You missed the part where you drop a ball bearing and it disappears under the work bench.
@felipeantonio8426Ай бұрын
😂😂😂
@user-ut3jk7it6c4 күн бұрын
clearly he is an amateur
@sergiomengual3 ай бұрын
I usualy dismount the disc brake first. To avoid any possible contamination of the disc with grease.
@pizzapie4me3 ай бұрын
This is the way
@sergiomengual2 ай бұрын
@@pizzapie4me I don't make a living from working as a bicycle mechanic, but when I have free time, I try to do these maintenance myself, and it is better to do them calmly, with time and conscientiously.
@pizzapie4me2 ай бұрын
@@sergiomengual I do wrench on bikes for a living, and the same approach is advisable.
@marcello03315 күн бұрын
Brake cleaner
@user-qe3lf6dn1z21 күн бұрын
Я выбросил насыпную втулку, на ней еще был геморройный центрлок , поставил на промподшипники и ротор на болтиках ,, немного тяжелее , мне рекорды скорости нужны
@shaneapplegate1975Ай бұрын
Sealed bearings and forget that crap ✌️
@mechadrakeАй бұрын
it is sometimes no help, because races are damages and the wheel dos the same indexed thing after :) I just did one wheel like that on my very old bike. i messed it up apparently sometimes more than 20y ago :D
@pdxyyz432726 күн бұрын
It's called brinelling.
@SuperMickey5717 күн бұрын
The only thing I do different is put the tip of the axle in on the first side so the bearings don't fall into the hub.
@doctorowl200423 күн бұрын
В конце крутится колесо и щелкает. Отличная работа. Хотя может это гайка на престо ослабленная. А зачем было менять смазку. Она ж нормальная. Выглядит как литол.
@user-zr8qk2fy2yАй бұрын
Насыпные подшипники - в топку!
@fazedordeviuvas36723 ай бұрын
Manutenção satisfatória!!
@jaredelcapitan7378Ай бұрын
Como se llaman esos productos de bisicleta
@user-ug2ph5re6n2 ай бұрын
Nice job❤❤
@quetorro1Ай бұрын
Как я не люблю эти насыпные подшипники, каждый раз после настройки начинаешь затягивать и настройка сбивается
@gerasimov_mvАй бұрын
Какой настройки?
@neptun939337 күн бұрын
@@gerasimov_mv головного мозга походу
@khiemnguyen43616 күн бұрын
Đúng clip tui cần
@jamesmckenzie3532Ай бұрын
Way too much grease. That's going to become a grit heaven. Enough to coat the balls and no more. There's no need to grease the cones either. And yes, I've done this including replacing worn out cones on Shimano Ultegra wheels.
@mrfrogg46able16 күн бұрын
a phrase, sealed cartridge bearing
@f.f.886911 күн бұрын
This is a shumano hollowtech II , right?
@artegos55517 күн бұрын
😊❤
@Jxrd9918 күн бұрын
What about the other side?
@csawserv21 күн бұрын
What about “Pretension”?
@arsenkaaa24 күн бұрын
Это жойтеч, чел, чё ты хочешь от них
@13-Apr-prizrakАй бұрын
Что делать если стучит в заднем переключателе
@doctorowl200423 күн бұрын
Проверить что там стучит. 😅 Может это подшипники в роликах. Меняй ролики.