CV Boot Replacement Peugeot 207

CV Boot Replacement Peugeot 207 | Driveshaft Gaiter

Рет қаралды 17,620

3 жыл бұрын

CV Boot Replacement Peugeot 207 | Driveshaft Gaiter
In this video I am replacing an outer CV Boot (Driveshaft Gaiter) on an 2008 Peugeot 207
This is a reasonably common MOT Failure item on front wheel drive vehicles and the procedure is similar for make different makes and models
I hope you have found this useful !
Please hit the thumbs up and subscribe to my channel for future videos.
Best Wishes
Tim

Пікірлер: 33

@mediable6 10 ай бұрын

Yes, found it useful when doing it for the first time, thanks!

@ljpug7208 2 жыл бұрын

Thanks Tim saved me a trip to the garage and more learning under my belt!

@michaelbirchall2247 2 жыл бұрын

Thank you. This is my next job!

@Robbie_27 9 ай бұрын

A good tip use a zip tie on the c clip when pushing the cv joint back on makes it lot easier.

@peteisi113 Жыл бұрын

Its ok Tim, i misled the groove where the boot slots into, Job done, sorted :)) It was my first attempt,Thanks for the vid 👍🏻

@minortinkering 11 ай бұрын

Sorry Peter only just saw your comment, glad you got it sorted ! Best Wishes Tim

@gregbruns8442 3 жыл бұрын

Good video, Tim! I know someone will find this very useful when they have to do this job. I watch a lot of these types of videos and yours is right up at the top in terms of production quality. You certainly could go pro if you wanted to. I'm not sure you'd ever get rich at it, but you certainly have both the mechanical skills and video production skills to make top notch auto repair videos!

@minortinkering 3 жыл бұрын

Thanks Greg I thought I would do some of these type of videos as and when I have little jobs to sort out. This is my Son in law’s (to be) van and it failed the MOT Test on a few little items so I offered to help him out and repair it. Thanks for watching Best Wishes 😊👍

@rrr...512 2 жыл бұрын

Great job. Thanks for that. 👍

@willtierney2925 2 ай бұрын

axle nut was 30mm and wheel bolts 17mm AF. The brake calliper holder torx bolts are a bugger to get off, ended up using an impact driver.

@NikEastwood161 2 жыл бұрын

brill, I have a 207 diesel, its got a clicky CV joint and looking at mot history its the same side that had a split boot a couple of years before I got the car. I was worried it might be really hard to get the joint off the shaft but it looked in your video, quite easy. I think i am more happy to buy a new joint now instead of a whole shaft.

@minortinkering 2 жыл бұрын

Not a bad job to do really, best of luck. I’m sure you will manage it no probs 😊👍

@rrr...512 2 жыл бұрын

Great job. I too work on my driveway.

@andrewwmacfadyen6958 5 ай бұрын

Stretch boot and proper stretcher tool makes it a lot faster

@minortinkering 5 ай бұрын

They certainly do

@nunogarcia9446 Жыл бұрын

Great video, straight to the point! Do you use all the grease that comes with the kit, or do you only apply the amount shown in the video, and discard the rest? I've done a CV boot replacement before (1995 Astra Estate), filled the joint with grease (pretty much like you did) and squirted the leftover grease inside the boot. A year has passed, and while the boot doesn't have tears, and the clips are still in place (and tight, might I add), some (much) of the grease came off the boot (due to centrifugal forces) where the boot meets the CV joint. Am I just not supposed to use all the grease? Some videos show the leftover grease being used to fill the boot, some do not. Best regards, Nuno

@TheJohnson861 2 жыл бұрын

Don’t know if I dare give it a go 😱

@minortinkering Жыл бұрын

Definitely go for it , it’s not too bad to fix

@TheJohnson861 Жыл бұрын

@@minortinkering mines a 2010 petrol is it the same as yours??

@itsmephil2255 3 жыл бұрын

I like it,something different 👌 Dome CV boots before and they can be a sod sometimes

@minortinkering 3 жыл бұрын

Thanks Phil With cars there is always something that can go wrong of be a bit off a struggle, I think my biggest problem with this job was the weather it was raining the whole time and got really heavy when I was half way through 🙁 Best Wishes 😊👍

@itsmephil2255 3 жыл бұрын

@@minortinkering Iv shared on twitter and tagged HubNut in it He could learn a thing or 2 😂

@minortinkering 3 жыл бұрын

@@itsmephil2255 Thanks mate 🤣🤣

@jonka1 5 ай бұрын

I wish you had washed out the old grease as it will inevitably contain grit which will shorten the life of the cv joint.

@minortinkering 5 ай бұрын

It’s good practice to do so but this was just a quick case of getting the car done for a relative so the car could be re tested for the MOT If he was planning on keep the car I would have done so Best wishes Tim

@andrewwmacfadyen6958 5 ай бұрын

If grit or water in the joint the joint is already history

@6GSF 5 ай бұрын

hi tim, why did you have to replace the boot if it isnt split, why not just pump more grease in and seal it up

@minortinkering 5 ай бұрын

Hi The boot had been loose and leaking for a little while, the boot had gone soft and baggy and would no longer fit nicely back on the joint Best Wishes Tim

@peteisi113 Жыл бұрын

Hello Tim, is the cv boot supposed to move over the joint when turning, no matter how tight i get it the rubber boot seem to be sliding over the joint when i turn the steering.

@SchoolTutor 2 жыл бұрын

wow, thanks - do you have your own grage? this is exactly what I need to happen to my car :)

@minortinkering 2 жыл бұрын

Hi Ginny No I don’t but I have worked in a few over the years, I have been in the motor trade all my working life . Hope you get the repair sorted it’s not a bad job to do really ! Best Wishes Tim