Hello Everyone, also see the previous video here: kzfaq.info/get/bejne/lbmSesx1mbLJc5c.html

More than 7300 coffees made on my 5500 - Changed the carafe, door assembly as it was broken and a few other parts I guess it's time for this one! Cheers.

I appreciate the time you have taken to put this together and hope it helps lots of 5600 owners out there. I have replaced all of the ‘O’ rings on the esport prior to finding your clip on KZfaq, to no avail. Milk still spluttered when attempting to make a chino. I followed your suggestion to replace the spout assembly and had high hopes that my coffee machine would return to bring a useful household appliance. Unfortunately not the case. There was little difference with my machine between the old spout and new spout. Working on the premise, that one piece of plastic is as likely to fail as the next one, after replacing the spout I ordered a new milk jug. Once again I was looking for a machine that could froth milk without all the spluttering. This was not to be. It still splutters on the first mug-a-chino, however, almost works when the ‘milk’ option is taken to complete the chino. The next chino works quite well. When a few hours pass and another chino is wanted, the same ritual is needed to be adhered to. I noticed that the lid assembly, on the new milk jug, is extremely loose on the jug. This creates another issue of the jug not being recognised as inserted into the machine, from time to time. Only way out of all of this is to revert to my POD machine, which was purchased as a temp replacement for the ESAM5600, or buy a new coffee machine with a steam spout, allowing manual frothing. Again, thanks for your efforts.

thx... My ESAM 5500 works now fine :) Thx so much from Sweden.

Thank you for doing these how to videos. I have a ESAM5500 with the same issue. I took the o rings off to measure them to see if I had any others lying around to play with. When I was trying to get them off I touched the switch (machine was unplugged) and I think I have done something wrong. If I try to get either milk or water with the carafe or spout in place, the screen briefly says "Heating" then just as quickly returns to "Ready". I have ordered a replacement switch and a replacement coupling. Is it possible I just broke the switch or does it sound more sinister? I don't want to throw good money after bad. I can't imagine the steam leaking between the carafe and coupling would be any good to the switch either.

Cheers for this video works better than new

I have the 4.350.S and today it's decided to stop outputting milk. Worked fine only 2 days ago! Hoping it's as "easy" to take apart, trying to decide on just replacing the O rings or the whole milk coupling. Any recommendations?

Tried this and problem remains. Needs to be used once or twice before it starts working correctly. I read some other comments about a small black o-ring, my spare part didnt come with this. So I transferred the black o-ring from the old part to the new and now it seals correctly and works perfectly. Hope this is useful to others, the small black o-ring sits on the white tube, just before the brass section, to ensure a good seal between the tube and the black milk tube part which is what is replaced in the video

Have you done this on the Eletta?

First, I appreciate the video and the link to the part. But do you happen to know the actual DeLonghi part number? Thanks!

My machine produces good milk foam but it’s not heating it. Do you have a solution for this?

That`s all is nice, however, to replace silicone o-rings can help in the most cases. Much cheaper and effective! Secondly. I`m sorry, but the milk jug selector has to be set up to cappuccino, but on your video it`s on flat white position. Thank you

Thanks for your video. My delonghi will let me Descale, but stopped passing milk. I thought it might be the pump but descale uses the same pump I believe. I also totally cleaned and lubed the carafe seals too,as well as the part you suggested. Also, do you have a guide for the LCD repair? My esam6700 lcd is flaking out

My problem is that my machine won’t stay on milk when I press the button. It keeps reverting to the escape position and wants to clean the spout. Any suggestions?

Question (great vid BTW v useful) have you found that the hot water feature fails? I have this very machine, no milk issues, just when you select hot water it cleans, no hot water at all.

This spare part just a plastic pipe with few O rings. What is the problem on the old spare part? What is the difference? I don't understand why need buy a new one.

Добрый день, кофемашина 5600 кофе работает отлично, но горячую воду не выдаёт ,при подключении молочника тоже не работает. Кофе гарячее , подогрев чашек работает, в чём может быть проблема?

Hey I saw your previous videos on unlocking phone do you have any new trick I have a redmi mobile I M not sure it has debugging on or off and I want to remove the password I forgot ? Please help if you know somone who can do it I am ready to pay anything .

Is there a tiny silicone ring that goes on the white little tube just before fitting it with the new water spout?

Just clean the selection button ( the thin slit above the notch )of the cremá system with a small screwdriver

Hi does this part fit an ESAM 5500 ?

Where do you get the part from?

Thanks for sharing this video. My delonghi won’t pump at all when I press the milk button, although the carafe is registered when I put it in with a faint beep. What else might it be?