Deye inverter is one of the best inverters in the world at present. We are very lucky to be a partner of deye

Is it possible to connect existing microinverters from other manufacturers to the GEN port via AC coupling (Hoymiles)?

Nice video! My question: Is it possible to use a 1-phase generator or 1-phase microinverter to feed the generator port in the 12kW Deye 3-phase hybrid inverter (SUN-12K-SG04LP3)?

Good clip but I didnt understand one point: If there is a grid failure, will the microinvertre still provide load to the batteries and to the backup loads?

I have 2 X 5KW inverters operating in parallel. The installation is in the Philippines and is prone to power outages due to weather etc. We often lose grid power during storms during the rainy season and I have recently connected an 8KW single phase generator to the generator inputs of both inverters. During recent power outages the generator was able to maintain battery charge which enabled us to maintain power for 4 days. My question is this. Is it possible for the Inverter to operate safely when connected to grid power and generator power? Sometimes during storms we may have intermittent power outages of anywhere from 30 minutes to 2 hours. If this happens during the night it makes for a very sleepless night. We know when the power will be affected and so would it be possible to run the generator connected to the inverters, the ideas being that during power failure the generator will maintain the supply, once power is restored the grid will take over and the generator will remain running on standby. Normally with a 3 phase system we would have synchronizing in place to deal with this. Do these single phase inverters have a system to run parallel with grid single phase voltage? Is this what is meant by the "AC Couple"?

I have 3 invertors at 1 phase. Must i connected gen ports of all invertors at paralels? If my invertors 5 kw each means i can connected my on- gried invertors with power up to 15 kwts

Will this double the export power of the inverter like if I have 5Kw Deye Hybrid inverter ac coupled thru Gen with a 5Kw Inverter will this achieve a 10kw export production on peak power?

Deye seems to be wery good sollution. I plan 4,5 Kwp FVE connected to the grid. In our country is crucial that there is absolutely 0 overlow from solar to the grid. Can Deye invertor guarantee this? Or sollution? Thanks

I have a Deye 6kW inverter and a SolarEgde HDWave grid-tie inverter (3,6kW). Is it needed to set someting in the Solaredge, if I wanted to use it as a microinverter seen in this video?

I have a doubt. I have microinverters and I want to mount a battery, but a can´t put any solar panels in my roof. I see in video that if i connect my Microinverters to Deye GEN input. if there is sun and the battery is 100% charged, the micro inverters stop, and my house consumes battery and not microinverters. I'm right?

Can I use the microinverter feature even there is no battery connected?

can the deye hybrid inverter combine the supply from the solar panel and the grid if the supply from the solar panel is less than the load requirement?

Hi, I've EMPHASE IQ7+ and since i installed the deye, there is more communication with emphase metered gateway. Communication is CPL. Is there any special settings to set for emphase microinverter in the deye ?

Hello, sorry to disturb you, but I need an opinion that no one can give me. I have a deye hybrid 8k lp1eu, with 10400wc of panels. I wanted to put on the gen port, in (ac coupling) 6000wc in micro inverter. Is that possible ? Thank you for your reply.

The new firmware shows ac couple grid and ac couple load , can you pls explain how to use it

Is it possible to use micro inverters as ac coupling when the hybrid inverter is used as island mode ( off grid)

Hi, I follow your channel from Italy and I want to compliment you on your seriousness and professionalism, I admire you, I followed your video on Deye inverters in parallel, I would like to ask you a question, I have installed two Deye inverters and I ask you if the must the circuit breaker that connects the load home be upgraded to 95 A to withstand the voltage changes of two 6Kw Deye or is a 35 A circuit breaker sufficient? Why does my 25A always blow 😓😪

Can we use smart meter instead of CT in a single hybrid inverter setup?

Will this be available as firmware update on inverex Nitrox model

What is max micro inverter coupling size supported on 5kw inverter

what is maximum power of generator input and micro inverter input for 8kw single phase hybrid?

What is the maximum power input from micro inverter? Is it 2000w?