Cutting Zenith Compact worktop for Sink

Рет қаралды 35,742

Passion for Carpentry

3 жыл бұрын

Sink under worktop

Пікірлер: 53

@0kojack0 Жыл бұрын

Only thing I do differently is rather than cut the mdf jig with a skill saw, I screw straight edges around the edge of my pencil marks and then use those as a guide and use the router to cut the jig with the router too. Takes a little longer but means my jig is 100% straight. Drilling the sink brackets tests a man’s minerals 😂👍🏻

@dilligaf2386 Жыл бұрын

And use a work bench. Why would you cut on top of the appliance or cabinet can I use the word juvenile

@TonyofCornwall 2 жыл бұрын

Fantastic video. And at a really nice pace for me. You have given me so much confidence that I can do this now. Thank you so much

@hisunbeam 2 жыл бұрын

Great video very well explained keep up the great work

@SteveDiamond19 3 жыл бұрын

Neat trick with the jig you made.

@MrRedfreds Жыл бұрын

I would make the jig full width of the worktop, with a 2x1 lath at the front as a stop and straight edge. Keeping it parallel, I've just done a 22mm Howden joinery worktop u shaped kitchen, putting in the jointing bolts and cut outs for sink and hob, takes longer, nice router work ,cutting 4 or 5mm at a time saves your router bit.👍

@almusti Жыл бұрын

Do you round the top edge of the hole for the sink? Thanks for the great video! 👍🏻

@maciejsawicki7774 2 жыл бұрын

Thank you

@masratta Жыл бұрын

Very hard and good job, that's why the kitchen fitters asks a lot off money ...🤣🤣🤣🤣

@Ali-hl1ri Жыл бұрын

Do you cover the Bradford/Leeds Area? I need this exact worktop fitting....

@aleksandrasjurka7398 Жыл бұрын

For me personally if you do sink hole 10mm smaller would look better as sink edge would be invisible no?

@joannayw5272 Жыл бұрын

brackets are redundant if proper adhesive / silicone is used

@altoncool8079 2 жыл бұрын

Great work 👏 thanks for sharing 👍 Can link in description the tools that you are useing, where to buy please. The jig for drainage channels& router bit. Thanks ageing

@PassionforCarpentry 2 жыл бұрын

www.screwfix.com/p/trend-625mm-draining-groove-jig/1821r

@PassionforCarpentry 2 жыл бұрын

www.screwfix.com/p/trend-t10ek-2000w-electric-router-240v/66257

@PassionforCarpentry 2 жыл бұрын

www.screwfix.com/p/trend-shank-double-flute-router-cutter-trade-pack-12-7-x-50mm-3-pack/37734

@benyoung4333 Жыл бұрын

Great video mate. You made this look very easy. Where are you based for fitting composite work tops?

@PassionforCarpentry Жыл бұрын

Hi. I am Leicestershire. Thank you .

@benyoung4333 Жыл бұрын

@@PassionforCarpentry how far do you travel? Would you travel to Frodsham?

@PassionforCarpentry Жыл бұрын

This is my email: ejup@passion4carpentry.co.uk

@emirdzafo1569 2 жыл бұрын

Do you use the same tool for compact boards as for wood, I mean milling cutters

@PassionforCarpentry 2 жыл бұрын

Yes

@Wood_and_Stuff 2 жыл бұрын

Great videos, very high level of carpentry and joinery. sizin numaranizi alabilir miyim?

@lukepcreaney 7 ай бұрын

With these worktops they just butted or can you router off 3mm or is 1mm on the female part like a normal square edge solid wood? Thanks

@PassionforCarpentry 7 ай бұрын

Hi, these worktops are squre. They just need to be bolted ( specific bolt) and use biscuits for flat surface .

@GiGiL33 4 ай бұрын

Hi i am looking for someone to fit these worktops, every joiner has backed out when hearing compact laminate. Do you work around the runcorn area?? Please let me know 🙏🏻 thanks, R

@PassionforCarpentry 4 ай бұрын

Hi, these worktops are great, but not many traders fit them as they are high-risk. I am based in Leicester, and I don't go out of Leicestershire. I hope you find someone soon. Thank you.

@lukaszkubicki150 6 ай бұрын

What kind of router bit did you use for cutting hole for the sink and draining

@PassionforCarpentry 6 ай бұрын

Hi, same one we use for worktop.

@mozzzadmoz Жыл бұрын

a little tip for you sir, whne you have got the sink in the perfect place, draw around it. then would you are working onfixing it, sealing it e.t.c its quicker to realign. Great video

@stevengales4605 2 жыл бұрын

Hi. What are you using to cut the tap hole? Everything I've tried burns out before I get a few mm in

@PassionforCarpentry 2 жыл бұрын

This should do www.screwfix.com/p/multi-material-plumbers-bi-metal-holesaw-set-9-pieces/3851V?tc=CB4&ds_kid=92700055262507123&ds_rl=1244066&gclid=Cj0KCQjwlOmLBhCHARIsAGiJg7knKtP_09nIaZCod_6nmvdu7veEyU9c0hBHp0D-2MIsMGN2FiCAtgIaAujkEALw_wcB&gclsrc=aw.ds

@kerrymiddleton1034 2 жыл бұрын

@@PassionforCarpentry ñnn

@PassionforCarpentry 2 жыл бұрын

@@kerrymiddleton1034?

@rachid8343 2 жыл бұрын

What router bit do you use to get the smoothest cut?

@PassionforCarpentry 2 жыл бұрын

I used Trend 1/2" shank double-flute 12.7mm. I have used 30mm guide bush, this made it 9mm away from hand made Jig guide.

@rachidboumnijel2419 2 жыл бұрын

Thanks so much. After cutting the undermount hold do you also need to smooth it? Is there another bit for that?

@PassionforCarpentry 2 жыл бұрын

Yes you have to do it with sand paper and there is an oil which comes with worktop set .

@noelsdesign 2 жыл бұрын

@@PassionforCarpentry is that standard trend TCT blades ?

@PassionforCarpentry 2 жыл бұрын

@@noelsdesign yes

@emirdzafo1569 2 жыл бұрын

How to attach a compact to cabinets? Thank you

@PassionforCarpentry 2 жыл бұрын

Hi, first you cut worktop to the size you need for fitting then put worktop on top the cabinet as is gone be in finale position. Mark the worktop underneath were the side of cabinet are then turn worktop upside down use the same screw we use for the sink with L bracket, make sure the end of bracket is strait with marking.

@emirdzafo1569 2 жыл бұрын

@@PassionforCarpentry Is it safe to process compact with 8mm bits on router, and what is minimum power router recommended to Use?

@PassionforCarpentry 2 жыл бұрын

@Emir Dzafo NO, the router is a very good tool but danger as well. Small size bit only for soft wood and other material.

@emirdzafo1569 2 жыл бұрын

@@PassionforCarpentry I have a Makita RP0 900, 900w, I make softer wood with it, I thought to try a compact but it is quite hard, so I asked, thanks for the answer, I appreciate it

@claireharrison6346 2 жыл бұрын

can you come to folkestone and do mine

@PassionforCarpentry 2 жыл бұрын

Sorry but I am over 4 hours drive away from there.

@joshpowell7803 10 ай бұрын

Hi I am in the middle of fitting mine i was always wondering why the bolts to fix sink are 20mm what is that plastic spacer you are using

@PassionforCarpentry 10 ай бұрын

Hi, if the screw is 20mm you should have the same plastic included in the kit for sink fixing. The plastic is flexible rather having to fix straight in the metal plate.

@PassionforCarpentry 10 ай бұрын

Another way of doing is to use adhesive that comes the same as silicone tube, but you have to support from beneath, solid wood 10 cm wide. On the front of the sink .