*Links to my work* Facebook group: facebook.com/groups/899714240405971/ 3D-print: www.printables.com/@PerMejdal/models Wiki: wiki.permejdal.dk *Affiliate links to products I like and use* Prusa MK4 3D Printer kit: www.prusa3d.com/product/original-prusa-mk4-kit-2/?p2p=%40PerMejdal Backblaze PC backup: secure.backblaze.com/r/00d9on One webshoting: one.me/daaaykco SUNLU filament: www.sunlu.com?sca_ref=6638083.h9MBiFeRw5

I would love such a quality video for every piece of hardware I own.

I was trying to use a CR 2450 battery on the remote control. I followed your other video to open it up but mine turns out to be the newer version 😂 Then I saw this video😄

Could you please show how to put the battery in correctly - what is the right way?

The new remote control uses the same firmware image type (0x11C1) as the old one. Details about the custom remote control: www.thingiverse.com/thing:3655354

great video thx u changed my life

Troubleshooting for the TRÅDFRI remote control Many (everyone) experience problems with battery-powered devices being difficult to connect to the gateway and difficult to update. Failsafe guide for when things have went wrong 0) Place your gateway somewhere where it is comfortable to work with. 1) Clean up. 1.1) Delete all disconnected devices. 1.1.1) Go to Settings> Manage Devices. 1.1.2) Scroll to the bottom. 1.1.3) Delete devices under "disconnected devices". 1.2) Delete all devices with pending update. 1.2.1) Go to Setting> IKEA Home smart version 1.2.2) Note names of devices with "Update pending". 1.2.3) Go to Settings> Manage Devices. 1.2.4) Delete the devices 1.3) Reboot gateway. 1.4) Repeat from 1.1 until there are no devices to delete. 2.) Add deleted devices. 2.1) Insert fresh battery. 2.2) Pair it to the gateway. 2.2.1) Go to Settings> Manage Devices. 2.2.2) Press the plus at the bottom. 2.2.3) Select the device type and follow the instructions. 2.2.4) If pairing fails go to 2.2.1, remember to reset the device. 2.3) Place device next to gateway. 2.4) Wait for update to finish. 2.5) If the device is not updated after one hour, go to 2.1. If the problem persists, go to 1.1. 2.6) Repeat from 2.1 with another device, until all devices are added. Explanation of why steps are necessary 1.1) Pairing a device which is already on gateway as disconnected device will fail. 1.2 + 2.4) Updating multiple devices at the same time can stall, and then block pairing and updating of other devices. 2.1) Low battery power can prevent pairing and updating. 2.2.4) If pairing fails, it is important to restart pairing again on both the gateway and the device.

Thanks!

When I innstalled today phillips hue being lamp with dimmer switch, something has happened with IKEA smart Light in the same room. and now my IKEA remote doesn't work! I tried to reset it, but it did not help! What Shall i do now? 😩

You mentioned the Zigbee module itself is slightly changed, do you know if it still contains EFR32MG1P132F256GM32, or could it have an other version of that chip? It would be really fun if they upgraded to a 512kb flash module so it could be programmed with the zigbee stack by GCC.

I turned the power off at my panel so that I could safely install a new 30 amp breaker. when I restored the power my ikea under cabinet lights were on, and can no longer be controlled with the remote. Put in new batteries and followed the reset instructions by pressing the little button inside. did not work. any helpful suggestions?

I have a single button ikea remote. How can I make the newest trådfri work with it.

Just love your irony… ;-)

Hi, is there a difference in opening the two versions? I tried to open the new one but was not sucessful.

Kan se du bruger knappen til diverse smart pærer i andre videoer. Kan den parres med hue hub og programmeres som man vil deri?