Dana 44 Spindle Bearings and Seals (True Spirit #20)

  Рет қаралды 8,236

Yoshimoshi

Yoshimoshi

Күн бұрын

If you've got your Dana 44 apart, you might as well change the spindle bearings and seals.
Seal Driver Set: amzn.to/3XTpDnh
Spindle Bearing and Seal Set: amzn.to/3IL2i2E

Пікірлер: 22
@35ppt
@35ppt 11 күн бұрын
Great video! My spindle sheared off at the inside bearing while underway sending all the parts out into the world. This video is invaluable. Thanks!
@YourAlaskaGuide
@YourAlaskaGuide 10 ай бұрын
Thanks, just what I was looking for. I took my old spindle out wanting to replace bearing and seals but I was confused when ordering a replacement kit that the parts were not the same. This has really helped. Thanks again, BTW the video was direct and to the point with no BS I find with other videos.
@deweydodo6691
@deweydodo6691 Жыл бұрын
Thank you man, that thin rubber seal I was not sure which side went where.
@mikemahlen6472
@mikemahlen6472 Жыл бұрын
Thanks for making this video. Just nice to see it before doing it. 👍
@whatchacookin1096
@whatchacookin1096 Жыл бұрын
Fantastic videos, keep up the good work.
@markclement256
@markclement256 4 ай бұрын
Hello, just found this very much needed tutorial. At 7:00 you reset the bearing deeper to make room for the v-seal but at 8:44 the bearing is flush.. Which one is correct, Please thank you.
@YoshimoshiGarage
@YoshimoshiGarage 4 ай бұрын
Good catch. It needs to be deeper for that seal
@moparnut6286
@moparnut6286 Жыл бұрын
Nice video good thing a have 3 pair of spindles as spares.
@michaelmangrum5460
@michaelmangrum5460 10 ай бұрын
As a machinist of 45 years I would use an aluminum bar for a drift punch on something as delicate as a needle bearing. Save the brass punch for heavier duty pieces.
@dirt1984
@dirt1984 3 күн бұрын
I’ve been trying to get this flange off with a torch for an hour lol
@lol123321123321
@lol123321123321 10 ай бұрын
You're actually missing a outer axle seal that sits between the roller bearing and that brass thrust washer. Most of the replacements are now Teflon or some other hard longllife plastic. I just rebuilt a early 70s Ford D44 and it was missing literally ever seal. They are all essential if you want to keep the hub water tight. As well as using the outer axle c-clip to retain it into the hub and preload the seals.
@YoshimoshiGarage
@YoshimoshiGarage 10 ай бұрын
Something other than the small seal at 8:24?
@lol123321123321
@lol123321123321 10 ай бұрын
​@@YoshimoshiGarageI stand corrected, it's there. My parts were a little different but all there. Excellent video for anyone else missing all the seals like I was. I just went off a picture of a parts diagram
@YoshimoshiGarage
@YoshimoshiGarage 10 ай бұрын
That seal was missing on both sides when I tore it apart
@CatastrophicFarms
@CatastrophicFarms 6 ай бұрын
Great video. Thanks for uploading. I think I may have messed up the first side I put back togethor. I pressed the bearing in further until it bottomed. I doubt the seal is going to make any contact with the Teflon ring. I don’t know if I should take it apart and redo it?
@YoshimoshiGarage
@YoshimoshiGarage 6 ай бұрын
I would probably just run it. It might be more prone to letting stuff in, and if so it will shorten the bearing life, but it's not likely to fail really fast
@CatastrophicFarms
@CatastrophicFarms 6 ай бұрын
Yeah it's already togethor now, I don't think it's worth starting over. If it fails I'll have it apart again in a few years anyhow. Thanks for the tips and the video. It really helped me out. I'll have the other side put together correctly. :)@@YoshimoshiGarage
@rosseowens
@rosseowens 3 ай бұрын
I did the same thing, good luck getting it out.
@michaelmangrum5460
@michaelmangrum5460 10 ай бұрын
My manual says to NEVER use the red grease on a Ford.
@YoshimoshiGarage
@YoshimoshiGarage 10 ай бұрын
Interesting. The "red grease" is simply Mobil 1 synthetic, which was invented long after this axle was produced, and this axle was used in Ford, Dodge and Chevy (and AMC, Jeep, and who knows what else). Maybe your manual is referring to a specific type of grease that was more common back in the day. Color is more a branding than anything meaningful any more.
@damnimcooltom1
@damnimcooltom1 Жыл бұрын
Beat it with steel! That's what I always say...
@markclement256
@markclement256 4 ай бұрын
I found this further down in the thread @YoshimoshiGarage @YoshimoshiGarage 5 months ago That seal was missing on both sides when I tore it apart. Question, So is there a v-seal in the hub and a v-seal on the spindle?
Dana 44 Wheel Joint Replacement (True Spirit #19)
12:37
Yoshimoshi
Рет қаралды 6 М.
Dana 44 Pinion and Carrier Installation (True Spirit #18)
14:54
Yoshimoshi
Рет қаралды 12 М.
DAD LEFT HIS OLD SOCKS ON THE COUCH…😱😂
00:24
JULI_PROETO
Рет қаралды 12 МЛН
Best KFC Homemade For My Son #cooking #shorts
00:58
BANKII
Рет қаралды 50 МЛН
Happy 4th of July 😂
00:12
Alyssa's Ways
Рет қаралды 63 МЛН
Самый Молодой Актёр Без Оскара 😂
00:13
Глеб Рандалайнен
Рет қаралды 3,1 МЛН
Engine Lathe Headstock Rebuild / Spindle Bearing Replacement
32:16
Watch Wes Work
Рет қаралды 183 М.
Building a New Process 435 Manual Transmission (True Spirit #35)
25:36
How To Replace Inner Axle Seals
17:03
OutJeeping
Рет қаралды 217 М.
Front D44 Wheel Hub: Reassembly
32:26
Dr. Bob's Last Chance Garage
Рет қаралды 17 М.
MINI LATHE UPGRADES #2: ANGULAR BEARINGS UPGRADE
13:59
HARRIS
Рет қаралды 11 М.
Ford Bronco spindle bearings and seals replacement part 1
12:46
Rotary Valves Make Normal Valves Look Silly - Why Aren't We Using Them?
17:14
driving 4 answers
Рет қаралды 1,9 МЛН
зил
0:32
Karol tv
Рет қаралды 512 М.
МИНУСЫ ВЕЛОСИПЕДА ФЭТБАЙК #shorts
0:16
Леха МАК
Рет қаралды 272 М.
Комфорт в Нива 2131  #offroad
0:18
Shorts - David Avanesov
Рет қаралды 1,5 МЛН
Is this a Race? 😱🔥 #shorts #shortsvideo #trending #motorcycle
0:19