To order Grease for servicing the hammer see link below amzn.to/3JzRYdG
@riccardograsselli94656 ай бұрын
I have this hammer, i used it with long drill bits (maybe i stressed it too much) and now when i use the rotary drill function i can see the the tipping point of the drill bits swirling around. What do you think i need to replace, what can be broken? The hammer function works fine, but as a rotary drill (without hammering swtiched on) i can't make precision holes when the tipping point doesn't stay firm on his axis! Thanks you very much in advance for every suggestion and help!
@doctorlefthandthread6 ай бұрын
@@riccardograsselli9465 I think the main tube is bent unfortunately when you buy the parts and fit them it wouldn't be worth doing. I would suggest buying the same model again and keeping the old one for parts or as a back up
@joebeatty81665 ай бұрын
Thank you for your comments and verbal support on every single thing that you did. Especially concerning the sheared crank assembly and proper push back action of piston when the right O-ring was asserted. The replacement items, lubrication links and transcript were also very helpful.
@doctorlefthandthread5 ай бұрын
Thank you for commenting it all helps
@chrisfinn11622 ай бұрын
Thanks very useful information. 👍
@snazy777717 күн бұрын
Just popped back in to let you know your video helped immensely when stripping and rebuilding my hammer drill.
@doctorlefthandthread16 күн бұрын
Thank you these comments all help keep me at these repairs and tutorials
@JohnSmith-ws7fq2 ай бұрын
Cheers! 👍
@doctorlefthandthread2 ай бұрын
Thank you sir
@TacticalThib11 ай бұрын
I really like this one doc!! Very detailed and helpful. I'm fairly confident that I can do this same repair after watching and learning from you!! Thanks again doc!!
@doctorlefthandthread11 ай бұрын
Thank you Branden Hope you are healing well
@bwselectronic11 ай бұрын
It's always good, and doesn't hurt, to replace O rings, rusty nuts & bolts etc.
@doctorlefthandthread11 ай бұрын
That O ring nearly always gives trouble it is usually sensible to replace it when you are in there
@darrenirvine55911 ай бұрын
Great job lad..the only thing I would comment on is when you are prying the hammer tube up and out of the case... Keep your hand away from the back end... I have had ones before that have broke the c clip holding the gear and spring on.. it can come out like a bullet... But that was well done and we'll explained... Take care my friend.
@doctorlefthandthread11 ай бұрын
Good man Darren thank you
@arifqureshi992811 ай бұрын
Great. Very helpful video.
@doctorlefthandthread11 ай бұрын
That was my intention to make a proper helpful video of this model thanks for your comment
@rayw66904 ай бұрын
Very detailed video, thanks Doctor. Just wondering where can I buy a spare 3 pin connector at the bottom of the drill for D25303DH dust extractor? I have checked everywhere but can't find it.
@doctorlefthandthread4 ай бұрын
I can't see a listing for it online
@MAXY123993 ай бұрын
Awesome video can I just use synthetic grease for everything and where would I order new o rings ?
@doctorlefthandthread3 ай бұрын
Use light grease inside the tube in the sliding parts Heavy grease on the cogs Ebay for the o.ring www.ebay.co.uk/itm/386435103102?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ctxmdqtptf-&sssrc=4429486&ssuid=cjPn_ZfdQLW&var=&widget_ver=artemis&media=COPY
@kevinmccartney-cu7cv11 ай бұрын
Good video Paul
@doctorlefthandthread11 ай бұрын
Thanks Kevin it might help some man out
@davelaye70038 ай бұрын
thank you so much
@doctorlefthandthread8 ай бұрын
You are welcome
@konstantine38111 ай бұрын
Got the brushed version so while giving it a clean up i checked an seen someone's been in it and the grease looks green, not sure if it's the right stuff but the machine works fine only problem is hammer drill and hammer mode makes a really loud clacking when you pull the trigger more than half way.
@doctorlefthandthread11 ай бұрын
Is there anything broken in yours the brushed version has the same hammer mechanism?
@konstantine38111 ай бұрын
@@doctorlefthandthread the insides seemed fine, nothing out of place from what i saw, didn't take the hammer assembly apart though so maybe its in there
Where are you based pal do u do repairs I've the same problem
@doctorlefthandthread8 ай бұрын
I am Co Tyrone I do repairs for people that ask I still don't refuse much.
@Surfingaliens6515 күн бұрын
I went over to Dean Doherty's channel, but it has been hacked in the last couple of days. I am repairing a 273 which has a broken crank shaft. I might have a problem fixing it as I don't own a bearing press or puller. Any suggestions? Thanks a Million.
@Surfingaliens6515 күн бұрын
The crank shaft is sold as a single item. Dear enough, at £45
@doctorlefthandthread15 күн бұрын
I have taken bearings off with a claw hammer or pry with strong flat screwdrivers before but you need to be careful easy to damage them that
@doctorlefthandthread15 күн бұрын
It is sometimes I have old ones
@arifqureshi99289 ай бұрын
My dch273 making horrorable knocking sound on hammering, what will be the problem???
@doctorlefthandthread9 ай бұрын
Likely the washer down the tube on the striker number 37 or 41 on the parts diagram that's where the issue is www.partshopdirect.co.uk/dewalt-dch273-rotary-hammer-spare-parts-s15448/
@arifqureshi99286 ай бұрын
Thanks a lot.
@Patmac7411 ай бұрын
A large syringe with a little bit of tube on it would make a handy little grease gun
@doctorlefthandthread11 ай бұрын
Big syringe is good for that job yes
@Patmac7411 ай бұрын
Can you use a beef and tomato pot noodle tub?????
@doctorlefthandthread11 ай бұрын
Absolutely the parts will taste more of beef though but this will not adversely affect the performance of the drill
@Patmac7411 ай бұрын
Beef and tomato would probably be better for milwaukee
@doctorlefthandthread11 ай бұрын
And original curry for a Makita
@Patmac7411 ай бұрын
Koka noodles for parkside 😂😂
@daved628411 ай бұрын
Hi link to parkside repairs as promised kzfaq.info/get/bejne/htR6o66Hr7TMpo0.html