No video
Customer drove in with less than 1 quart of oil. Front and rear wheel bearing replacement.
Рет қаралды 824
Ай бұрынCheck out The Offroading Mechanic amazon affiliate store to help out the channel.
amzn.to/3SiOjXd
Inner tie rod replacement.
• 2005 Pilot almost @400...
Follow me on TikTok
www.tiktok.com/@theoffroading...
------------------------------------------------------------------------------------------------------------------------------------
YOU CAN ALSO ENJOY WATCHING THESE :
Thieves are getting a little bit smarter, just a little.
• Thieves are getting a ...
Honda Pilot, Odyssey, Ridgeline & Passport 9 speed automatic transmission fluid type 3.1 replacement
• Honda Pilot, Odyssey, ...
2016 Honda fit, no start, no charge, no communication (DIAGNOSIS)
• 2016 Honda fit, no sta...
First break in oil change on the 2023 TRD Pro 4runner.
• First break in oil cha...
What I think about the 2023 4runner so far and what kind of problems I have had
• What I think about the...
2008 Honda civic spark plug tube seal. (not really tube seals but crush washers)
• 2008 Honda civic spark...
Customer states my blower motor doesn't work on any speed. Here's a trick I like to use In a pinch (cool trick if you don't have a test light)
• Customer states my blo...
Disclaimer:
Due to factors beyond the control of The Offroading Mechanic, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. The Offroading Mechanic assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. The Offroading Mechanic recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of The Offroading Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.
---------------------------------------------------------------------------------------------------------------------------------------
#carrepair #Theoffroadingmechanic #automotive #carmaintenance #toyota #honda #generalrepair
@jptrainor Ай бұрын
I check the oil every 20% on the oil life and top up as necessary. My two Honda's both burn some oil at 245k km and 400k km. The engines both run perfectly, other than burning a bit of oil. The 400k km engine is a 2006 Civic. It burns about 2 litres per oil change interval (8-10k km).
@stewartthompson7556 Ай бұрын
Perfect timing … just when I needed an Offroading fix
@bearing_aficionado Ай бұрын
As the official bearing aficionado of this channel, I can confirm that wheel bearing is bad. Sounds like its on life support at this point!😂
@theoffroadingmechanic Ай бұрын
I didn't even need to go 60kms/hr until I started hearing it.
@bearing_aficionado Ай бұрын
@theoffroadingmechanic what was the part number for that hub bearing? I know it was an SKF bearing. It looks like our 51-01 hub bearing we make for Honda.
@theoffroadingmechanic Ай бұрын
I didn't check the part number for the rear so I'm not to sure. I'll have to find the box on Wednesday. The front bearing is fw97
@bearing_aficionado Ай бұрын
@@theoffroadingmechanic if that bearing has the same dimensions as ours, we call ours 51-01. Year and model of vehicle? I'll see if I can cross reference them.
@theoffroadingmechanic Ай бұрын
It's a 2007 Odyssey
@HiFiInsider Ай бұрын
can you please make a video on how to flush the PS fluid for DIY without air suction tools?
@jptrainor Ай бұрын
Pull the return line and extend it into a waste oil pan. Run the car, turn the wheel stop to stop once. Shut off. Don't run unnecessarily long. The system will have emptied itself into your waste oil pan. Finally fill it up, run it, turn the wheel stop to stop, and top up as necessary. Use OEM power steering fluid.
@theoffroadingmechanic Ай бұрын
You can use a hand pump fluid extractor. I always suck out the old stuff and fill it back up first before starting it up and turning the wheel lock to lock so it doesn't aerate the fluid and make the pump start whining. Then shut it off and suck it out and fill it back up and repeat.
@michaelkane732 Ай бұрын
you might try that trick with the 17 mm wrench where you live but in the rust belt here you will snap it off every time, get the torches out please
@jimharrison3552 Ай бұрын
Klondike Bars, original were called Eskimo Pies, but in the time we live in not to offend anyone the name was change to Klondike Bars.
@kevinbarry71 Ай бұрын
You have been watching too much Fox News; Klondike bar came out in 1922. And was not a new name for anything
@jimharrison3552 Ай бұрын
@@kevinbarry71 As usually CNN fake news, Eskimo Pies was patented in Jan. 24, 1922 .by Christian Kent Nelson,
@HiFiInsider Ай бұрын
first! I like diaga videos. Is that oil filler gauge available for DIY people?
@theoffroadingmechanic Ай бұрын
That's just for our bulk oil. I typically will be filling oil with a 5L jug at home.
@SPMech1 Ай бұрын
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@dpose6525 Ай бұрын
omg, one quart of oil. How did that thing not grenade
@jptrainor Ай бұрын
A testament to Honda's engineering. They build them assuming they'll be abused. Hence if you don't abuse them they outlive the rest of the car.
@theoffroadingmechanic Ай бұрын
The old j series motor V6 will keep on running as long as you keep oil in it. When it starts burning oil slap some new rings in it.
@kevinbarry71 Ай бұрын
It's not a Chrysler. Or a Nissan. Nevertheless, I have to think the life of that engine is limited now
What the Meowk!
Рет қаралды 8 МЛН
The Daninator
Рет қаралды 1,3 МЛН
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 1,5 МЛН
Dave's Auto Center
Рет қаралды 416 М.
The Offroading Mechanic
Рет қаралды 2,7 М.