DC-DC CHARGER RUNAWAY DISCHARGE WARNING.

Рет қаралды 114,823

4 жыл бұрын

THE EXPLANATION IS HERE:
This is not a problem I’m trying to solve. And neither is this a mystery as to why it happened. My diagnosis has been verified by professional auto electrical and DC charger manufacturers. It's not my opinion. It's my EXPERIENCE. And this is a warning to those who may be interested. NOTHING MORE!
If you charge the starter battery with AN EXTERNAL charger, the DC-DC will. WILL. OKAY. IT WILL . . . activate itself and begin charging the aux battery. THIS IS HOW DC-DC CHARGERS WORK!
If the external charger's capacity is less than your DC charger's it will drain the start battery in the process of charging the aux battery. IT WILL! This is also logical.
If you use a trigger cable from the ignition, and you leave the ignition on with the engine not turning, the DC charger will stay on until a pre-determined low voltage is reached, and switches off. That voltage may be too low to start the engine. I'm not guessing.
Now, you will only know if the full starter battery discharge has happened IF AND ONLY IF the charge is interrupted BEFORE THE CHARGE OF ALL BATTERIES IS COMPLETE. If you do not interrupt the charge, you won't know and all will seem fine. But the start battery has undergone a full discharge and recharge.
So. To avoid a runaway discharge, just charge the aux battery first. It's that simple! Or you may be caught with a flat start battery.
Now if you disagree, get this. There is nothing to disagree with! I am recounting an experience and presenting a warning. Use it OR don't use it. That's for you to decide.

Пікірлер: 487

@adriaanvanniekerk6322 3 жыл бұрын

As an Electronic technician here is some good advice for you. Never , ever charge your battery in your vehicle with an ac wall charger while it is connected to your vehicles electronics. The reason is that if for what ever reason you would have a voltage increase from the mains power or thermal runaway then you would fry your vehicle electronics. Always remove the vehicle positive terminal from the battery. You can however jumpstart from another vehicle like you would be doing right now. DC to DC chargers is for DC to DC.... not AC to dc to dc.. If your vehicle battery only was flat then you will need approximately need 10 to 15 hours on 10 amps to charge the first battery. Adding more batteries does double and triple the charging time. For an example. Drawing 10 Amps for 2 hours from a 100 amp hour battery means that you have used about 20% capacity. Charging the same battery with 10 amps will not fully charge that battery within 2 hours because as the battery gets fuller, the amps drop to eventually you will only be charging at about 1 or 2 amps. The time taken to charge the battery will be at least 8 hours.

@mickellis8747 4 жыл бұрын

I have the solution for you Andrew. I tow a camper trailer and in it I have a redarc BCDC40 to charge the two 100 Ahr AGM deep cycle batteries simply because of the distance from the car alternator and the resulting voltage drop. The problem is exactly the same, if the batteries in the camper were not fully charged when you stopped the DC to DC would drain the auxiliary battery to charge them. To overcome this I have a 100 amp relay mounted in the back of the car prior to the anderson plug which is switched through an oil pressure switch so it will never charge from the cars auxiliary battery, in my case, unless the car is running, even if you leave the ignition on accidentally. Luckily I found this out when researching the wiring and installation of the dc to dc charger before the actual fitting and it works perfectly. You could do a similar thing in your vehicle.

@4xoverland 4 жыл бұрын

This is not a problem I’m trying to solve. And neither is this a mystery as to why it happened. It can and will happen to anyone using a DC-DC setup. It's the nature of how DC chargers work. All of them with the exception of those relying only on a trigger wire. The solution is to charge the auxiliary batteries first. It's that simple. When I learn something, I like to share it.

@Cuppa500 3 жыл бұрын

@@4xoverland I charge the aux batteries first. I have 360ah batteries charged via solar /Redarc BCDC1240. I also have a built in 30amp Victron mains charger, connected to the Aux batteries. If I ever need to charge the crank battery (which is rare) I have an alternator friendly switch to parallel the aux & crank batteries via 70mm2 cable (for extended electric winch use) , but it also doubles as a means of charging the crank battery when switched to parallel.

@paullee2561 4 жыл бұрын

All good info Andrew, I have had many problems to solve with battery issues as well. But I must say that it has been about 50 years since I left an ignition turned on with the motor off. I always use the trigger wire and a solenoid to connect the BC-BC. Cheers! Good Stuff!

@seankearney6915 3 жыл бұрын

Many thanks for the heads up on this. Just a couple of weeks into a van to camper conversion. I will add in an isolator in the circuit just to be sure. I was always taught never to leave the ignition on, that stems back to old petrol cars where depending where the points were your coil could burn out. We used to pull the coil wire off if we had to tow a dead car for the same reason.

@DIESELTECH_ZA 4 жыл бұрын

I'm a firm believer to always isolate a battery when using a 220V AC charger, regardless whether using 1 or multiple battery systems. It simply eliminates any possible issues from occurring. Thanks for the heads up Andrew! :)

@kevinbinnie6192 2 жыл бұрын

This is so critical: as is clearly shown by Andrew's example. It's also the safest approach. I'm also a bit surprised at the notion of using solar to charge the crank battery. I'm more used to using solar and DC/DC chargers to charge the house batteries and isolating the crank battery so there are no loads on the crank battery other than originally intended by the manufacturer. The alternator should always be sufficient to charge the crank battery. Some alternators supply a varying amount of current, depending on their temperature.

@noodlefoo 2 жыл бұрын

Same here. If I am going to charge my starter battery with AC charger or solar panel, I always disconnect the wires from the negative terminal of the starter battery first.

@gregpaulsen9088 2 жыл бұрын

Thank you Andrew I have just discovered your channel. This should end a long running debate among my friends. I had warned one of my friends that sitting on the beach listening to the test cricket will flatten your battery. It had happened to me. I suspected the trigger wire as you explain but he was adamant that the load from the radio could not possibly drain his starter. Sure enough I had to give him a jump start but he still didn't believe it was the radio at fault. Now we know it was probably a flat auxiliary combined with the the trigger wire connecting the two batteries.

@darwiniandude 2 жыл бұрын

Fascinating! Thanks for sharing your knowledge. This situation is certainly not one that people would immediately expect to occur. I’m about to design and roll out a system into a 4WD van and I will certainly put an isolation switch between the crank battery and my custom goodies - even just if starting with jumper leads etc I don’t want the aux system taking some of that load away.

@darwiniandude 2 жыл бұрын

Oh - before I forget, and hopefully this helps someone - I reckon if you want to hook up that ACC wire to trigger the DCDC, hook it up to Ignition / ON position instead. That way if you’re sitting in the car in ACC mode listening to the radio, your crank battery isn’t being drained to charge the aux battery.

@DavidLaFerney 3 жыл бұрын

Good to know. I knew there was a reason why I hooked up the optional manual disconnect switch. Thanks! In my case I’m charging a travel trailer with the tow vehicle - so the protocol needs to be always unplug the umbilicals when not needed.

@jasonpotts6490 Жыл бұрын

Great video, Andrew and some excellent tips for us all. I'm using a manual cutoff switch in the dash for the DC-DC charger so that I can override the charger even when igintion is on.

@paullee2561 3 жыл бұрын

Another good video thanks Andrew. What I did was to install an old school 2nd battery solenoid, the old silver can type which only activates when the ignition is on. And yes you do have to charge the deep cycle separately if it is low. Cheers.

@jmarsison4191 4 жыл бұрын

Glad you shared this. Thank you Andrew.

@sleeharvester 4 жыл бұрын

Love what you are doing with this series Andrew! Could you do a video on what compulsory maintenance we should be doing before trips? I am not very Mechanical savvy and would love a guide. Thanks.

@RiveraD1988 4 жыл бұрын

Thanks for the info. In my situation I have my start battery purely for starting only. (Nothing connected besides low amp accessories on switches) the start battery will also be monitored. Then from my starter battery, it then connects to a smart isolator before connecting to my secondary battery. The second battery then has all the niknaks. This works only for older cars.

@FastFless 4 жыл бұрын

Andrew, this doesn't make sense. I have basically the same setup and haven't experienced this problem. Typically DC/DC Chargers will switch off and stop charging the aux battery when the input drops below 11.8 volts. They typically won't turn on unless the input voltage is above 13.1 volts. So when you connected your mains charger to the battery, yes the voltage would have risen above 13.1 volts and the DC/DC charger would have turned on. This is the same principle and operation of the old Voltage Sensing Relays (VSRs). However, it's understandable that your mains charger would not have been able to cope with the load (current draw) of both batteries (if both were discharged). But what should have happened, is that the voltage from your mains charger would have progressively dropped as it wouldn't have been able to maintain the output current required to charge both batteries. Once the mains battery (with mains charger connected) dropped below 11.8 volts, the DC/DC charger should have turned off. The mains charger would then have been able to again start charging the main battery and the internal resistance of the battery would start rising and so would its voltage (Ohms Law). Once it reached 13.1 volts, the DC/DC charger would kick in again, and the whole sequence would start again. The end result over time, should have been that both batteries would be fully charged. So what's happened in your situation is a bit of a mystery.

@nickscurr7062 4 жыл бұрын

The charger would have been connected to the same terminal as the DC-DC, so the DC-DC would've been seeing the input voltage of the charger this draining the battery. The charger would've been giving the DC-DC a false voltage reading of the main battery. The only way to get around this is to disconnect the DC-DC

@wikkidme755 4 жыл бұрын

Kim Flesser 240v charger pumps out a constant 13+ volts across the terminal therefore dcdc keeps charging..

@FastFless 4 жыл бұрын

@@nickscurr7062 My understanding is that external charger was connected in parallel to both the main battery and the DC/DC charger. So I still ask the question, why didn't the DC/DC charger turn off when the main battery and external charger voltage dropped to 11.8 volts. The external charger and main battery cannot have different voltages when connected together. Is there something here I don't understand? (I used to be an electrician...but not a very good one...LOL!).

4 жыл бұрын

@@FastFless I'm afraid there is some "misunderstanding" between the DC/DC and the small charger (like pulse charging in the small charger that causes the voltage to raise repeatedly above the DC/DC switchoff levels). It is actually very unfortunate that both the devices are from Redarc and they don't work together!

@tonymeredith6969 4 жыл бұрын

@@FastFless , if the 10 amp charger was a simple linear constant current 10 amp device, then I believe it should be just as you have described. There must be something funny about the way the charger is delivering the charge that is tricking the DC/DC charger into staying on. It would be interesting to connect an oscilloscope and see exactly what is going on.

@adamharvey3564 3 жыл бұрын

Thanks for the video Andrew, I remembered the tip a couple of weeks ago when I had to charge my start battery.

@Scott_69HemiDart 4 жыл бұрын

great info, Thank you! I am in the process of switching over my dual battery system due to the Tacoma smart alternator. This time I will place my second battery in the bed with a DC/DC charger............

@walterblackledge1137 4 жыл бұрын

Very good topic. Thanks for sharing!

@onedodger1 4 жыл бұрын

Thanks Andrew, I was wondering what my problem was as the Main battery was often low on voltage. After watching your vid I went and checked my set up and it was so. I am now going to instal a relay controlled by ingnition to circumvent this.

@bucket1249 3 жыл бұрын

No need to do that just put your battery charger On your house battery Once it Topped off it'll backfeed to your starting battery And charge it

@huntingarete9214 4 жыл бұрын

Awesome detective work ASPW. How many people have been caught out by this in COVID. I now realise that is what has happened to me two weeks ago.

@Offroader-gr 4 жыл бұрын

Very useful info Andrew, thank you.

@ingmarmaul4464 3 жыл бұрын

That‘s a very good one, have never thought about that. Thank you for sharing that one.

@Ozjourney 4 жыл бұрын

In my setup I have a breaker where your fuse is and I can quickly switch off the Aux circuit when I need to charge the main battery and often leave it off where not on trips just using the roof solar to keep the Aux topped up.

@4xoverland 4 жыл бұрын

NOTE. I chatted to the guys at Redarc and with Heiner. There is no mystery why this happened. It happened exactly why I said it did. It's a perfectly logical explanation. This is not a Redarc issue. I'm just using Redarc DC-chargers in my setup. All DC-DC chargers will do this because they rely on reading the voltage across the main battery to turn on. And if you use a trigger cable from the ignition, the start battery can be discharged if the ignition is left on, with the same result. The solution is very simple: if you have a DC-DC charger, if you want to charge the batteries without the engine running, charge the auxiliary battery first. What could be simpler?

@brettwako 4 жыл бұрын

Just follow the wiring diagram like everyone else and use the ignition trigger wire to turn the system on. If the ignition is turned off, no problem. Not sure why anyone would leave the key turned to ignition if the car isn't running.

@kadmow 4 жыл бұрын

So the solution - if you need to charge the start battery is to disconnect "aux" battery - before or after the BCDC - before charging the start battery (a good use case for a simple disconnect). (my BCDC Redarc 1225D is on Anderson connectors.) (NB - Redarc calls their system "Battery Charger Direct Current - BCDC, others call their units "Direct Current to Direct Current" Charger - DC-DC) Blue Trigger cable is specifically for low voltage / smart alternators.

@bennyfarrugia2419 4 жыл бұрын

4xoverland would a circuit breaker with switch work? Install near the mains battery and when you put on the charger flip the switch on /off

@MatejFabianek 4 жыл бұрын

I don't know if in any car. But in my VW T5 there is a D+ wire, which is a "alternator running" signal. From the factory the second battery charges only when the alternator is running. So not on ingnition. I thought there is a signal cable like this in any car.

@demolitioner962 4 жыл бұрын

@@kadmow seems like redarc are handicapping themselves for no apparent reason

@shanespicer6348 3 жыл бұрын

Very informative. Thank you.

@bder4255 3 жыл бұрын

Thank you Andrew that’s very useful review

@simplemanduke7128 4 жыл бұрын

Another great video Sir

@reismadeira7686 3 жыл бұрын

Nice work Andrew, If I may my 2cts: trouble starts when manufactors paralel batteries; the solution is use more powerfull ( more current) chargers, actually like they do sizing the alternator; of course the batteries last less. ( it happened in the past with 6v and the trucks 12v) best, Pedro

@oskarsfreimanis8192 10 ай бұрын

Thanks for good advice. I have’nt thought about. But you are right.

@PaulCreane 3 жыл бұрын

Wow, just wow, thank you for sharing.

@dontknowenator 4 жыл бұрын

Foretold is forewarned, thanks Andrew I would have killed my battery as well eventually and been scratching my head wondering why. And no doubt it would have been as the most inconvenient time imaginable. 👍

@dcocks 4 жыл бұрын

My Redarc does just the same thing, but the Ctek did not do it. Good job I have a charger isolator fitted in my truck

@adamarnold3154 4 жыл бұрын

Thanks Andrew

@PhatToni 2 жыл бұрын

Makes perfect sense, thanks. Simply put, attaching the external battery charger brings the voltage of the main battery over the 'turn on' voltage for the BCDC. The BCDC will start pulling current from the main to charge the Aux. It does so at a rate higher than is being supplied to the main battery from the external charger. If I ever do need to charge my main from an external charger, I will pull the fuse from between the main battery and the BCDC. Probably a good idea if jumping from one battery to another. Cheers

@patrickbuick5459 Жыл бұрын

Very interesting. I am working on upgrades to my Jeep and the dual battery setup and was going to get one of these.

@Chickengunny45 2 жыл бұрын

One can also add a switch on the positive lead connecting the redarc to your start battery. Turn it on or off to disconect the redarc to the starter battery and charge it without. Anyways, thanks for sharing the experience, dmuch preferablento learn it from you than in the trail.

@davep8664 4 жыл бұрын

Hi Andrew. I'd suggest re- approaching Redarc with regards to apsolute clarification as to this blue wire and voltage cut off. Someone has to be wrong, otherwise state of the art Redarc starts to look like well outdated Redarc (and any other dcdc charger that works in a similar way). I truly believe it's not Redarc as instructions despite not being so clear, suggest it's all down to this blue wire not being connected. Now a great video would be to connect the blue wire and do the same test, then try with the ignition left on to test voltage cut out, or as the case may be no voltage cut out with a mains charger connected.

@4xoverland 4 жыл бұрын

@davep8664 4 жыл бұрын

@@4xoverland Yes true, it is a simple solution. However I'm more thinking along the lines of alternator output - I'm running a smart alternator as fitted by Mr Toyota, if I remember correctly you have changed yours or was that just the Africa terrain tamer build? So a smart alternator can drop output to something like 8 or 9 volts, is there a scinario where by your starter battery can be fully charged in the eyes of the smart alternator however your aux batteries are near depleted and the dcdc charger pulls your starter battery down to a point where by it can no longer start your engine despite the alternator still effectively charging? My theory is the smart alternator should be smart enough to figure this out and fast enough/be able to provide enough amps to starter battery to cope. Scinario 2 - your alternator becomes defective and cannot provide enough amps to keep your starter battery topped up, the dcdc charger will happily help kill the starter battery much quicker, this drops to a point where your vehicle electrics cannot run and your lose engine and all "factory" vehicle power. (It would happen anyway but the dcdc has made it happen much quicker. O.k. alternator failure isn't that common without warning and if it did happen your red dash charge light comes on so you can pull the dcdc fuse and potentially divert solar power to give the starter battery some form of charge - that would be pretty pointless in the U.K though, with our weather! Perhaps I'm overthinking the perfect storm combination? I think I'm into my 6th or 7th year of unbroken patreon support for you Andrew. Keep doing what you are doing, we all get a great amount from your videos. I truly like the fact you are unbiased and not worried about saying the truth. Do you have any future trips planned with Mr Paul Marsh? Stay safe and let's ride this storm out one way or another...

@nzmarkb8713 4 жыл бұрын

Great lesson for us all, thanks Andrew

@glenecollins 4 жыл бұрын

How is the apparent charging voltage being maintained? As soon as the 50amp charger turns on it should pull the voltage down to just the battery voltage plus a little for the amount of power the charger can put in. Unless the DC to DC charger is set to run down to 13.2V or something that shouldn’t let the starter battery discharge to below where it can crank over your cruiser. If it is set to a very low cut off Voltage there should be a way of turning that up, with your setup the charging voltage shouldn’t fall below about 14v. Try measuring the voltage at the starter battery with theAC to DC and the DC to DC chargers running

@dcocks 4 жыл бұрын

Mine does just the same as Andrew says

@glenecollins 4 жыл бұрын

David Cocks yep I saw a bunch of comments saying they were doing the same thing and I definitely believe it but I don’t see why you would want it to keep charging down to less than 13.5v probably higher if you have a powerful alternator the little 70w one in my ute easily holds 13.5v at 50A draw (I checked) and that is where I set my minimum. I only have a 5A charger and a 50A charger for AC the 5A only adds about 0.25V if the DC to DC is working flat out. But I can see a 10A one allowing the battery to go down below 12V with a 50A DC to DC one running if the DC to DC goes down to a really low voltage before shutting off. (my DC to DC is a dodgy Chinese one with a potentiometer each for the charging voltage cut offs (start-stop, drop, fast charge, slow charge) and dip switches to select other stuff and it says it will do 45A but it only does about 30 on any battery setup I have tried it on.

@fowletm1992 4 жыл бұрын

The battery charger is sending 14v 10 amp into the battery The 14v triggers the dc/dc the drain The dc/dc is only looking for 13v so.even thoigh the main battery is dead flat the charger is providing that voltage signal It could maybe be set to trigger a fault because of low amperage input but currently they're only set to look for that voltage signal

@CampX4 4 жыл бұрын

Glen Collins, I do agree with you. It is impossible, voltage must drop the moment the load exceed the maximum Amp the AC charger can supply. But the question remains, how does the crank battery then discharge? It just does not make sense?

@grantkerr2971 4 жыл бұрын

CampX4 & Outdoor TV it’s being pulled out of the battery by the red arc DCDC and milking it flat as the 10 amp ac charger is trying keep up with THE 50amp load pulling through to the auxiliary, whilst this is going on the ac charger constantly sees a huge hole, tries in vain to fill it and cranks max voltage and amps into the bottomless pit.

@GizmosBushEscapes 2 жыл бұрын

very interesting. thanks for sharing that great tip.

@dirktheron3425 4 жыл бұрын

I love DC-DC chargers, but thought it to be common sense to isolate the primary and aux batteries before connecting a 220V charger anywhere in the system, even if charging the aux battery/s and the DC-DC charger won't let current through to the primary. I always run a 12V 60A circuit breaker between the two battery systems, this way you can even use two 220V chargers at the same time to maintain both sets of batteries whilst the vehicle is not in use for some time.

@DIESELTECH_ZA 4 жыл бұрын

Agree Dirk, Isolation prevents any 'oops moments' , simple and effective. :)

@Michael_Mears 4 жыл бұрын

Agreed. Circuit breaker to isolate. Simple and effective.

@stevenarango461 2 жыл бұрын

great information thank you.

@TheAussiebloke87 4 жыл бұрын

U should have ur BCDC charger on the trigger switch u mentioned. The trigger switch can also be connected to a wire that only receives voltage when the car is running. U could also add a breaker so as the BCDC charger doesn’t see the voltage when ur trying to charge ur main......

@bennyfarrugia2419 4 жыл бұрын

Not an issue with CTEK 250sa with smartpass check it out ! Have had ctek on my cars now for 7 years and never flat batteries, and my car is not a daily driver either.

@B4x4 4 жыл бұрын

That solution will also charge the start battery by solar when aux battery is full.

@paulbarnard5267 4 жыл бұрын

CTEK also recommend attaching the float charger to the Aux battery side. The same can happen with CTEK if your float charger is able to lift the main battery voltage.

@timhenkels8506 3 жыл бұрын

Ģg^g^gg^^v

@andrewjack3498 4 жыл бұрын

I am in the process of changing my VSR for a 20A DC-DC, I was planning on using a DPDT switch or relay so that by default the camping batteries, when above trigger voltage (ie being solar charged) will keep the start battery full. When the vehicle is started, the relay will be triggered (by ignition switch) and reconfigure the DCDC to charge the camping batteries effectively from the alternator.

@munecito 4 жыл бұрын

Andrew keep the VSR and and the DC DC charger behind. It isn't costing you any extra. Just apply the following wiring from redarc as if your DC DC charger was not in the same vehicle and that way you have a redundancy for cut off circuit. www.redarc.com.au/wiring-diagrams/how-to-wire-bcdc-caravan-vehicle-variable-voltage-alternator I wired the my wife and mine car like that because hers has a smart alternator. The DC to DC charger is attached to the portable battery box. If I didn't add a VSR to my car the charger would be draining my main battery too much. For hers to work she needed a VSR anyway. It was that or adding a switch to the portable battery box to turn on/off the blue ignition wire of the charger. But there would have been the problem of forgetting to do it and either arriving to a destination in her car with a not fully charged battery box, or flattening my battery overnight because of the low DC DC charger voltage cut off.

@taranis616 3 жыл бұрын

I honestly thought everyone knew this....The clue is in the ‘voltage sensing’ aspect of the DC-DC. Also, DC-DC does not charge at 50 amps. That is simply the maximum it can charge at. The charge delivered depends on the aux battery’s state of discharge.

@DrDubstyle 2 жыл бұрын

I typically see 5ish amps from my alternator? Would you say thats pretty low? I do have issues with power as dashboard and electrics turn off 10mins into night driving and come back on with battery light

@petcuyvers Жыл бұрын

Yeah, if only charging at 5 A most of the time you seem to have an alternator or bad starting battery issue.

@kellyoconnor9773 Жыл бұрын

Thanks for the video. I will now put an Anderson plug in my engine bay connecting from my main battery to my dc to dc charger so I can unplug it if I need to charge main battery.

@danieljackson9381 3 жыл бұрын

I was installing a BCDC 1225 this weekend, and found your clip pretty interesting. My install was in a camper, and it got me thinking… This issue looks like the starter battery needs to be better isolated from the house battery, and possibly it makes sense to treat it like a camper install and use a solenoid or an SBI to only link them when the ignition is on?

@carltunstall1989 4 жыл бұрын

Thank you Andrew, I always follow your channel with great interest and I particularly appreciate your willingness to share freely your knowledge and insights. I would be equally keen to hear expert opinion from Redarc on your observations. Presuming you have this would you share those with us too perhaps?

@mikehayes131 4 жыл бұрын

Carl Tunstall shame his information is often incorrect, omits important details or is a bias of his ignorance (take the ARB TPMS video for instance)

@carltunstall1989 4 жыл бұрын

Here’s what Redarc said.... In regards to the connection of the blue trigger wire on BCDC, the following needs to apply: 1) If your vehicle has a standard alternator type (fixed voltage), the blue wire can be left disconnected 2) If your vehicle has a smart alternator type (temeprature compensating or variable voltage), the blue wire needs to be connected to an ignition source 3) If you are unsure of what alternator type you have, it is best to connect the blue wire to ignition We have indeed seen the video mentioned and it does explain the connection of the blue wire, just not in great depth as to how it operates.

@billroach2393 4 жыл бұрын

Andrew, I realise you've identified the issue, but here's a suggestion for the future. I've fitted an Enerdrive 240v charger in the canopy of my Silverado. It has 3 separate "channels" for charging 3 separate banks of batteries. I have a somewhat similar set-up to you... A Redarc BCDC1225L and solar panels on the roof of the camper. When I plug the 240 volt cable into the caravan-style receptacle, the Enerdrive charges the Lithium battery, which is set to Channel One (in the canopy) first. It has the ability to choose what type of battery is being charged. Once the lithium battery is charged, it then turns its attention the Channel Two, which is the twin under-bonnet starting batteries. To achieve this latter function, I've simply tapped the Channel Two supply line into the cable that supplies the BCDC with its power from the front batteries. In your case, if you go ahead with another lithium battery (inside the canopy of your truck), then you can utilise all three separate channel of the Enerdrive. If you're interested in my Chevy, here's a write-up that was done a year or so ago: loaded4x4.com.au/issue-002#61

@4xoverland 4 жыл бұрын

@seanfrost5804 4 жыл бұрын

Andrew, possible solution, mount a solar panel on your garage roof and run cables down for easy connect on to the yellow cable (solar input) on the Redarc. When the Redarc sense solar input, it will not accept input from the main battery. Therefore, as long as you only have your 10amp start battery charger on at the same time as the solar connected to the aux, then you will effectively have separated charging of batteries. Regards, Sean

@seanfrost5804 4 жыл бұрын

Another, solution, in the red line between the start battery and the Redarc, add an old style silver 100 amp continuous duty solenoid (the type we all used to used in simple dual battery set ups years ago) then trigger this from the windscreen wiper motor. Then, the start battery can only feed the Redarc when the engine is running.

@raymondxerri1408 4 жыл бұрын

i have no problems,my dc todc charger wont draw onece it reaches 10.5 volts,plus i use a dedicated deep cycle battery charger,it will charge two 120 amp hour batters plus the start battry,correct your set up.you may need a voltage sensative relay.

@4xoverland 4 жыл бұрын

@guylneedham 4 жыл бұрын

Interesting stuff, I shall check for this problem shortly! I noticed that your new vehicle has a cyclonic snorkel head/pre filter. What do you think of them? Will you be changing it? I'm considering switching from an air ram to a cyclonic head.

@davidswain7409 4 жыл бұрын

This is why I haven’t changed from my ‘old version’ SBI and use a mppt solar charger as well.

@michs1708 Ай бұрын

excellent vid, well explained. And very good to know.

@jaspersonnyoner 4 жыл бұрын

Since you're trying to centralise weight between the axles have you considered moving the start battery closer to the firewall?

@Sethjxl 4 жыл бұрын

Well spotted Andrew. This is a big problem with DC-DC chargers. The charger will continue to run when the car is switched off as the cut off input voltage is 12.4v. Once the input drops below 12.4v the charger will stop until it reaches 13.4, however this often means your primary/starter battery is sitting around %70 SoC which is not a good place to be when it comes to starting big engines. For example: You have a 110A alternator, 100A isolated aux battery, a BCDC1240 charger, and a fridge. You pack the fridge a few days before going away and its on full time to get to temperature. The only driving you're doing is to the shops and back, perhaps an hour a day. If it's just bussing around locally, your alternator never gets consistent high RPM so its average output is around 30-50A (most are

@OneManTrail 4 жыл бұрын

I run the trigger wire through a switch and to 12v+ that way I control when the DC-DC is on.

@terryedmondson3563 3 жыл бұрын

Hi i do similar ,plug into cig plug and works fine, cheers terry.

@Nathansillav 3 жыл бұрын

What happens when you use solar and the car is off

@OneManTrail 3 жыл бұрын

@@Nathansillav My solar batteries are separate from the vehicle, so it functions the same if the car is on or off.

@jackfourbee3609 4 жыл бұрын

👏👏👏👏THANKYOU.

@johndee68 2 жыл бұрын

Loved the way you explained this. Just a thought, doesn't this come down to the rule of using a battery charger that is of equal or higher current rating than that of the largest charger device in the vehicle circuit active at that time of charging?

@JELLYMOTONZ Жыл бұрын

thanks for the handy hint

@Red-cy4hl 4 жыл бұрын

I also have a Ctek 250sa DC to DC charger hooked up to a solar panel (because it's not a daily drive) it charges the 2nd battery and when that's charged it starts charging the start battery.

@inncogneato6341 3 жыл бұрын

Exactly. Take any overflow from auxiliary battery bank back to the starter battery. I’m looking at a dual-sensing VSR for this purpose. The Jaycar one has cut-in at 13.3V and cut-out at 12.8V.

@superformOG 3 жыл бұрын

helpful, i have asked the victron guys if it would do this with the orion dc to dc charger

@einfelder8262 4 жыл бұрын

This is really a new problem when the auxiliary battery is Lithium. Previously the AGMs commonly used would rarely accept 50 amps charge, no matter what the rating of the DC-DC charger. The solution is simple - if you can afford Redarc 50A DC-DC charger (most of us can't, and are perfectly well served with a 20A unit) you can afford a 50A AC battery charger. End of issue. You can also wire up a dash switch into the IGN trigger wire so you can manually override on those occasions when you need to leave the IGN on for long periods.

@4xoverland 4 жыл бұрын

@moneypitvan6378 3 жыл бұрын

Crazy. The auto-sensing circuit worked against you. Very informative. Thanks for the lesson.

@ErikKater 4 жыл бұрын

I have a TS800 DC/DC converter which has a vibrationsensor to check if engine is running, works fine, also when ac charger is hooked up. Except on a long trip on a ferry where it completely drained the starter battery 🤔

@adidas4275 Жыл бұрын

Good point. I am about to install a redarc DC/DC into my jeep with an AGM and LiFePO4 auxillary battery and I have been looking for a AC battery charger to do what you are doing.

@adidas4275 Жыл бұрын

you could use ignition wire vs voltage sensing on the DCDC

@jmfu 4 жыл бұрын

It may be worth noting that every time you charge this way you are depleting the crank battery far too much even if you leave it on for the full cycle. It's being drained way down then recharged slowly, bad practice. Better to charge house batteries separately.

@Michael_Mears 4 жыл бұрын

Yes, that's a better procedure / good practice.

@glenecollins 4 жыл бұрын

J M or get a DC to DC with a more appropriate cutoff voltage if you can’t change it in the settings.

@Scicluna83 4 жыл бұрын

Will this happen with duel sensing dc to dc Chargers my solar input on the dc to dc will also charge the start battery no need to connect solar to the start battery

@KeyMakers 4 жыл бұрын

Im not sure how you have done that .. but that is a setup issue .. its not a problem with DC to DC chargers buddies .. laughs .. oh dear

@gotoylc 4 жыл бұрын

Key Maker quite agreed. Setup issue. But can be solved if one wants. For me no.

@4xoverland 4 жыл бұрын

@@gotoylc This is not a problem I’m trying to solve. And neither is this a mystery as to why it happened. It can and will happen to anyone using a DC-DC setup. It's the nature of how DC chargers work. All of them with the exception of those relying only on a trigger wire. The solution is to charge the auxiliary batteries first. It's that simple. When I learn something, I like to share it.

@4xoverland 4 жыл бұрын

@blastar55m3 3 жыл бұрын

@@gotoylc if you understand how electricity works, you'll find that he is correct. It's not a setup issue

@gotoylc 3 жыл бұрын

@@blastar55m3 This is a very obvious setup issue. There’s a relatively simple device to install to prevent, 100%, this particular issue from ever happening. Unfortunately I do not know Andrews full setup, so perhaps the setup is not correct correct, or there’s an item overlooked and not installed. Andrews setup diagram would be useful on this issue.

@jjsadv 4 жыл бұрын

I dont charge mine like described, more the suggested way, Aux first then start.. So never seen this happen, But I had never thought about it. Interesting. Trick for new and old players alike.

@ismailmussa7432 4 жыл бұрын

Hey Andrew, have you considered an Auto Conversion on your 79 for this build? What are your thoughts on an Auto 79?

@krover01 4 жыл бұрын

Maybe Im just thick headed, but I just installed a Renogy DC to DC charger and second battery. The charger only turns on when it sees more than 13.2v for 30 seconds. I dont know about you, but my 2001 Land Rover Discovery does not put out 13.2v with just the ignition in the "on" position. Only when the vehicle is actually running will it put out more than 13.8volts and after 30 seconds of seeing that voltage the DC charger will turn on. If the starter battery goes down to below 12.7 the unit shuts off. The Renogy unit also has solar inputs and unlike the Redarc. Once the aux battery is full. The unit uses the solar to trickle charge the starting battery!

@4xoverland 4 жыл бұрын

@barefootbandit1 11 ай бұрын

I installed a switchable circuit breaker between the main battery and the DC to DC charger to separate the two Systems if I needed to. I did however learn the hard way about what you are talking about because I forgot to turn the switch off

@GregPalmer2 4 жыл бұрын

That's a good heads up on protecting your starting battery especially these days because a lot of new cars run their computer systems of this battery. When the main battery is drained the system needs to be reset and then comes the hard part finding passwords. This would be a nightmare if your in the middle of nowhere without a dealer or a auto electrician around. Solving this problem for you was good,your able to know how to fix it. I think it's a good idea for any 4x4 driver to practice these scenarios just in case it does happen. For me if l bought a new 4x4 l would disconnect the battery at home to see what would happen to the system.😁👍

@zaneh6224 4 жыл бұрын

Passwords ?, the only thing that needs resetting on my 2019 Ranger is the Auto drivers window, it resorts back to non auto, everything else works fine after a battery disconnection just like any decent 4WD should be, as the ECU'S have self powered backups inside, if a 4WD is designed like you say, then I would stay away from it.

@BJKAdventures22 2 жыл бұрын

Great video thanks, so the game changer has introduced problems for the non experienced installer 👍

@4xoverland 2 жыл бұрын

Yes. But it has more importantly made it one zillion times more efficient and easier to install for the non experienced installer. There is always a catch with great inventions. In this case the catch is a small one and as easy to solve as - charge the auxiliary battery first. What could be simpler?

4 жыл бұрын

I'm just curious. Since You have lithium battery at back, it would charge fast during drive. Is home charging for battery maintenance purposes only? Right now im buying DC/DC charger and after your video i think about redesign my wiring and leaving inside cyrix ct. As always, thanks for great video.

@papaloo2000 4 жыл бұрын

Connect the trigger wire through a relay. Pin 30 to key on power, 86 to key on power, pin 87a to dcdc trigger wire and 85 to alternator thin wire which grounds the battery warning on dash, so when alternator is working the DC DC will sense and turn on the charging.

@Michael_Mears 4 жыл бұрын

I thought 85 was the ground side of the relay...

@papaloo2000 4 жыл бұрын

@@Michael_Mears Ah, yes.. I just noticed the mistake. Corrected it now.

@vroor32 Жыл бұрын

Aah, good ol' relays ....I like this 👍🏿

@overlanddrive4389 4 жыл бұрын

I have a Victron DC- DC on my two auxiliary batteries,with a 10amp smart charger connected direct. No problem with batterys, alwayes fully charged.

@glennharvey5100 4 жыл бұрын

Overland Drive I use the same dual charger system for aux and main battery, just leave a shore line plugged in and both batteries are charged and maintained, easy. Worth buying a decent dual charger

@q8mechanic427 4 жыл бұрын

Even if you had the blue wire connected to ignition, Redarc will still sense an increase in main battery voltage and turn itself on. I noticed that on my Land Rover.

@jeffwisecarver 4 жыл бұрын

So how are you going to aleiviate the problem while still being able to charge both batteries in various ways?

@phililpb 2 жыл бұрын

very interesting.. Once you know this it is easy to avoid but like you I would not have thought of it first

@ChookChasersMX 4 жыл бұрын

Hence why I run a manual reset circuit breaker to my DCDC to stop it running while maintenance charger is on starter battery. There is always pros and cons even with circuit breakers and probably best to use a manual reset breaker in a dcdc charger case as an auto reset could keep toggling all day long if there’s a fault until it either burns it self out or something else happens. Another issue with circuit breakers and especially on a hot day under a the hot bonnet with high current is they can trip based on too much heat even if there is no over current or fault situation. Probably the most reliable type of system would be the midi fuse but then can’t break the circuit without maybe also installing a switch.

@oldmatesgarage2425 5 ай бұрын

Was kind-of aware of this but good to be told, probably could make a safety circuit for this but a Big Label on the charger will be the cheapest solution.

@DANIEL-ls5ku 3 жыл бұрын

So in short, connecting an external charger to the main batt. is the same as turning the ignition switch to on. The DC-DC charger could not tell the difference.

@MrBrenden830 3 жыл бұрын

Use a battery isolator connected to your ignition. Also a separate switch to the DC to DC so you can turn it off even when you ignition is on . When your ignition is off the isolator is disconnect and so is the DC to DC. Also my trigger switch is connector to the isolator. When its on and the separate switch is on so is the DC to DC when its when is off its off.

@davewalkerden 4 жыл бұрын

I believe my Renogy DC-DC won't start charging unless BOTH the ignition circuit is 'ON' and the seperate external Voltage Sensitive Relay senses the charge voltage. I'm pretty sure runaway discharge can't happen with my set-up unless I leve the ignition ON, however, I'm going to test it now that you've got me second guessing myself LOL

@UrbanCynic101 3 жыл бұрын

@4xoverland My solar panels are currently removed for vehicle maintenance so I have been charging exactly how you do (did). I have been monitoring voltage and current with the following observations. When the supply (crank) battery is at 14v with engine running the DC/DC charges at full current. With only a mains charger connected to the supply battery it's voltage drops and the DC/DC tapers off the current delivered to the lithium. (while still in bulk stage) It finds equilibrium at 7 amps and happily charges everything to float. This happens to be the exact amount of current my Ctek 7.0 is delivering to the supply battery. My DC/DC is not redarc. I would suggest either a setup error, a firmware problem or a bad design DC/DC charger.

@Michael_Mears 4 жыл бұрын

VIDEO RESPONSE to Andrew: please search for "Dual battery charging issues VR: 4XO DC-DC CHARGER WARNING. Avoid a runaway discharge." on youtube. Shows what some DC-DC chargers do when configured in similar circumstances.

@zaneh6224 4 жыл бұрын

What if you put a switch in the cabin to control when the charger is allowed to operate, normally it would be in the ON position so it can operate as per normal, but if you want to do work on the car with ignition on, for a period of time the switch will disable the charger, maybe a red flashing light also when it's "off" to warn you so you don't get to the destination and it's wasn't charging because you forgot to turn it back on ?

@stevep8773 4 жыл бұрын

So this occurs when the DC/DC charger senses the (higher) voltage but not low current output of a small charger, and then "decides" to charge the auxiliary battery, which is in a state of discharge? Interesting problem

@MrFanOFRacing 4 жыл бұрын

On an isolator setup redarc sbi12, charging both a start and dual purpose marine stoaway at the same time off a battery maintainer at 2amps. I have been separating them when stored in the shed would that be harmful with both on the one. Got a better 5amp victron one that would be easier to just plug into and do both. I know the isolator isn't as efficient but for a basic under bonnet setup that I wanted to be able to jump start myself it works good enough. Also add those large fuses are not the greatest usually the holders cannot stand up to the current, midi are far better and easier to store as spares

@mountainconstructions 4 жыл бұрын

This is why i've always installed a DC-DC behind a separate VSR Or relay that is operated by the ignition When maintenance charging at home, i connect to the Aux Batt via an Anderson in the rear

@carl.colleen.rover.adventures 4 жыл бұрын

That is exactly how I wired mine as well (relay operated by ignition in my case)

@nickboylen6873 4 жыл бұрын

Sounds like these expensive systems have plenty of traps if not set up or used right. For now, I just have a really cheap set up of the main battery for all the original vehicle systems (1970s Land Rover, so very basic), and a second battery for accessories like power sockets, stereo, auxiliary lights, seat and screen heating and so on, any thing not essential to driving. They’re linked by a heavy relay which it triggered by the alternator diode pack (dash warning light terminal on the back of the alternator). It works very simply, so the batteries are isolated unless the alternator is providing a charge. I want to add solar for the auxiliary battery. The primary shouldn’t need it - main systems are drawing power if the vehicle isn’t being used, and in such an unlikely event, the engine could be started by jumping (a hard wired isolator connecting only for emergencies) from the auxiliary battery. There is a lot to be said for simplicity.

@jvalentine8376 Жыл бұрын

You need a battery isolator between the two batteries so that when the main engine starting battery gets to fully charged then the rear battery is connected in parallel as one battery . Then the charger or the alternator only has to charge around half the potential amp hour capacity at a time . As soon as the isolator detects current draw and voltage drop on the main battery it shuts down and isolates the rear battery . Most have a jump start button that allows you to jump start from the rear battery if the main battery is dead . It also allows you to drain the rear battery running something but not drain the main starting battery . In any dual battery system it's better if both batteries are the same type and also very close in their amp hour capacity . I am not a fan of DC to DC chargers but if you use different chemistry batteries then they are needed . I could be wrong but I think they can overwork the alternator . Also not a fan of lithium batteries especially inside the cab . Just do a search for lithium battery fires in cars . AGM battery much safer and hold their charge well also cheaper but heavier .

@stevegoodwin5841 7 ай бұрын

How is starter battery connected to second battery?

@takeitforadrive 4 жыл бұрын

Completely off topic, but what tyres are you planning to fit on the rig? Great video as always!

@spudboy1328 4 жыл бұрын

He's fitted Falken Wildpeak AT3W's (I think that's the code).

@DallasD2.0 3 жыл бұрын

Awesome video, I get it. I am also having another weird problem. After using the fridge for the day and I get back in and drive, my dash lights start coming on. I am sure this is the computer shutting things down for lack of power. Sometimes it is when I underrate. When the second battery if full there is never any problems. I have 120 series Prado 3lt desire. I have wonded about the Alternator but am now wondering about the dcdc charger. Any thoughts?

@plc7957 6 ай бұрын

Use a mechanical switching relay also to isolate the front and rear. I also learned the hard way

@davidschumann4495 Жыл бұрын

What about attaching the blue trigger wire to the alternators output wire? Just a guess.

@JasonShepherd_01 4 жыл бұрын

If you pull 50amps from you starter battery, the voltage on the starter battery will quickly drop below 12.8V (or whatever) and your DCDC charger should sense that and switch off. Charger is puttting 10amps across, pull out 50amps - voltage will drop quickly. Mine does (Projecta DCDC). Why doesn't yours?

@kadmow 4 жыл бұрын

I think in this case the Battery charger was keeping the Main battery at a high enough voltage for the BCDC to keep pulling current out - it probably cycled several times sucking all the input "juice" out of the main battery. - could be wrong. (leaving it "nearly flat" over the charging time)

@brianostwald802 4 жыл бұрын

Use a smart amp solenoid simple men

@aussiedrifter 4 жыл бұрын

@@brianostwald802 Dead right Brian, I use the simple old smart voltage solenoid No Worries, why complicate a simple need with an expensive & complicated piece of Bling Mate.

@grantkerr2971 4 жыл бұрын

Jason Shepherd The voltage at the battery needs to lower than 12.7 for 10 seconds before the dcdc will shut off as it has a delay built in. Even if the ac charger dipped in voltage under load it would sense it and crank up voltage to compensate within that time window of 10 seconds and kick it up over 12.7 + , therefore dcdc charger keeps on pulling the load.

@munecito 4 жыл бұрын

@@aussiedrifter he needs the DC DC because he's running a lithium battery. The alternator with a VSR would cook the lithium battery BMS or the cells quickly plus the battery may even burn the alternator.

@servicebrisnorth8269 4 жыл бұрын

Andrew, you've just proven (thank you) that a DC-DC-charger is a redundant piece of "bling". All one needs instead of a DC-DC-charger is simply a $30 BIG FAT DIODE . OK, assuming you're also charging from the Solar-Panels, then you need a regulator for them, but a decent Solar charge regulator will do that cheaper than the DC-DC bling. Reason I say this is that the vehicles Alternator is a regulated charger of ample output. Now, you *could* in theory just join the 2nd battery in parallel with the car battery, and they will both charge just fine . -But we both know why we do NOT do that! - because they will both go flat together, too. And THIS is what the $30 diode is for - it allows the charge to flow only in the direction of the 2nd battery and not out into the car battery. Your Alternator has plenty capacity to charge both batteries simultaneously. the DC-DC inbetween is only duplicating what the alternator itself does. Moreover, its just wasting energy in the process. Just replace it with a diode, (and a $1 fuse if you want to go "pro version" ) and you're set (so long as you have a little regulator between your Solars and the 2nd battery). I'm all for keeping things simple in the bush. I don't need to explain why. Thanks for a great channel.

@4xoverland 4 жыл бұрын

@servicebrisnorth8269 4 жыл бұрын

@@4xoverland Fair enough. Either, as you say, charge the Aux batts first ... or ... get out more often - The problem we ALL have :-P