Super Duty E Locker Swap! (Sterling 10.5 / 10.25)
Рет қаралды 3,695
2 ай бұрынToday we take out the garbage limited slip differential that came with the one ton axles I installed in my 2010 Toyota Tacoma, and swap it for a factory Ford E Locker from a 2011+ F350.
These E Lockers can be found cheap at junkyards or in my case Facebook marketplace and will work in any Sterling 10.5 or 10.25 axle.
Snail Armor Panel: snailarmor.com/dirtgarage
Support Dirt Garage by purchasing our Merch! - www.dirtgarage.ca
Brought to you by @ Alpine Toyota - alpinetoyota.com
10% OFF YES WELDERS: yeswelder.com/?ref=z9n5g70h
10% OFF YANKUM ROPES: yankum.com/?afmc=DirtGarage
INSTAGRAM - / dirt_garage
Music Licensed @ Artlist
Find music for your videos on Artlist! artlist.io/Clinton-279876
Business contact: Dirt.Garage@outlook.com
@JW-cn6op 2 ай бұрын
The thick cut gears are made to run on a 3 series carrier so you don't have to replace the carrier when going to lower ratio that would normally use 4 series with a normal gear set.
@abpsd73 2 ай бұрын
That's what I was thinking, a thicker ring instead of having high/low ratio carriers.
@vmoney9106 2 ай бұрын
Never mind the locker, loving the hair!🤟🏼
@Gerry-K 2 ай бұрын
Yeah Joe Dirt, Canadian style!
@caseyh7826 2 ай бұрын
Thats sick, i love cheap performance parts lol. Although it looks like an antiwrap bar would be helpful. Looks like you were getting decent axle wrap.
@DirtGarage 2 ай бұрын
There is a anti wrap there 🤣 But what you can't see is it ripped off the factory crossmember.. Gotta build a solid crossmember for it
@caseyh7826 2 ай бұрын
@@DirtGarage all those toyota horsetorx twisting shafts and ripping brackets 😆
@mountainjeepmike 2 ай бұрын
Nice upgrade!
@travischapin886 2 ай бұрын
I have a 2016 F-250 with the E-Locker, works great.
@monette44 2 ай бұрын
Nice shaft.... a little twist for funzies 😮
@nemesis851_ 2 ай бұрын
Can tell this was a research project, before diving in
@jameshall4385 2 ай бұрын
Your "new" used locker looks like the previous owner didn't install the pinion correctly and it self clearanced on the carrier. You might want to keep an eye on that
@DirtGarage 2 ай бұрын
Yeah it had a crush sleeve failure I was told. I'm well aware of that 🤣
@DNance_1 2 ай бұрын
About to do the same. What gauge wire and thread size for the cable gland did you use?
@nemesis851_ 2 ай бұрын
I wonder if the solder, heatshrink, connector, seal, wire coating is temperature rated to the gear oil temps
@nemesis851_ 2 ай бұрын
I see in the thumbnail solder was external to diff
@tommcl8548 2 ай бұрын
👊👍
@sla052609 2 ай бұрын
How did the pattern turn out ?
@DirtGarage 2 ай бұрын
Pattern was perfect still. Drives better than it did before, being completely open on the street is nice.
@MichaelSchmitz-mk8ll 2 ай бұрын
Ford.....😂 Look up Dodge in the dictionary an tell me what it said.... Lol, Ford in a Yota 😂
@dylanromine4101 2 ай бұрын
Why are you using red rtv?!?!
@DirtGarage 2 ай бұрын
Because it's what I had! It will be fine 🤣 Just not as pretty as black.
Precision Transmission
Рет қаралды 42 М.
Точно Новости
Рет қаралды 1,2 МЛН
МАРТИН БОГАТЫРЕВИЧ garage
Рет қаралды 646 М.
its.maarten
Рет қаралды 11 МЛН
Скорая помощь
Рет қаралды 1,8 МЛН
Truck Drive
Рет қаралды 14 МЛН