Custom DIY Mini Bike - Part 2: Rolling Chassis

Рет қаралды 27,469

5 жыл бұрын

By the end of this video, I have axel, wheel, and engine mounts completed with front forks on the mini bike. Aside from getting controls and handlebars, a seat, and bolting everything up, the mini bike is nearing completion. While I did improvise or change many of the ordinal measurements, here are the files I used: drive.google.com/drive/folder...

Пікірлер: 31

@craigmonteforte1478 4 жыл бұрын

i really like the square stock frame it sort of changes the appearance to give it that full custom look and not another store bought frame looking foward to finding out how it rides the rolling chassis is sharp good choice on the bars too

@gkgt5226 4 жыл бұрын

Craig Monteforte Thanks you!

@terrinewman7390 3 жыл бұрын

I had thought of using square stoct also, no tube bender! but thw square tube looks greatand I like it!!

@gkgt5226 3 жыл бұрын

Thank you!

@charliemclaughlin1042 3 жыл бұрын

Great job man liked the video 👍👍👍👍👍

@gkgt5226 3 жыл бұрын

Thanks!

@yassinplays5299 4 жыл бұрын

Awesome video !! Keep it up

@gkgt5226 4 жыл бұрын

Thank you!

@arlenen7820 4 жыл бұрын

Great vid keep it up man👍👍

@gkgt5226 4 жыл бұрын

Arlene N Thank you!

@gustavocalderon3592 2 жыл бұрын

I really like your build, using square tubing and straight lines you don't need a bender. could you share measurement plans thanks

@lomsomesGarage 4 жыл бұрын

Great video

@gkgt5226 4 жыл бұрын

Lomsome's Garage Thanks!

@asenkbogar5180 4 жыл бұрын

Great vidio ,keep spirit brooo..im from Indonesian

@gkgt5226 4 жыл бұрын

Ferdianto Bogar Thanks, very cool to know!

@richardhatt6541 4 жыл бұрын

You have quite the wobble in the rear wheel.

@gkgt5226 4 жыл бұрын

Richard Hatt I have since rebuild the rear wheel and believe it’s fixed, but thanks for the pointer.

@cadenburt3292 Жыл бұрын

What size pipe on the front forks did use if you don’t mind me asking

@gedu6881 2 жыл бұрын

What are the dimensians of the minibike frame

@richardhatt6541 4 жыл бұрын

How heavy is the frame? I was planning on doing the same with square stock but it looks really heavy.

@gkgt5226 4 жыл бұрын

Richard Hatt I have not weighed it, but I don’t think it’s too bad for square stock, still kinda heavy though.

@Annatar0 3 жыл бұрын

The frame is well enough for two grown people to sit on it. Look at the vintage mini bike frames as they are much smaller. I'm building a similar mini bike right now with the same profiles as in this video. But I made the backend of the frame just 90degrees instead of a slight angle to fit a 15l generator tank haha because that's what I had laying around.

@gkgt5226 3 жыл бұрын

@@Annatar0 That's very cool; I do agree it is quite large for a mini bike.

@Annatar0 3 жыл бұрын

@@gkgt5226 It all depends on how you'd want it to look, personally I like the look of a square frame rather than the round typical bike frame.

@itsdarooster8160 2 жыл бұрын

Sucks I just found the channel I think your a hell of a person

@mikesmith4764 7 ай бұрын

Where do u get ur metal?

@abduliippa2931 3 жыл бұрын

where did u get ur wheels from?

@gkgt5226 3 жыл бұрын

The front one is from harbor freight, and the rear is from an old min bike.

@abduliippa2931 3 жыл бұрын

@@gkgt5226 thank u for the reply other thing im wondering is how long is ur rear axle? cuz I want to make 1 but dont really know how long the axle needs to be.

@gkgt5226 3 жыл бұрын

@@abduliippa2931 I'll have to go measure it. I'll drop a reply when I do.

@gkgt5226 3 жыл бұрын

@@abduliippa2931 Mine is about 10.5 inches, close to the width of the frame.