How to Solder SMD Components using Sand

Рет қаралды 1,880,627

5 жыл бұрын

This Video is Sponsored by Squarespace. Get 10% off on your first purchase by using this link! - www.squarespace.com/ddelectro...
Coupon Code: DDELECTROTECH
👉Order PCB's From PCBWay -
Limited Time Offer - PCB Assembly Fee Has Drop Down to Only $30. pcbway.com/
Hi Everyone, Hope you are doing great. In this video I will show you a simple trick to solder SMD Components on PCB, using sand. This trick allows us to solder small to big any size PCB within a minute.
🔧🔨The Tools I Use -
Helping Hand - ban.ggood.vip/8r0z
Soldering Iron - www.banggood.in/custlink/3mDK...
Hot air Station - www.banggood.in/custlink/KKGD...
Microscope - ban.ggood.vip/8r0o
Heat Resistant pad - ban.ggood.vip/8r0y
Sponge - ban.ggood.vip/8r0w
Teezer - F & E - ban.ggood.vip/8r0t
Paste - ban.ggood.vip/8r0s
Flux - ban.ggood.vip/8r0b
❤️Support us on Patreon -
/ ddelectrotech
Similar Videos -
Made My Own Tablet Computer - • How I Made My Own Tabl...
Made My Own Smart watch - • How I Made my own Smar...
Made My Own Smart Glass - • How I Made my own Smar...
Make a Microphone - • How to Make a Micropho...
Make a Stereo Headphone - • How to Make a Stereo H...
Make a Speaker - • How to Make a Speaker ...
Solar Generator - • How to Make a Free Ene...
We regularly uploads exciting videos like this
Suscribe us For More Videos - goo.gl/AmSeqY
------- Follow us on FaceBook ------- / ddelectrotech
------ Follow us on Twitter ------
/ ddelectrotech
#SMDSoldering#SolderSMDComponents#SandSoldering#SolderUsingSand#HowIMade#SmartSpeaker#AlexaGoogle

Пікірлер: 885

@corynrobinson 5 жыл бұрын

If you get a solder bridge, using wick can remove too much solder. Instead, try using a generous amount of flux to get the solder to go where it needs. If that doesn't work, then break out the wick and re-solder the appropriate pins.

@matiass501 5 жыл бұрын

No one : DD Electro Tech : I solder smd with sand

@leegami3234 5 жыл бұрын

Garbage meme.

@matiass501 5 жыл бұрын

@@leegami3234a meme is a meme

@Ebani 5 жыл бұрын

@@leegami3234 Do you even lift bro?

@pawelandrul 4 жыл бұрын

Chuck norris: i solder sand with smd components

@lakmalbandara368 4 жыл бұрын

good...

@tapanprsd1 5 жыл бұрын

induction heating can make some sensitive component damage. better to switch off the induction heater before keeping the pcb for baking or use simple temperature controlled heater.

@maxk4324 5 жыл бұрын

Or use a very thick iron pan so that it doesn't become saturated and thus acts as a magnetic flux 'shield' of sorts.

@Nic-st3mp 5 жыл бұрын

The induction power 1st doesn't go through the iron pan and 2nd it doesn't go through the aluminium plate. How should the pan heat up without absorbing the power? First think of physics.

@maxk4324 5 жыл бұрын

@@Nic-st3mp it might not necessarily absorb all the power is what I'm saying, if it saturates then the magnetic field will start eminating out of the pan. Of course it absorbs most of it or else the induction stove is broken somehow or operating at the wrong frequency.

@jeffgrills1101 5 жыл бұрын

If it only takes 30 seconds to melt the solder, you can easily unplug the heater before dropping in the circuit board. With sufficient sand you'll have a substantial heat reservoir.

@narendravadiya7219 5 жыл бұрын

@@maxk4324 It will do.

@eafindme 5 жыл бұрын

It's only applicable if all of your SMD components are at the top layer.

@vedantx-b2986 4 жыл бұрын

Smd mean surface mount components therefore all the components are on top layer only

@shubhamkasera7368 4 жыл бұрын

For that you can solder it in two cycles one by one for each layer

@Sky-jq2no 4 жыл бұрын

@@vedantx-b2986 you can have SMDs on the top AND bottom

@WurstPeterl 4 жыл бұрын

@Sky for Bottom side you must use BGA. SMD = SURFACE mount & BGA = BOTTOM attachment

@m4ki9h76 4 жыл бұрын

@@WurstPeterl / BGA is Ball Grid Array, which means the solder pads are beneath the chips, needing balls of solders&specialized tools to properly heat the solder and mount it.

@DimusTech 5 жыл бұрын

Totally learned something new today, thank you!

@sysghost 5 жыл бұрын

For those who wonder about the sand. It helps evening out the temperature, and also act as a heat buffer. One "can" place the PCB directly into the pan, but depending how the hotplate behaves, it is more likely to damage the PCB as the temperature goes up and down a lot as the hot plate power is cycled on and off. (The sand helps evening out this heat cycling). Simple, yet a fantastic idea with simple cheap parts one already have at home, or easy to get without any effort. All thumbs up!

@charleshines6155 5 жыл бұрын

Electric cook tops cycle on and off like that too. It is easy to tell because they are usually red when they are on. We have one of those glass ones and the nice thing is they are easy to clean. Mom accidentally melted plastic onto it (not a lot of plastic) and once it cooled down it was easy to scrape it off with a razor blade. Once I got it clean enough I turned it on and there was no burning plastic. That just proved how well the razor blade worked. If that was any other type of cook top it would have been much more difficult to clean up. I think what made that easy to clean up is that she caught it before it could burn.

@Inventor101 5 жыл бұрын

Wow what a fantastic idea I love this channel😀👏

@Inventor101 5 жыл бұрын

David Westernall probably first time I’ve seen it done this way

@Wilson84KS 5 жыл бұрын

Which idea? I don't get it, I see only some adverts in one video and a someone winks with a pcb sometimes between the adverts

@taqihaider2173 3 жыл бұрын

Is it you

@sangitadixit9796 3 жыл бұрын

U have a yt channel I have subscribed it

@user-ub2ib7cw2u 3 жыл бұрын

Big fan inventor 101

@AsitShouldBe 3 жыл бұрын

i've just bought my first yacht using your credit card number, thanks friend!

@Bxlxji18 5 жыл бұрын

Seriously, i tried to make an own Iron Solder many times but it failed this method is very simple I LOVE THIS CHANNEL

@chemicstry 5 жыл бұрын

Ideally you should spread all solder paste in one pass. Smearing stencil multiple times causes paste to squeeze under the stencil and causes problems with fine pitched components.

@mikin.6595 5 жыл бұрын

Thank you for shearing!For many years in electronics this video was very refreshing for me.Thank you again.

@burhaelmusic 5 жыл бұрын

We have already used it for making coffee from Turkey. Logical idea 👍🏼

@ratskirobo4836 4 жыл бұрын

Sand soldered SMD components in non stick pan!!!! My favorite!!!! Yum yum!!!!

@AgentPothead 5 жыл бұрын

I gotta give this a try, thanks for the video. I would agree with other commenters that turning off the induction oven before putting the pcb on is the best practice.

@gapguy9564 2 жыл бұрын

How was yur experience?

@TheGrrson 5 жыл бұрын

Great tip. If I ever make a custom PCB, I'm trying this method.

@prashantpanchal8658 5 жыл бұрын

Wow!! , Nice trick Thanks for trick of soldering😇😇

@konnoriximus 5 жыл бұрын

Amazing idea! How easy... I can't believe it :-D I'll try it out soon, definitely!

@MatSmithLondon 5 жыл бұрын

Fantastic idea. Nice job. Results look good.

@narendravadiya7219 5 жыл бұрын

Great.New idea,I have never seen.let me try it. Your demonstration is good.Your voice is also crystal clear. Thank you. N.M. Vadiya Mahuva, Gujrat. India.

@karthickvaradharajan 5 жыл бұрын

I didnt except this very useful method Thank u for upload this

@S_U_R_A_J 5 жыл бұрын

Your grammar is killing me though.

@plac-horizon0043 5 жыл бұрын

Thank you so much BROTHER it helped me a lot

@shibnathshaw5666 5 жыл бұрын

It is great idea, whole world apricated this as 'Jugar ka Idea '. I think we Indian play One's Cards Well. Thanks for sharing, have a good time.

@helltanner3722 5 жыл бұрын

i was going to call BS on this then watched the video....good idea good info good camera work good advice THANKS.

@netrapatil2169 5 жыл бұрын

bro today i desolderedold pcb by tjis method.. worked like a charm

@siliconhub6492 5 жыл бұрын

Thanks for making video sir

@chinmoytahbildar3278 5 жыл бұрын

Thats a brilliant idea... I will definitly try

@rockytechmax2578 3 жыл бұрын

Muze yahi chaiye tha mai bachpan se iski talash mai tha thank you🔥👍🙏

@dineshdeuri7174 5 жыл бұрын

Soldering ides is very important.🙏🙏🙏🙏

@SupremeRepairs 3 жыл бұрын

ಅದ್ಭುತವಾದ ಸುಂದರವಾದ ವಿಡಿಯೋ ❤️😍 amazing and beautiful video ❤️🌹

@MrMahaprasad1 5 жыл бұрын

Superb technique

@sudhap7792 5 жыл бұрын

It's new idea for me... Excited. Its Very useful..

@massilamany 5 жыл бұрын

Wow ! Simply excellent. You can use also salt.

@mohshinkhan9571 3 жыл бұрын

Great solution sir

@toshan5555 5 жыл бұрын

i am watching your videos from past 3 days....your awesome creativity make me inspire....which was mind blowing... i am sure that further you reach 10M subscribers easily..

@doubleHLabs 3 жыл бұрын

I'll have to try this.

@curiousworld6644 2 жыл бұрын

Thanks for sharing precious knowldge

@parth_1569 5 жыл бұрын

Great idea for those who don't know how to solder such tiny components. Thanks!

@laconcongrelos4545 5 жыл бұрын

If you consider that tiny... try soldering 0201 components by hand.

@RedScorpionSL 5 жыл бұрын

I just found this channel. I love this. Maybe you can do a video on making SMART BULBS

@alcoholisfreedrink 3 жыл бұрын

wow. I couldn't even think of that. I have been using soldering iron and tweezers

@redcrafttech2327 5 жыл бұрын

Wow awesome and time saving

@snellface 5 жыл бұрын

10/10 the most swag segue into the square space commercial :D

@ZALDYTV 5 жыл бұрын

Nice video 👍 must share 👍

@shortherogamer9420 5 жыл бұрын

Man your a real talent

@jonmoore1614 5 жыл бұрын

SUper high quality video, I subbed

@simonbecker748 4 жыл бұрын

Brilliant method. Thanks for teaching us

@Aerospaceman 5 жыл бұрын

Like the idea of the soldering template and the idea of using sand with an induction heat plate is very interesting. Great video. USA Washington State Spokane Valley.

@techno1297 5 жыл бұрын

Bro you are genius

@marcelloo.anselmorodrigues2925 5 жыл бұрын

Hi. Great ideia and thanks for sharing with us. God bless you bro!!!

@ratikantprabhakar3875 5 жыл бұрын

A very convenient method for soldering.. great idea..

@PRROBOTICS 3 жыл бұрын

This is really useful 😇

@fawazmulla9480 5 жыл бұрын

Fantastic idea man

@phantomcruizer 5 жыл бұрын

Excellent video! Thanks for posting.

@MKDas 3 жыл бұрын

Useful technique.

@rajasekharreddy5538 5 жыл бұрын

very good video for electronics lovers

@thebraveheartop4142 5 жыл бұрын

Im addicted to ur channel n ur creations😍

@j4techmediajishnusreedharst 4 жыл бұрын

Super never see before like this idea thanks for new idea

@CrusadeVoyager 4 жыл бұрын

Nice technique

@vigroagroresearch1003 3 жыл бұрын

You provide very good information

@harviecz 5 жыл бұрын

Combining induction stove and electronics is not a good idea... Currents can induce in your circuits and fry your components.

@Gumeb 5 жыл бұрын

Maybe,..... Or Maybe the pan absorbs all the induction

@harviecz 5 жыл бұрын

@@Gumeb quite possibly. But are you gonna take chances with expensive ICs or PCB that takes days to weeks to ship if you fry it?

@Gumeb 5 жыл бұрын

@@harviecz you are right, At the moment I would not use the method indicated in the video, at least not until checking with a magnetic field meter that on the surface is free of induction

@toahero5925 5 жыл бұрын

What if you used a conductive pan, then covered it with a metal lid or aluminum foil? I'm far from an expert, but wouldn't that create a faraday cage to protect the pcb?

@PixlRainbow 5 жыл бұрын

Just turn off the induction heater before placing the PCB. The sand will retain heat for quite a long time, longer if you cover the unused parts of the sand surface with some insulation

@jhmusavi 5 жыл бұрын

Wow, what a idea sir

@bouhannacheabdallah 5 жыл бұрын

very nice idea ,keep it up man

@sagarnanaware3463 5 жыл бұрын

What an idea. Very impressed

@EasyOne 5 жыл бұрын

Nicely done

@AGTXX33 3 жыл бұрын

Now i know that how a laptop's motherboard is made of.... awesome video.. 👍

@minkorrh 4 жыл бұрын

Awesome diy technique!

@certified-forklifter 5 жыл бұрын

fantastic introduction! thanks for sharing :)

@yashwanthduke4719 5 жыл бұрын

Make a vidio off realistic mini power banker📲😀😀?

@YAHI_33 5 жыл бұрын

Super and very useful method

@butstough 5 жыл бұрын

excellent video btw. i'm going to try this on a gpu reflow

@dave_dennis 5 жыл бұрын

I have never seen this technique. I will have to try it.

@gnanarajan182 5 жыл бұрын

What an amazing idea it works

@sankhasubhrahaldar380 4 жыл бұрын

Most Satisfying video i have ever seen🤤🤤🤤❤️❤️❤️

@amritachandra9796 5 жыл бұрын

I love your videos, I try making stuff from your videos but I am not good at soldering. Though you are the best! Waiting for next video

@A3Kr0n 5 жыл бұрын

I'll keep putting them on by hand. Thanks.

@longboarderebright 3 жыл бұрын

whattt its so simple yet so perfect!

@squidwardgurun8678 3 жыл бұрын

Out of the box 👏👏👏👏

@fzigunov 5 жыл бұрын

That was quite timely =] will use right now hahahah

@pradipkumarnirjhardas9588 3 жыл бұрын

This is really a good video and very usefull too

@cyberdude6200 4 жыл бұрын

Thanks DDELECTRO TECH

@sajanmistry8800 5 жыл бұрын

Great video! Never thought of that

@robinedores4756 3 жыл бұрын

Very nice project.

@cosmos9227 4 жыл бұрын

Good Idea MAN 👍👏

@MrCreativeBOYBD 5 жыл бұрын

Good work 👍👍👍

@nomer63078 3 жыл бұрын

For me this is the clean type solder for surface mounted device and safe for small components

@ANKITSHARMA-mq5jy 5 жыл бұрын

very nice work sir good job

@barasatravis4836 2 жыл бұрын

Nice work

@RoyTecTips 5 жыл бұрын

awesome idea

@greenway756 4 жыл бұрын

wow good idea thanks mastar

@saimsirswal7434 5 жыл бұрын

Thank you to make this video

@pradumanghosh2422 4 жыл бұрын

Amazing bro 👌🙌

@KuljeetSingh-yk2hn 5 жыл бұрын

You are just amazing man

@padmalayarawal3091 5 жыл бұрын

Super awesome idea.......👌

@kshitijtechnicals2609 3 жыл бұрын

Very good idea

@izhal75 3 жыл бұрын

Thank you sir.

@arjunjs8075 5 жыл бұрын

You are impressing us again 😍

@disware2844 5 жыл бұрын

Nobody: DD electrotech: PCB BOARD

@papadenj8262 5 жыл бұрын

PCB way

@redakaminekloc5167 4 жыл бұрын

Printed circuit board board

@yaswanthfinds 5 жыл бұрын

super idea.....!number 1idea

@ganeshk2607 3 жыл бұрын

Wow awesome idea

@ARKCRAFTZONE 3 жыл бұрын

Thanks

@secureitmania 5 жыл бұрын

Thank you

@prajwalkoppad2958 5 жыл бұрын

Its very easy Wow!