Daikin VRV3 | error E4

No video

Daikin VRV3 | error E4 | LPS switch

Рет қаралды 19,759

2 жыл бұрын

Brand : Daikin VRV3
model : RXQ10PY1
Error: E4
E4 : Low pressure is too low(LPS Activate)
- The refrigerant piping system could be clogged, there may be insufficient refrigerant, or the LPS switch could be faulty.
#bonmj #daikin #vrv

Пікірлер: 71

@marcosMartins-wn8vn Ай бұрын

Marcos from brazil .Very good your work ,congratulations

@BonMj Ай бұрын

Thank you very much!

@j26a24d 2 жыл бұрын

congratulations for your great job of teaching others now that this technology is entering new york city due to its high demand and few technicians to make repairs congratulations although I don't speak Spanish but I understood your concern why others learn repairs and how to identify the errors and solve it thanks

@BonMj 2 жыл бұрын

Thanks

@KuntalGhosh 2 жыл бұрын

He is speaking Japanese.

@nazimsaifi2742 2 жыл бұрын

Hi. Bon mj I am your subscriber Thank you so much your videos is Very informative and I am also working in daikin Mitsubishi LG O.gerenal vrv & non vrv air conditioner I have 8years experience Installation and maintenance

@asangajayalath1665 2 жыл бұрын

Congratulations..Mr bon. Great explanation...

@BonMj 2 жыл бұрын

Thanks bro

@rdenir 2 жыл бұрын

Great Job Bon as always

@BonMj 2 жыл бұрын

Thanks bro

@Rameshprashanthi143 2 жыл бұрын

Iam come to Sir daikin itc bhadrachalam

@JuanTodoli 2 жыл бұрын

Great job Bon.

@BonMj 2 жыл бұрын

Thanks

@desmondteo6223 2 жыл бұрын

Well done Mr Bon

@BonMj 2 жыл бұрын

Thanks bro

@16valve64 2 жыл бұрын

Good job bon

@BonMj 2 жыл бұрын

Thanks

@hanyaberbagi9124 2 жыл бұрын

Nice Mr Bon , say hello from BALI

@BonMj 2 жыл бұрын

Thanks bro

@samhaazratechnicalsupport Жыл бұрын

Good jon 😘🇮🇳

@BonMj Жыл бұрын

Thanks

@karimchiu7527 Жыл бұрын

thanks sir Bon

@BonMj Жыл бұрын

Welcome

@alanwong2761 2 жыл бұрын

Bro are you release all of the gas or carry out refrigerant recovery before cut out low pressure sensor?

@j26a24d 2 жыл бұрын

Wow Singapore congratulations nyc new york city 🍎

@BonMj 2 жыл бұрын

Thanks bro.

@uyexdu4646 Жыл бұрын

Hi sir Bon, did you pump down when you replaced the pressure switch?

@j26a24d 2 жыл бұрын

Hello, we see it as a simple repair, but it is a job that takes several hours and knowing or having the capacity and the original parts to solve the error because it is not working and its replacement. I need you to teach how to solder the pressure switches so as not to damage them in the installation or silver solders the vacuum and recharge the unit with freon new minds because it is not in the video the freon leaks into the atmosphere it is not collected for its new uses another Once it is loaded with new freon and how to load it and know when it is at its normal capacity. Thanks a lot

@aungthiha5050 2 жыл бұрын

Hi Bom, may i know where did u get that s brazing cylinders set? I would like to buy in Singapore also. Thanks alot.

@BonMj 2 жыл бұрын

Teck Hoe AirConditioning Parts Pte Ltd 8 Lorong 15 Geylang

@elikirecycling5128 2 жыл бұрын

Did you repair it in the same day?

@goparismail9727 2 жыл бұрын

sukses selalu bos ku good 🙏🏻

@BonMj 2 жыл бұрын

Terima kasih master🙏

@mctesb5830 2 жыл бұрын

阿舅

@mac0pod 2 жыл бұрын

Hi. I have problem with my Daikin (C9 error). What is the value of the thermistor in the device: FCAHG125F? Thank you for your help!

@BonMj 2 жыл бұрын

Try to check R1T (for ceiling cassette,air thermistor is seal type,remove the wire clip and measure) Example temperature 30° is 16k ohm+- temperature 10° is 40k ohm+-

@mac0pod 2 жыл бұрын

@@BonMj Thank you very much for your answer. It was corroded. I replaced it. I gave a value of 20k (in 25C, it is about 16k in 30C). The air conditioning started to cool but only for 10-15 minutes. Later, the outdoor unit turns off and the indoor unit only acts as ventilation, no cooling. After disconnecting the power and connecting, the cooling works again for 10-15 minutes and turns off (and the room is still hot). Heating seems to be working normally. Do you have a solution?

@BonMj 2 жыл бұрын

@@mac0pod do you check all thermistor reading.like liquid pipe thermistor or gas pipe thermistor

@peramaraj2763 2 жыл бұрын

I have one doubt sir Mitsubishi electric VRF how to test run and how to set group address

@peramaraj2763 2 жыл бұрын

Please explain sir

@dayachauhanrajput4967 3 ай бұрын

Hi 👋

@mdrajib5119 2 жыл бұрын

Sir now I am working in Saudi Arabia. But I went to work with you. It's possible?

@nurfirdausabdrahman8487 Жыл бұрын

Before change that sensor, are we need to take out all the gas ?

@BonMj Жыл бұрын

CU only

@nurfirdausabdrahman8487 Жыл бұрын

@@BonMj i dont understand

@truthmatters6719 Жыл бұрын

@@nurfirdausabdrahman8487 outdoor unit,I guess you should do recovery or pump down if Daikin allows it

@vladimirodessitt7807 6 ай бұрын

Thanks 🙏🏻

@BonMj 6 ай бұрын

You’re welcome 😊

@ahmadzahir9959 2 жыл бұрын

Hi sir. Can i get the address on where to buy the heatblock compound

@BonMj 2 жыл бұрын

You can buy online

@user-ss5ww8sw7p Ай бұрын

Hello dear

@BonMj Ай бұрын

Hello 😊

@hidayaturrokhman3538 2 жыл бұрын

hey mr bon it's vrv 3, single outdoor kah ?

@BonMj 2 жыл бұрын

Yes

@DwiSeetyawanPKG 2 жыл бұрын

Hello sir, if cut the pipe, no leak refrigerant ?

@rdenir 2 жыл бұрын

Yes the Refrigerant will leak out.. Anytime you tap into a refrigerant system you would need to reclaim/recover the refrigerant.. This is one of my major gripes with Daikin, just about every other manufacturer uses a 1/4 flare male/female for the pressure switches yet Daikin still have this ridiculous setup which makes you recover all refrigerant before replacing the HP switch..

@BonMj 2 жыл бұрын

👍👍

@rohanpererabls5821 Жыл бұрын

Dear Mr. Bon. Thank you........ we are every day updates ..I am srilanka..........

@priyeshsingh2507 2 жыл бұрын

Sir Daikin vrv 4 coming error f4-04 please how to solve problem

@rdenir 2 жыл бұрын

F404 is “First Slave Outdoor Unit Compressor 1 Liquid Compression Error. This is stating that the system has detected a low discharge superheat across the First Compressor (M1C) of the First Outdoor Unit. This unit detects this by monitoring both the Suction and Discharge temperature and is triggered when the suction temperature falls below 3degC and the discharge superheat is below 10deg C. The most common issue that causes this to happen is the outdoor unit having liquid refrigerant flooding back to to it from the indoor units. This is only an Error Code and will allow the system to continue to run.

@BonMj 2 жыл бұрын

👍👍

@priyeshsingh2507 2 жыл бұрын

@@rdenir how to solve this problem sir. please Sir what am I doing this problem solve.

@rdenir 2 жыл бұрын

@@priyeshsingh2507 are you a technician? If not it would be very difficult to explain how to fix the problem

@priyeshsingh2507 2 жыл бұрын

@@rdenir yes I am technician.but vrv first time troubleshoot. So please help me