Cura Questions! Easier support Removal!

Рет қаралды 53,304

Күн бұрын

Are you struggling to remove support form your cura #3dprint? let me show you the settings to fix it, on cura question! if you have a #3dprinter question, leave it in the comments! today we are looking at support interface, and how to make the structures easier to remove!
Like and Subscribe!
Send me a gwei! (ether address, all donations accepted!)
0x95F4EaB8A738F4F27e7c04aEe1E10C8E666C2D0c
send me a satoshi! (bitcoin address, all donations accepted!)
31zvj8ybxVVTLw6nPvAHYqu3qDVhC1sRqk
Find 3dprinters and other cool Tech at:
www.amazon.com/shop/technivor...
SUPPORT TECHNIVOROUS 3D Printing:
TeeSpring Technivorous Merch!
teespring.com/stores/technivo...
become a channel member for youtube perks!
/ @technivorous
Paypal: Vanethrane@gmail.com
Check out my Patreon page: / technivorous
or you can buy me a coffee: www.buymeacoffee.com/technivo...
Current Channel Goal: 50,000 Subs!
Want to send me something?
Technivorous
902 n Hughes
Blunt Sd 57522

Пікірлер: 36

@Mambafpv Жыл бұрын

thanks bro, trying right now, my support are as strong as the print subject at the moment, so frustrating thanks for the tips on the interface and the preview checks are awesome, i never knew about that.

@arielalejandro6900 Жыл бұрын

I almost chop my finger off with a knife trying to remove the support knew there was something I should had tweak in order to make it easier to remove..., thanks...

@JustInvertedFpv 2 жыл бұрын

I've typically increased support z distance and had decent results with ease of removing supports but I'm definitely checking this out now. Thanks!

@4FramesPerSecond Жыл бұрын

What do you normally set it to? I have my at the default of 0.1 and it's sticking bad to the model. Would .3 be okay?

@grillosius Жыл бұрын

thanks dude, your settings helped a lot! the supports came of like a charm!

@smileyllc Жыл бұрын

Nice video! Really helped me a lot with removing supports on smaller prints.

@jaysvlog9803 Жыл бұрын

Now this is a video I’ve been looking for

@madnes8313 2 жыл бұрын

super helpful

@Frightline777 Жыл бұрын

You ROCK!

@ronm6585 2 жыл бұрын

Thanks.

@3DJapan Жыл бұрын

I'm having the opposite problem. My head has sharp, pointy teeth and the supports aren't reaching some of them. Maybe I need more interface instead of less.

@johnm.gerard1718 Жыл бұрын

Thank You I am going to try on my next print. My automatic supports in cura 5.0 just weld themselves to the print. Absolutly no way to remove them. So I have been using manual supports which works ok but still not great. One print using cura 4.x and the supports removed very easily. Have be stuggleing with Cura 5.x. I was hoping that I could go back to using Auto supports. Much easier than the time it take to add supports Manually.

@Jojo-om2hz Жыл бұрын

Hi there.i may have the latest cura version and wanted to ask do you have any solution to enabling support density as its greyed out.i tried to changed certain settings but it's still greyed out.Thank you for the vids

@mamadoubapassioninformatique 2 жыл бұрын

Thanks a lot. In Cura, which infill pattern do you think makes the body stronger?

@LegendKrazy 2 жыл бұрын

Lmao love how he hearts the comment but doesn’t respond 😂😂

@mamadoubapassioninformatique 2 жыл бұрын

@@LegendKrazy Good question 😂

@Outofbox11 2 жыл бұрын

have you had an issue where while printing with lot of support and hear crackling noise from nozzle hitting support when traveling? some strange reason i've been having that issue.

@Technivorous 2 жыл бұрын

Ther is a settibg that allows you to avoid the supports. Its paths around parts that are already printed, so it adds print time. But its worth it.

@user-ds2uj1kq9u 6 ай бұрын

I started my first print with interface turned on. Running line support at 20%. Will it still help out? And is that a good line density?

@carlitos7792 Жыл бұрын

How do I remove the yellow lines? It won't let me print hollow parts

@papasplace2 2 жыл бұрын

The major problem with removing support I am having is when the support is in a hole for a bolt...any suggestions?

@Technivorous 2 жыл бұрын

Get a good grip with some needle nose and instead of pulling, turn it. It should seperater at the interface which is the weakest. Otherwise, get a slightly smaller drill bit than the hole, and tap it out

@1937Brett Жыл бұрын

I need so much help for my PETG supports

@fxgilbert2374 Жыл бұрын

hi, every time i put support on a big flat surface it make me big ruff layer line, i tried to do floor and top draft support if it might help but finally no

@Technivorous Жыл бұрын

Do a raft for adhesion instead of brim or skirt. That will give it something to print on. Also, check the support roof, and support interface... Turn the roof on, and increase the interface distance by .04 until you achieve the desired results!

@Explore531 Жыл бұрын

the new update already fix that issue everything that shows on your video it set for default on Cura 5.3.1

@monkeydad47 Жыл бұрын

ah, interface density was at 100. No wonder the damn things wouldn't come off!

@CLos943 Жыл бұрын

Hey bro what's up not to bother you but I got a 3D printer and trying to rip off these supports but cutting my hands up like I'm watching your video trying to figure things out it's complicated for me to understand maybe not for others but what I'm just trying to understand is doing all of the correct settings so everything could be just right

@Technivorous Жыл бұрын

Look at the support interface settings. I'll make ya a video if you'd like

@mickyas1000 Жыл бұрын

Absolutely terrible, just wasted an 11 hour print using your settings...the supports had a better hold than the actual print i wanted to keep. I suppose that's what i get for listening to people who think they know better.

@thenicksears Жыл бұрын

could not disagree with you more about treelike vs linear supports :/

@joshtherussian9261 2 жыл бұрын

Why not use a different filament for the support part? Like VXL, PVA or similar?

@Technivorous 2 жыл бұрын

If you have a dual extrude, dissovable support is optimal!

@joshtherussian9261 2 жыл бұрын

@@Technivorous Not even - You can manually switch if really needed, but it isn't that easy tbh.

@float32 Жыл бұрын

@@joshtherussian9261 I don’t think I’ve ever printed anything with less than a few hundred layers. I think for a rational person, multi filament without dual extruder is not worth it. Just spend the money on a cheap dual head printer. Don’t be a machine. Your time is worth more than that.