out horrible and this is for a machine that boasts 600. No support with cura! Think twice before buying this printer

Cool because there are no wheels... a reviewer from God