Delonghi Dedica EC685 Simple steam wand modification.

No video

Delonghi Dedica EC685 Simple steam wand modification.

Рет қаралды 11,407

Creative Mario

Күн бұрын

easy way of changing steam wand with out takin every part from machine. just open the top and get access. good luck

Пікірлер: 41

@adr3psch624 2 жыл бұрын

Absolutely amazing, no need to tear everything apart. I've just finished my modification now. The advise to put flexi and clamp before saves even more time. Thank you very much!

@creativemario101 2 жыл бұрын

I am happy to hear that. Well done. Thanks you. Regards

@creativemario101 2 жыл бұрын

If you really appreciate it - please subscribe. Maybe more interesting thinks will come up. 😉

@alexanderb4320 2 ай бұрын

Спасибо большое!👍 Купил такой же, подумал что мне не тот капучинатор прислали, а оказывается нужно пропихивать! Всех благ!😀

@Петрович0482 18 күн бұрын

Подскажите пожалуйста, есть разница, стоит покупать? Или с обычным пойдёт?

@alexanderb4320 16 күн бұрын

@@Петрович0482 честно говоря - нет. Ожидал большего. Мыть проще только.

@alexanderb4320 16 күн бұрын

@@Петрович0482 но если надумаете покупать, то чтобы проще пропихнуть, нужно нагреть в горячей воде, и а перчатках пропихнуть будет гораздо проще.

@MToTheFrame Жыл бұрын

Worked a treat, very very easy. For all, try to lever the new wand when trying to pass through the angles (eg put pressure to force the angle at the back). This video saves a lot of time to the traditional method for replacement.

@creativemario101 Жыл бұрын

Thanks

@maxxsee 2 жыл бұрын

amazing find!!! might actually go ahead with this now, because the whole enourmous process was holding me back, thanks man and God bless

@creativemario101 2 жыл бұрын

I am glad that is easier then you think. From the little experience I got l advise to put the flexi and clamp it before you push it down. I didn't and l was struggling a little. So put flexi on as l say. Follow this advice and the movie and will be easier for you then for me. Hot water will help on every plastic part to bend more. All the best. Regards

@seanl8400 2 жыл бұрын

Thanks so much for your guide! Definitely waaaaayyyy easier than the complete tear down from the other videos! 1. For me, i spend the most time trying to remove the rubber tube. I was concerned if the tube will get deformed. In the end, just pull it really hard and it finally came off. 2. Dish washing liquid helps with inserting the new wand. got todo some twist and turns. I did not need to remove the lower section to install the wand. 3. Maybe you or somebody can update the video to show how long should the tube go onto the wand and where should the clip go onto. Although i did got the tube onto the wand, i am still worried if the tube might come off eventually and cause a water mess in the machine. Thank you so much once again!

@creativemario101 2 жыл бұрын

I done the video just to remember how to put it all back . 😁 Then l noticed the easier way. That's why l put on KZfaq. Maybe is available small clip to be more secure, but my still ok . Since you open ones then you know is not that bad. Let me know how you getting now with your coffee.

@mati4400 2 жыл бұрын

Dzięki za filmik miałem wyjmować całą kasetę ze środka ale dzięki Tobie widzę że niepotrzebnie, jutro biorę się do wymiany. Pozdrawiam

@SimoFY 10 ай бұрын

Thank you Sir, it really helped me. Ciao

@klfmarcus 2 жыл бұрын

Good job

@timchong6728 Жыл бұрын

tbh how do you remove the rubber piping by just pulling? it seems almost impossible for me, and when I tried heating it up to loosen it, im afraid it will damage the other part of tube as I pull on it

@creativemario101 Жыл бұрын

Which one ? Tell me the exact time . Minutes and seconds. I will tell you then

@exxxistent830 Жыл бұрын

yeah very simple...

@happy-ge1qk 2 жыл бұрын

dzieki, pomoglo!

@creativemario101 2 жыл бұрын

Cieszę się bardzo I pozdrawiam serdecznie 🌹

@BruceLee_PL 9 ай бұрын

Do kompletu kup sobie kolbę bez dna a będziesz jeszcze bardziej zadowolony z espresso

@ewaewatoja.7804 2 жыл бұрын

Mario, Ciebie to do nagrody Nobla zgłoszę, tylko w jakiej dziedzinie bo jestes jakby w kilku dobry😀😃💪💪💪

@creativemario101 2 жыл бұрын

Cześć Ewa. Sam oglądałem YT jak gościu zmieniał ale wszysko wyciągnął . Tak że pomyślałem że jak mi się tak samo uda , to już będzie dobrze i nic by nie było do nagrania, bo nie lubię kopiować . Jedynie po to aby potem poskręcać. Ale zauważyłem że jest możliwość bez rozkręcania całej maszynki no i pytanie było: czy ten gość o tym pomyślał i naprawdę się nie da , czy też nie . No i był moment że już myślałem że bez rozkręcana dalej ani rusz. No ale się udało. Niech ludzie mają mniej roboty. Dzięki za komentarz ale do Nobla to idą wybitni , a ja jestem zwykły przeciętniak, taki trochę kreatywny. Pozdrawiam serdecznie 💞 Serducho za to , że jesteś 😉

@ewaewatoja.7804 2 жыл бұрын

@@creativemario101 skromność cechą Wielkich...działaj dalej,a może stworzysz orginal warty Nobla.Pozdrawiam i życzę owocnych pomysłów.

@maxxsee 2 жыл бұрын

what about the hot water?? we put the hose into hot water?

@creativemario101 2 жыл бұрын

Boil water helps to make the hose softer and more flexible so is easier to push on the metal element ( just the end ). If is still hard - bit of cleaning liquid make more slippery. Good luck.

@DM-pm2yd 2 жыл бұрын

Please can you post a link to purchase the wand? Was it from Amazon??

@creativemario101 2 жыл бұрын

www.ebay.co.uk/itm/Rancilio-Silvia-AUDREY-BETSY-FANTASY-NANCY-Gaggia-Classic-Steam-Wand-Tube-/115048009791?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=710-127635-2958-0 It is working until now but the chrome is not so shiny. If l buy again l will choose another one. Probably with 2 screws. One with single hole and one with double hole . ( if you do coffee for all family at ones you can heat faster . ) With single hole l got more control . Are you from UK ?

@imagineengine Жыл бұрын

at 12:50 in the video, looks like you forgot to replace c-clip on the white plastic fitting yes?

@imagineengine Жыл бұрын

@@creativemario101 I see the hose clamp, but still do not see the round flat washer looking type clip that has one side cut away. It is shown around the 2:04 point.

@creativemario101 Жыл бұрын

I see your point 👉. I didn't put it back because is not needed there. Slow down to 0.25 and look 1:58 , zoom it , to see where is the washer on the tube. Then go to 3:19 to see the new part. The new part got already ring , no space or chance to put the c clip. That is why new part is fitting from the top and the existing ring on that part do the job as C ring or clip. Old part is fitting from the bottom so C clip is needed. So we not using C clip at all when we fitting this new part. Is probably good to keep it just in case . Do you see the difference ?

@imagineengine Жыл бұрын

@@creativemario101 ah haa. Yes I do see it. I kinda assumed maybe you just didn't need it for the new part. Very nice video. I did find this part after doing a search that your video made me think of and I think I will be installing this part instead. Its also stainless steel, less expensive, and alot easier to install and hopefully serves the exact same purpose.

@MToTheFrame Жыл бұрын

I used the c clip by opening it a little bit and putting on the outer at the bottom to hold it in place and stop it moving up and down, works a treat