Cutting Metal Corners

No video

Cutting Metal Corners

Рет қаралды 768,887

MR Post Frame | Marshall Remodel

Күн бұрын

Пікірлер: 180

@51-FS 2 жыл бұрын

Some people don't have pride in their work anymore. Your not one of them

@channel_alan Жыл бұрын

I dunno. Looks to be like he's cutting corners. 🤔

@51-FS Жыл бұрын

Lol

@andrewrobinson2869 2 жыл бұрын

I use to be a ceramic tiler. Its so nice to see someone who takes pride in his work. God bless you sir.

@moriscoley5328 2 жыл бұрын

You are absolutely correct 💯, some people don't give a flying flip and it shows that, forever!! I have seen good jobs and I've seen a ⚰️ rotten.

@jefffowlerr Жыл бұрын

You could also leave a section on the back part so you can bend it over to help prevent water getting into your corner

@seepatterson5878 9 ай бұрын

How? Can you post a video @jeffowlerr

@bill7618 2 жыл бұрын

Good to someone who is good at their trade and gives a damn about the details . Great job !

@GirlGangsta33 2 жыл бұрын

I swear you’ve done that before!!! Lol. Great vid. Great workmanship!!!

@Rezorcful Жыл бұрын

You probably watched rrbuildings do this video years ago

@rabid_panda1117 2 жыл бұрын

I don’t like cutting corners. But in this case, I’ll let it slide. 😆🤣😂

@howardjohnson6189 Жыл бұрын

😂😂👍❤️

@luisq825 2 жыл бұрын

Excelente cut, thank for the lesson

@sterlingarcher1962 Жыл бұрын

I just learned something about snips. SO HAPPY :-D Thanks!

@johnbagewll2321 Жыл бұрын

Of all the things I’ve mastered over the years, sheer tooling is not one of them. Bravo.

@erikg1494 2 жыл бұрын

As a sider I appreciate the hell out of the hidden seam

@ahill7099 2 жыл бұрын

Could leave the back and wrap it around vertical corner. But nice work

@MyPimpalicious Жыл бұрын

as a metal roofer I agree there should be a tab on the back also.

@kathleensabino374 11 ай бұрын

Thank you! So helpful 😁

@MrPostFrame 11 ай бұрын

Glad it was helpful!

@keithmcadam185 2 жыл бұрын

Well done I'm sure many people will see this video and be thankful Ford.

@Fishman138 Жыл бұрын

So simple and beautifully done.

@kbonestom5392 2 жыл бұрын

You need a tag on the upstand, still got a little bit to learn but almost there mate

@4OHz 2 жыл бұрын

One of the best little bits of advice I’ve seen. Well explained and we’ll executed. Practice does not make perfect, practice makes better. Thanks.

@MrPostFrame 2 жыл бұрын

Thank you for your comment!

@4OHz 2 жыл бұрын

@@MrPostFrame it’s a great little training video - if you’ve got the patience for this you could be a real asset to your fellow man. It’s so “see one, do one, show one.” I’ve actually saved the link so I can show my gutter and standing seam guys. They may know it but I don’t think they’ve seen it so we’ll explained - especially the college guys on his summer crews.

@jamesortolano3983 2 жыл бұрын

Red's nd green's ,make it all possible. Nice information.

@roberthartzell7104 Жыл бұрын

Very impressive! Someone who takes pride in their work 🙏🙏

@MrPostFrame Жыл бұрын

Thanks!

@gerrykeane4532 2 жыл бұрын

Nice to see a Craftsman at work we need to teach our young people in the trades and build our way back to Greatness and make made in America mean the Best again

@moriscoley5328 2 жыл бұрын

MAGA 🇺🇲 👍💯

@jfssparky Жыл бұрын

Professional, excellent work

@brianparsons6916 Жыл бұрын

Wow that's awesome very informative thsnks great job

@Ibaneddie76 Жыл бұрын

Those are the things that matter in construction, fine tuning the finishing work!

@paulamberger319 Жыл бұрын

All you haters,F -OFF🤬

@chinhuanglee8576 9 ай бұрын

Thank you sir for sharing your knowledge God bless you ❤

@shaffer4220 2 жыл бұрын

That what I’d like to see. Excellent

@jeffmaxwell4579 Жыл бұрын

Sweet! Keep Being Safe Out There!

@cousin_JACK Жыл бұрын

Thanks for the tip

@Pizza_Master Жыл бұрын

thanks that was a great technique

@roczilla6834 Жыл бұрын

Sweet cut! Thanks Brother

@JohnnyRingo1863 Жыл бұрын

Excellent technique

@jzeerod Жыл бұрын

oh wow. nice. i have to use flashing because some houses were built before rezoning, the front street and back alleys are higher than the top of the foundation. wood rots through the stucco.

@Graysonn95 7 ай бұрын

Should have a tab as well that folds over, to one comment I saw asking how it's done: Just cut one of the outer marks on nailing flangs + middle line, do your first angle cut and then cut the inside bend where your flap is

@user-oc6qs1po3j Жыл бұрын

If you leave the flap on top edge you bend that around corner also siding covers it an helps water proof it

@jerryklooster438 Жыл бұрын

Very nice.

@MrPostFrame Жыл бұрын

Thanks!

@theoriginalmonstermaker Жыл бұрын

Very helpful

@warmonger9124 2 жыл бұрын

Very good instructions. 👍

@nikl1604 2 жыл бұрын

Should have left a tab can't caulk it very well without one !

@chriswiggins4842 Жыл бұрын

Very informative

@Josh-ww5kz Жыл бұрын

Exactly how i would do it. Just a bit tricker when you have another bump out at the bottom instead of going straight veritcal. Like more of a dripedge. Thats when you have to two piece it otherwise youre going to have to cut the dripedge hem and it doesnt look as neat

@telmoguerrero Жыл бұрын

Good job men !!!!!!

@cdbwc Жыл бұрын

I did rain gutters and visible seams are important!!! Nice to see I wasn't the only one who cared.

@MrPostFrame Жыл бұрын

Thanks for watching!

@bryblanch Жыл бұрын

Freakin Sweet!

@JillofAllTrades2 2 жыл бұрын

NICE!!

@jasoncarle9058 Жыл бұрын

Top notch!!! 👍

@MrPostFrame Жыл бұрын

Thanks

@RRED2 2 жыл бұрын

Clever idea. Thank you 👌

@7628739 2 жыл бұрын

On another level

@rocknral Жыл бұрын

That last cut ...would be better to leave a tab to bend on the vertical at 90 around the corner. But very neat all the same.

@shimmy285 Жыл бұрын

Thanks!

@MrPostFrame Жыл бұрын

Thanks for watching!

@petergillespie564 Жыл бұрын

Nice cut mate

@peterparker9286 2 жыл бұрын

Green= rights cut a right circle clockwise Reds= left cut a left circle counter clockwise. Always keep your snips 90° to your work. Plumb no lean...

@sarb6p55 Жыл бұрын

Your right guy’s that pay attention what they do are awesome 👍

@brianb5779 Жыл бұрын

Awsome Tip

@mos66247 Жыл бұрын

I do only standing seams. In wetter climates with wind, wouldn't take long for corner to rot.

@carlossacancela7124 4 ай бұрын

The best teaching wau

@dale2257 2 жыл бұрын

Well done

@sarahallison48 2 жыл бұрын

That was satisfying

@stark1987 Жыл бұрын

its hard to complrehend because im not a smart man, but that theres so much down to even cutting a corner, i could never remember all that needed for good construction

@CarlosSanchez-bg4wf Жыл бұрын

I love it bruh

@davidwhetherholt2370 Жыл бұрын

You make it look easy,Kyle from R&R builders does a lot like that.

@MrPostFrame Жыл бұрын

Thanks for the comment!

@angelacen6518 2 жыл бұрын

Thank my brother for this tip

@cloudlounger6903 Жыл бұрын

👏👊👏. Metalsmiths. 👏👊👏

@gentilejoshsaved1646 2 жыл бұрын

Perfect

@Can_non69 2 жыл бұрын

Quality work.

@awake4765 Жыл бұрын

Nice corner detail but why cut off the tab for the back flange, it would be better to keep the right flange for backing with sealant.

@4200timeB 2 жыл бұрын

Very nice

@MrPostFrame 2 жыл бұрын

Thanks!

@Titantitan001 Жыл бұрын

Im actually always impressed watching other trades. But idk I would still pay you guys to do it. DIY is a joke and I do Tile/bathrooms. Im not trying to do someone’s roof.

@lionelhernandez34 Жыл бұрын

Leave the true 45 side "seen most" about 1/8 long on the wall side. This will let you tin the excess over eliminating the need for any caulking

@lilsadboy69 2 жыл бұрын

This is art

@yoramnone1750 Жыл бұрын

amazing technic

@MrPostFrame Жыл бұрын

Thanks!

@buzzbustillos3016 2 жыл бұрын

Great video.

@raider3164 Жыл бұрын

Pro master

@danielrivera3535 2 жыл бұрын

😎 👍

@JJHemingway421 2 жыл бұрын

Hand benders baby!!!

@jayclark2077 2 жыл бұрын

See? It’s even easier than the last one!

@alejandroserrano6987 2 жыл бұрын

THAT'S SKILLS

@MrPostFrame 2 жыл бұрын

Thanks!

@chavajl8073 Жыл бұрын

No tab on nail flange that's a leak point rest looks good but teach people right water always finds a way our job as construction workers is to not only make things good to look at but functional at the same time that will fail where the the corner meets the wall water will find its way in there once caulking fails

@imdeplorable2241 Жыл бұрын

This is the only siding man in America who does this. Maybe, after seeing this video, the rest of them will start doing it this way.

@danielfinney4295 2 жыл бұрын

Cheap Jeff, I used to work at a sheet metal shop running a brake that bent that stuff

@SharkFishSF Жыл бұрын

Cutting corners wow....

@GT-43 2 жыл бұрын

Good lookin corner

@nigelguerrero6196 2 жыл бұрын

Please teach us about the different snjps

@peterparker9286 2 жыл бұрын

Rights Green cut a right circle Lefts Red cut a left circle Always keep the cutters plumb to what you are cutting.

@rotcaka 2 жыл бұрын

This is great! What about for the foundation piece? I have a Z that I'm working on, But it steps out an inch or so at the bottom. How would you go about that bend. The way I did the first corner was just the make two cuts and just bend tabs around and have both sides run long so there's a lap. I don't like it though and know there's probably a cleaner way.

@MrPostFrame 2 жыл бұрын

Is it rat guard trim? I have a full video on rat guard - Rat Guard Trim - Corner + End Finishes kzfaq.info/get/bejne/gN6WlbSqzbTSiqM.html

@rotcaka 2 жыл бұрын

Also, doing it the way I'm currently doing, I have to bend two pieces of metal as opposed to what you're showing which is just one bend to make a corner ...

@rotcaka 2 жыл бұрын

Dude you're the man! I'll check out this video for lunch and report back! Thanks for responding so quickly!! 🙏

@rotcaka 2 жыл бұрын

@@MrPostFrame It's not rat guard 😢 If you go to the part in your short video where you're cutting the 45 you can see a piece on the foundation below, I believe it's the same as what I'm doing only my piece of metal is much larger (from top down 6"x1.5"x8"). What I have is a step out where my stem walls are exposed and jut out about an inch.

@rotcaka 2 жыл бұрын

kzfaq.info/get/bejne/hMV9iKaeztS7gmQ.html @23sec. In this video is where I got the plan for how I'm doing mine currently. Although he is only showing the example using an "L"

@markaraujo06 2 жыл бұрын

I like tip ideas

@MrPostFrame 2 жыл бұрын

Thanks for watching!

@Crustyswede1 2 жыл бұрын

Very good thanks but like so so many videos, not even a half of a second to see final product. Very very annoying, so much so that I usually just go to next video and FORGET this one. Just a tip because I’m sure there are more people like me as well. 👍🏻

@MrPostFrame 2 жыл бұрын

Thanks! Purpose of video was to teach so more focused on instruction. You can our full length videos for final product.

@ricksterk7014 Жыл бұрын

Lol obviously!

@pingpong9656 Жыл бұрын

That is incorrect - the corner metal pieces touching the wall should be overlapped around the corner too... close but it's a leaker.

@markjeune5728 Жыл бұрын

45° cuts to form a right angle.

@viktorvasilik5477 Жыл бұрын

Are those Midwest snips?

@waterbuffalosick4735 2 жыл бұрын

Why are buildings in the US just made from Plywood, sheet, foil and foam ?

@darryltaylor8995 Жыл бұрын

Well done 🧸

@MrPostFrame Жыл бұрын

Thanks!

@stoneybakermd1936 Жыл бұрын

sweet

@ozoneswiftak Жыл бұрын

Wow.

@MrPostFrame Жыл бұрын

Thanks for watching!

@robertjohnston6387 Жыл бұрын

Ok mr rr buildings

@CarlAquaForce 2 жыл бұрын

If you've ever cut this shit , then you know how it's not as easy as it looks. 🤣

@DivineGains 6 ай бұрын

Is that even water proof?

@Taki7o7 Жыл бұрын

Ouch, just ouch

@cliffordbirchell2029 2 жыл бұрын

When I do that the dirt but daubers have a place to live

@kingpopper437 2 жыл бұрын

Does this work for roof flashing

@jzeerod Жыл бұрын

i usually just wing it. osb you really need to know where your studs are.

@tommytom5650 Жыл бұрын

A good metal worker can spot the major flaw with his corner.

@micahroberts3564 Жыл бұрын

A good driver can spot a major flaw with your driving