I’ve been running a homemade tubeless sealant in mountain bikes and dirt bikes for years - 1 part mold builder liquid latex, 1 part ATV Slime with the rubber chucks to stop up holes, 1 part pink anti freeze to keep from evaporating in the tire, 2 parts distilled water. I remove the valve core and squirt it into an installed tire with Stans injector tool - works great, a little thicker than Stans but holds up better in my experience to punctures.

This video really help my confident to install the tubliss system in my dirt bike..

Really enjoy your videos! Keep the good content coming!

Great arm workout putting on those tires!! Great tutorial.

Great install video. Does not look as bad as I thought it would be.

donnie this is your niche. you can blow up as a youtuber if you keep making tutorials. the editing and content is 100% spot on perfect. camera angles, lighting, all of that, great job !

You have the nicest shopfloor I’ve ever seen

I know I'm not the first...but THANK YOU for the slow detailed instructions / video! Just installed my first tubliss rear...AT81EX used Stans...had to finaggle one spot where the bead didn't fully seat...but after inflating both air chambers it seated! Only drew blood once on a knuckle! And no cursing!

Nice install. Yea I had to put some sealant in my front tire for some reason.

Good to know I'm not the only one with tire irons flying around the garage lol!

nice..... good tutorial

I’ve used Stan’s and Trucker cream sealants for years on MTB, road bikes and motorcycle tubes and tubliss. Suggest to avoid the sticky mess, and mention the cost of the expensive cream lost, to use a syringe to pump the cream in the low pressure valve stem AFTER the tire is installed. Also, you need to add more cream around every few months to avoid latex holes from dried up sealant.

I gave up on tubliss because of the slow leaks on the low pressure side and getting a nail through the high pressure tube once. This stans sealant may be the solution. I have been running the mousse’s and really like the peace of mind of never getting a flat no matter what and never having to check the air pressure.

Great video thank you. I'd make similar videos of me fitting tyres but there'd be so much swearing it'd be R rated!

You need to ride at highland park in cedar town Georgia it’s on the boarder of Alabama and Georgia they could good trails and lots of single track and some good Mx tracks lots of clay tho gets slick when wet,they also have some really nasty hard trails great atmosphere tho nice people they do get angry if you speed threw the main gravel road tho.

I did it EXACTLY like you did, using the same sealant. It’s leaking on the low pressure side really bad. 😞 It was my first tire ever.

how does Stans compare to Slime? I've used slime before with Tubliss but it tends to be really thick.

I'd suggest airing up your high pressure tube after installing it to the wheel to ensure it is holding air and not damaged from mounting, before you art mounting the tire

Solid video...thank you for making it...I've been running Nitro Mousse for a year now...before that I ran Tubliss...wanted to see what all the hype was about...obviously Mousse has piece of mind with zero flats, however, I have found that the Mousses really hurt suspension performance, are much heavier and make the bike sluggish, and you just don't get any feel from them...so I'm going back to Tubliss. I used soapy water before and did have some leak issues so definitely trying the tire sealant trick this time around. Any reason why you used Stan's VS Slime?

Nice video Donnie. I have been thinking about trying some of that Stan's tire sealant in my tubeless but I haven't heard of anyone using it. Let me know how it does

Do you purchase the tire sealant online or does some places like Walmart or Oreillys carry it?

Great stuff as usual! My question is why not just pour the stans through the valve stem with the core removed? I think id have most of the sealant on the floor before the tire was seated haha

I wonder if a new pull off tire would seal using this method. I have a new bike and want to install tubliss. I would like to pull off the new tire install tubliss then re-install the new tire. Any experience or success doing this?

Noticed you installed the high pressure retainer nut on the outside Tubliss calls for it on the INSIDE. I made the same mistake, just wondering if it really matters? Or do I need to remove and reinstall it like the instructions show? The soft washer is still on the inside. Thx for any and all advice

Any problems with tire removal with Stan's? It might make a good video.

Are you still using Tubliss or have you moved on to a mousse?

Do you have a insta gram

Good video. . .but man, what a messy pita.

pretty useless mess with stans. you dont need that sticky journey. tubliss only is fine. especially on new tires.