design and assembly of bevel gear in solidworks with the help of toolbox

design and assembly of bevel gear in solidworks with the help of toolbox | solidworks tutorial

Рет қаралды 35,791

Күн бұрын

In this tutorial we will learn the design and assembly of the bevel gear in SOLIDWORKS with the help of toolbox, and we will cover material selection for bevel gear. along with that, we will see how to make motion study animation in SOILDWORKS.
what will you learn in this tutorial:
0:00 - intro
0:24 - design of bevel gear
5:52- how to use mate tool
8:54- detect collision of gear with the help of physical dynamics.
9:27- material selection for bevel gear
10:15- motion study animation
watch other tutorials on gears:
design of spur gear: • design of spur gear in...
design of helical gear: • design of helical gear...
design of bevel gear: • design of bevel gear i...
assembly of spur gear: • design and assembly of...
assembly of helical gear : • design and assembly of...
assembly of internal gear: • design and assembly of...
assembly of rack and pinion: • design and assembly of...
design of miter gear: • how to make miter gear...
*************************************************
PC AND SYSTEM I USE
Ultrawide monitor: amzn.to/380s5li
SSD: amzn.to/37YCsGl
Ram: amzn.to/37YyUny
Motherboard: amzn.to/3mGFCTn
keyboard and mouse: amzn.to/34Nt5HM
GPU: amzn.to/3800HUM
PSU: amzn.to/2GkeWZ6
CPU: RYZEN 5 1400
MIC: amzn.to/3kUkPLD
*************************************************
#CADCAMMentor #solidworks #bevelgear #assemblyofbevelgear #solidworkstutorial #solidworkstoolbox

Пікірлер: 21

@TheYapablo 2 жыл бұрын

Thank you so much! With your video I was able to draw the bevel gears which I going to buy based on the sizes provided in the aliexpress site and it is works!

@thstudio7712 Жыл бұрын

Good video, thank you so much

@fulv_uk Жыл бұрын

Very good video thank you. Would you be able to do one for designing gears for 3d printing ? Including clearances? Thanks again

@Arbattachment 3 ай бұрын

very useful video good

@07mayureshtandale56 Жыл бұрын

thank you sir for making this video this will help me out ... i have some doubt about one problem sir its been little bit difficult me for finding their parameters 1.Design and model a Geartrain with following constraints: ●Driven and Driving shafts axes are perpendicular to each other. ●90 RPM is needed at the output shaft if the actuating motor is rotating 3/4th revolution per second. ●Module = 2 , pressure angle = 20 degree. ●No. of teeth on driven gear is 25. Show calculation how you got design parameters of gear. Create an assembly in solidworks, showing a working model of your design with proper mate and no interference.

@rashmidhanawade8981 3 жыл бұрын

Very useful video..

@cadcammentor5867 3 жыл бұрын

Thanks a lot

@Rezakabiri-vh4hm 3 ай бұрын

Tnx

@sheg-lel-loaelmeg-lel-loa3827 Жыл бұрын

thank you for you effort. But go to solidworks tutorial channel and learn the correct way. in reality u dont have sketches to show

@shehbaazsheikh1146 3 жыл бұрын

Can I import this on ANSYS and do the analysis?

@VJ_You_Tuber Жыл бұрын

How do draw sketch..? You didn't show that?

@briantr7 2 жыл бұрын

hii,. what is module in bevelgear? i mean, what dimension is it? thanks

@fatalfire4248 4 ай бұрын

איזה אח!!!!!!!

@DheerajKumar-sv3kc Жыл бұрын

I want to attach a disk and want it to rotate it with pinion but its not happening. Actually i made a mechanical counter and want to attach that assembly at the side of this pinion, but counter's disk is not rotating with the pinion. Although pinion and gear were rotating. Can you help me with this one, please.

@user-sg9gj2jb6p 6 ай бұрын

When I drag and drop the gear into the workspace, it doesn't open the "Configure component" menu that comes up for you, so I can't edit the module and number of teeth. Do you know why this might be happening?