No video
Did they ACTUALLY Improve it? NEW Kingroon KLP1 230
Рет қаралды 4,449
Күн бұрынI compared the BRAND NEW Kingroon KLP1 230mm 3D printer against the KLP1 210mm printer from last year! Kingroon has been making some great machines lately, and this was a fun video to make comparing the print results and showing that the improvements they've made worked out great!
Some of the links shared in our content may contain affiliate or promotional links where we may recieve compensation through your use of them. Thank you for supporting our content!
Kingroon KLP1 230:
loyal.ms/klp1230
Polymaker Filament (code LMSHOWFIRSTTRY saves 15%):
loyal.ms/polym...
I am incredibly fortunate to have Polymaker as my official sponsor! Using my affiliate link is a fantastic way to help support our content!
loyal.ms/polym...
Did you know that I am LIVE on Twitch 3x a week (Mon/Wed/Fri @ 5PM Pacific) where we nerd and geek out about 3D printing for HOURS! Oh, and we also have sponsored giveaways EVERY SINGLE SHOW! Come by, say hello, we'd love to see you there.
/ loyalmoses
Also, we have one of the ABSOLUTE BEST 3D printing discords that have ever existed! An incredible, thriving and supporting community with weekly contests and giveaways as well as support channels and so much more! I do most of my announcements there as well, so you'll want to join for sure!
loyal.ms/discord
We have the BEST sponsors for our content, take a look at these amazing companied who regularly sponsor our content here on KZfaq and other platforms!
Bambu Lab
loyal.ms/bambu (aff)
Gloop!
loyal.ms/gloop
Micro Swiss
loyal.ms/micro...
Slice Engineering
loyal.ms/slice (aff)
LDO Motors
loyal.ms/LDO
---
#3DPrinting #kingroon #polymaker
@TNX255 3 ай бұрын
A VERY short glance at the new version. You're barely scratching the surface here. There would have been so many things you could have compared between them, at the very least; - Noise levels when printing and when idle - Changes in the toolhead department? - Heatup time of the old bed versus the new one - Do they use the same power supply since the bed is now bigger and more power hungry? - Any updates to the software and/or UI? - Any specific issuesthat were in the first version fixed in this one? etc...
@LoyalMoses 3 ай бұрын
That’s the great thing about KZfaq that I think 3D printing people have lost sight of. Not everything has to be in a single video and has to have all the nerdy geeky stuff. Sometimes I get to do a comparison that was inspired by my audience on our live show, and that’s it, just that and if I feel like coming back to it, I might. 3D printing has expanded out past the nerds and geeks and 99% of users don’t care what power supply is being used or if it takes 93 seconds to heat up or 87.
@WARPAINTandUnicorns 3 ай бұрын
Nice comparison to the updated printer.
@LoyalMoses 3 ай бұрын
Thank you!
@sw0rd968 3 ай бұрын
@@LoyalMoses I’m looking to get my first 3d printer and am looking at the flashforge 5m and the qidi q1 pro as they are similar price also the k1 is almost in my budget. Would you recommend one of those 3 printers or is there another option which is better
@ThisisDD 3 ай бұрын
$395(current price) for this vs an A1 for $399 is a hard sell. This would need to drop to AT LEAST 339 for me to even consider it.
@LoyalMoses 3 ай бұрын
Very different customer base I believe. People looking for an enclosed Klipper machine play has a great option here.
@ThisisDD 3 ай бұрын
@@LoyalMoses perhaps you're right. A1 isn't great for ABS or ASA unless you enclose it somehow. I'd still say it is a tough sell for my uses, but not as bad with that context. I will say if the bed size was on par (256+) that would entirely change my opinion. 🤷🏼♀️
@dmhayes6 3 ай бұрын
He turned it on! Good job :) Another great video, thank you as always!
@LoyalMoses 3 ай бұрын
Hehe!
@Happy3dprinting 3 ай бұрын
Great video as always
@LoyalMoses 3 ай бұрын
THANK YOU!
@kschaffer6978 3 ай бұрын
Good comparison as usual . Like how you showed the difference with temp bump also.
@LoyalMoses 3 ай бұрын
Thanks!
@sliverbaer 3 ай бұрын
How many firmware updates have they done for these? For the kps3 line, they all but abandoned the marlin firmware, which was marlin 1.
@LoyalMoses 3 ай бұрын
I have one on each I haven't done yet. I have the KP3S Pro V2 here as well, not sure if it has an update.
@Natesemipro 3 ай бұрын
Ha! Haven’t finished building the printer….
@LoyalMoses 3 ай бұрын
Why do they need so many screws!?!
@skynlab2478 2 ай бұрын
Cool video , the kingroon is cheap and a very good filament
@LoyalMoses 2 ай бұрын
I think they are fun machines!
@kastatd 2 ай бұрын
It's so disappointing they didn't fix the most annoying issues the 210 version had: the screen should be on the outside, bizarre filament sensor placement, the top lid being too close to toolhead etc. They basically ignored all the feedback and shipped the same thing for the 3rd time under the same exact name (the v1 version had no screen).
@LoyalMoses 2 ай бұрын
The lid being too close is a strange phenomenon that all of these enclosed machines have, even Bambu and Creality are doing it, it's weird. I really wish they'd changed the screen out to a touch screen instead of this silly stylus thing. Finding this stylus drives me nuts!
@petercallison5765 8 күн бұрын
@@LoyalMoses Qidi X-Max 3 is the one headroom.
@DWIT3D 3 ай бұрын
Nice comparison. $50 more for 20mm... that's what, $2.50 per mm... I guess it's not bad LOL. Did anything else change on the printer, or strictly the size? Would be surprised if they didn't do more under the cover things to it. Thanks for all the excellent content Loyal.
@LoyalMoses 3 ай бұрын
The extruder gearing ration changed, which appears to have a significant impact on the print results at speed, but overall, they did great making it a more reliable machine.
@Natesemipro 3 ай бұрын
Why did that actually feel like 20 minutes? 😅
@LoyalMoses 3 ай бұрын
What are you saying?! 😂
@Natesemipro 3 ай бұрын
@@LoyalMoses you said I’ll see you in 20 minutes.. and it felt like 20 minutes later while watching the benchies print…
@LoyalMoses 3 ай бұрын
Hehe
@PeeJay7290 3 ай бұрын
I didn’t recognise you!
@LoyalMoses 3 ай бұрын
It’s my evil twin!
@WARPAINTandUnicorns 3 ай бұрын
@@LoyalMoses Never trust blondes. 🤣
@dmhayes6 3 ай бұрын
Had to bleach out the greys lol
@LoyalMoses 3 ай бұрын
Haha!
@LoyalMoses 3 ай бұрын
I’ve just recently started finding a couple of them in my beard, but it seems my hair would rather just leave my head than change color, at least so far! 😆
@ochrum1168 3 ай бұрын
Hi from discord!
@LoyalMoses 3 ай бұрын
Hey! How are you!?
@ThisisDD 3 ай бұрын
Ack! Get the beard back!
@LoyalMoses 3 ай бұрын
They grow back, it’s what they do.
@TinTalon 3 ай бұрын
That did make for some fun content! Great video.
@LoyalMoses 3 ай бұрын
Thanks 👍
Цифровая фабрика
Рет қаралды 22 М.