DIY 3D Printed RC AVATAR SCORPION
Рет қаралды 237,795
4 жыл бұрынLink download STL file:
cults3d.com/en/3d-model/game/...
Parts:
Motor (You need 2 motor): sea.banggood.com/custlink/Dm3...
If above motor out of stock. You can find the alternative motor here (choose around 2400KV version):
bit.ly/2D7vSAs
bit.ly/32sW7Ko
bit.ly/2Ezv8or
bit.ly/2YGhyGG
ESC: bit.ly/3gzAsoD
(You need 2 ESC)
Flight Controller: bit.ly/3hCFxOg
Servo: bit.ly/34ySqp4
(You need 2 servo)
Links Servo (1.3mm): bit.ly/3gwjEil
(You need 4 Links servo 1.3mm and 4 steel wire 1mm to connect servo with links servo)
Rx XM+: bit.ly/3hza6Vl
Tx Qx7: bit.ly/32sYGMk
Carbon Tube (OD 8mm. Please note to choose 8mm OD tube): bit.ly/3b6c8tp
Alternative Link: sea.banggood.com/custlink/Dmm...
(You need 2x10cm and 2x18cm of 8mm OD Carbon Tube)
Bearing: bit.ly/2EzW9HX
(You need 4 Bearing)
M2 Screws: bit.ly/2YGkIKy
(You need 16 pcs M2 16mm: 8 pcs to connect Body -1 to Main Body. 8 pcs to connect Body 1 to Main Body | 13 pcs M2 8mm: 5 pcs to connect Body 2 to Body 1. 2 pcs to connect Body -2 to Body -3. 4 pcs to lock servo to Main Body. 2pcs to connect Main Body Cap to Main Body)
M2 Nuts: bit.ly/2YHkqDf
(You need 4 M2 Nuts to hold mainboard plate in Main Body)
M3 Screws: bit.ly/3lyKZnY
(You need 2 pcs M3 16mm to lock 8mm Carbon Tube with Lock Servo and 4 pcs M3 12mm to connect Landing with Body)
M3 Nuts Nylon: bit.ly/2G4oRBB
Propeller: bit.ly/32Agqp0
Battery: bit.ly/3hAppNq
THANKS SO MUCH for your visiting here, if you have any questions, query or anythings just leave your comments or email me, I will try to reach you all.
P/s: If you want to support me more, YOU can do it on patreon or paypal so I have no more difficulty on video budget & expenses making. I am very appreciate it even with small amount it can encourage and help me a lot. Thank you for your considering supporting my work.
My Patreon: / vuikhoahoc
My Paypal: paypal.me/phongpp?locale.x=en_US
@eduardo33 3 жыл бұрын
You are really a very gentle person to give the all directions for build this nice project. Thank you very much!
@14768 3 жыл бұрын
This is one of the most well designed 3d printed things i've ever seen on youtube, nice job. I do have a couple recommendations though. For one, on the tail, you could design it with a recessed and protruding 'spigot' as it were, with a taper, so when you glue it together it registers its self perfectly. Secondly, on your internal webbings with the circular cutouts which print as extreme overhangs and lead to some sagging in the unsupported areas, what I have started doing with those is taken a tangent line from the circle up to the center point at a fixed angle, whatever my printer is capable of printing. So let's say a 55 degree overhang, resulting in a 70 degree included angle at the point on the top. So it's still mostly a circle, just with a pointy hat. It really cleans up the prints. I also do this for screw holes where i'm recessing the head of a socket cap screw in something that will print where that hole is horizontal instead of vertical.
@ObsidianDragonCreations 3 жыл бұрын
This is incredible, was waiting for someone to make one of these for years 😍
@Jean-Raoul 3 жыл бұрын
Perfect control ability, great job with only 2 rotors !
@rnbspowa7of69 3 жыл бұрын
I knew the scorpion tail need to be shorter then the one on the model. Thank you for building one really fly’s.
@IcanCwhatUsay 4 жыл бұрын
This is freaking awesome!
@LeeCruz337 3 жыл бұрын
This is some next level design work truly inspiring
@jappiemoto 3 жыл бұрын
That flies really smooth wow
@lbenigno2473 3 жыл бұрын
Liked! Subscribed! Will try! I am totally new to this but you make it look so easy to follow!
@musca8803 3 жыл бұрын
Really good job! Thanks for sharing.
@angelovideo71 3 жыл бұрын
Very good work! Congrats
@marcelbettignie5638 4 жыл бұрын
Felicitations, you are a good designer (enginneer)
@alifhidayat5458 3 жыл бұрын
You are very clever in designing it very detailed and neat
@Artem-gy3zu 3 жыл бұрын
Превосходно! Потрясающе!!! ))
@Voldemar1006 3 жыл бұрын
Абсолютно согласен
@TytusG 18 күн бұрын
that is a sweet looking empennage
@FjrnVR 4 жыл бұрын
I wonder if you could use drastically different equipment of the Convergence VTOL which already has servo pitch and ditch its rear motor?
@jlai9001 3 жыл бұрын
WOW!! You just proved that either Avatar was just really lucky to happen to get the "would-be physics" correct or they actually got real engineers to consult with the modeling process. I can now rest at ease. Thanks!
@nerys71 3 жыл бұрын
You ever see a V22 Osprey? it actually exists as a working military aircraft.
@jlai9001 3 жыл бұрын
@@nerys71 Yes! Twin engine vtol aircraft. Yet I think the scorpion is too far off in the sci-fi zone that I didn’t think it would function. My guess is that I was thinking more towards a helicopter and it doesn’t have a tail rotor. Still very impressed!
@TheRealKitWalker 2 жыл бұрын
It's so awesome!! 😍👏👏✌️
@fly99hummingbird 4 жыл бұрын
Great educational. Thank you
@makewithmegma 3 жыл бұрын
Amazing work👌 👍
@excellenceinanimation960 2 жыл бұрын
fantastic! Im working on mine but having trouble in betaflight. I need mine to fly like a chinook and not sure how to do that. As well as a problem wit ECS's
@GABRIEL1030 3 жыл бұрын
Great job !
@philipptux4086 3 жыл бұрын
Superbe ! merci de ce partage Superb! thank you for sharing
@maskog 2 жыл бұрын
Hello thank you for this project and I’m really inspired by your work and how you carefully presented it. You have my respect. I have a question for you. Can you recommend an alternate flight controller bcos Banggood doesn’t carry the one you use any longer. Thanks 🙏🏾
@ziedtimoumi9496 6 ай бұрын
Hey, i want made one without using 3d printer, is there any plan for the parts, i want use pvc sheets to build it. Thank you
@hasserecht3678 3 жыл бұрын
Did you print this in PLA? If yes take care of the middle portion. The ESCs will get pretty warm, warm enough that PLA gets bendable again. Either don't use PLA for the middle portion or do some active cooling. And you have many mating surfaces where metal comes in contact with plastic while rotating. You could add washers to prevent rubbing.
@user-zs4iv3vf5m 3 жыл бұрын
nice , could it be the body smaller or the thruster bigger let the scale proportion follow the Avatar movie?
@efraimk1673 4 жыл бұрын
awesome!
@SchaafStyle 2 жыл бұрын
Unfortunately I can't get it to work with a betaflight F3. betaflight does not accept the setting for Bicopter. switches to custom airplane.
@hrushikeshashtekar6294 4 жыл бұрын
What is the weight .. apart from the electronic.. just the 3d printed parts?
@hasjan1 Жыл бұрын
Hello, can you advise us of an alternative to the recommended control board, I can't find it anywhere, thank you for the advice.
@RafaelMartinez-wn9pm 3 жыл бұрын
Hola amigo,tengo una f4 y no soy Capaz de que eche el vuelo,muchas vibraciones y muy agresivo buelca.puedes decirme que PID llevas o alguna alludita.saludos
@tahirusman5929 3 жыл бұрын
Excellent!
@bandteeskinnyjeans 3 жыл бұрын
Amazing!
@mulderx2525 3 жыл бұрын
nasa is searching for new talented people. lead the way.you deserve it.
@sciencefun5059 3 жыл бұрын
hahaha, thank you very much But I think your saying is exaggeration. this is not new idea of 2 motor drone, the model is already show in avatar film. I just copy the idea and 3D modeling it
@user-rg9fo1wn5h 3 жыл бұрын
очень классная работа..))) прям захотелось такой же !!!!👍👍👍👏👏👏👏
@gamingisnotacrime 3 жыл бұрын
у вас есть 3д файл?
3 жыл бұрын
Hello, i like your project, but i have one questoion, Ican use matek F405CTR? why i have this here
@sabinfigaro8272 3 жыл бұрын
Se puede hacer en aluminio...? Y mas grande con motores mas potentes..??
@Idlyresearching 4 жыл бұрын
How haven't you gotten literally all the views?!
@milaanpatel4997 3 жыл бұрын
@10:00 You could have wired through the carbon tube.
@riverisaac456 4 жыл бұрын
Awesome , would you be able to make one that would accommodate 1045 props ? For sale ?
@paulopontes3261 3 жыл бұрын
What settings you use inside flying program?
@blakblak5479 3 жыл бұрын
How many minutes did this drone stay in the air
@Wad3c 3 жыл бұрын
Where did you get those 2 long servo horns?
@goosefpv Жыл бұрын
Have you got any other flight controller alternatives?
@modellbau8648 3 жыл бұрын
А flysky F6 аппаратура подойдёт или надо покупать именно taranis x7???
@heinzbaumann4666 3 жыл бұрын
Hallo, welchen 3D Drucker empfehlt ihr, oder kann man die 3D Druckteile kaufen ??
@-robo- 2 жыл бұрын
Very nice.
@Aliamaengineer 2 жыл бұрын
body50 part is missing in sitl files.help me
@0zdurus Жыл бұрын
Flight control link fail. New flight control, Can you renew the link?
@AltarastLD 3 жыл бұрын
Смотрится круто ))
@lacosadz6519 3 жыл бұрын
Awsome te felicito hermano
@princepaulp973 3 жыл бұрын
Bro can you tell be the model of your radio controller
@marcdunivan2436 11 ай бұрын
I wish someone would have made a more helicopter-like version of this. ( dual fixed, constant-speed rotor with collective and cyclic pitch ). Like the CH-47 Chinook, but sideways. This would allow for autorotation to land and a bigger rotor motor to be mounted in the fuselage.
@dusty4896 3 жыл бұрын
You could make these and sell then for so much money, there is nothing else out there like them!
@mateusblachnik4288 4 жыл бұрын
What for a flight time do you have? Is the copter not to heavy for only 2 little Motors?
@sciencefun5059 4 жыл бұрын
With my parts selection, flight time around 3.5min
@sumanta.2004 4 ай бұрын
Is that a F4 flight controller??
@rafaelmauriciomendez1728 3 жыл бұрын
Hi how are you my friend ? very good design I wanted to ask you if I can acquire the code of both the emitter and the receiver to analyze it and do it directly in c ++ in arduino nano I was looking at the list of components and I wanted to ask if the frsky xm can be replaced by the nfr24L01, I would like to be able to do This project but the costs are very high I live in Colombia and the change from dollars to pesos affects me, on the other hand I really appreciate that you share your knowledge with us in this way people like me can improve .. I would like to acquire the programming codes now I have done some projects in tinkerkard but I need to improve and I have no one to turn to based on your codes, it would be very useful to me THANKS GOOD DAY.
@johndeer4878 4 жыл бұрын
Superb
@RA-je6nz 3 жыл бұрын
awesome
@janbernhard1975 Жыл бұрын
Alternative Flight Controler?
@modellbau8648 3 жыл бұрын
Is the flysky F6 equipment suitable or should you buy the taranis x7 ??
@sciencefun5059 3 жыл бұрын
yes you can use as long as your Rx can connect with FC
@msadikoglu 3 жыл бұрын
DO I USE F3 CARD?
@hnhl.1910 3 жыл бұрын
tổng thiệt hại khoảng bao nhiêu v bạn
@jackdenner4227 4 жыл бұрын
bác ơi cho mình inbox hỏi vài vấn đề với
@gabormihaly667 3 жыл бұрын
How do you know such?
@hohmaster2072 3 жыл бұрын
Интересно, что оно летает-это как со шмелём) Кабеля от двигателей нужно было заложить внутрь карбоновых труб, так бы уменьшили вес модели, не было бы необходимости ставить стяжки,и как по мне много винтовых соединений, которые увеличивают вес модели. А так ,классная штука!
@cheo7811 4 жыл бұрын
How much does it weight with your components including the battery?
@sciencefun5059 4 жыл бұрын
Around 710g take off weight
@wiener35 3 жыл бұрын
Excellent. maybe it's a better idea to reduce its weight. If the 800mah battery and body thickness are thinned, it will be more perfect.
@suvonkarmanna2924 3 жыл бұрын
Can you give me the model .step file?????
@jlabord 3 жыл бұрын
Bravo
@DmitriSkif 3 жыл бұрын
Waiting for the drone killer from Terminator Universe!
@genuissr 3 жыл бұрын
Vcoptr Falcon missing
@ongluong5375 2 жыл бұрын
Bộ kít này còn không ah
@alessandromototaxi 3 жыл бұрын
Top !!!
@hanswurstusbrachialus5213 3 жыл бұрын
Why is it so dirty around you?
@bastardm7435 2 жыл бұрын
Sadly link for stl download is broken 🙁
@Silverturky 3 жыл бұрын
very very cool but its a shame the motor wires don't run inside the arms a hole on the other side would easily solve that problem and mounting them the opposite direction
@goryny476 3 жыл бұрын
Круть)))
@HK_0101 3 жыл бұрын
Lok Home Market🎊好撚正
@sabinfigaro8272 3 жыл бұрын
Que tan grande se puede construir..?
@motoertroemi 2 жыл бұрын
Hello, I have a problem. The flight controller is no longer available anywhere. Does anyone know an alternative???
@sciencefun5059 2 жыл бұрын
Hello, of course you can use other flight controller, I found a guy build this model on youtube, he used other FC and it fly very well, you can check here: kzfaq.info/get/bejne/i9F2dqhjmpO8hKc.html
@mohammedmostafamamun7112 2 жыл бұрын
sir... can you give me a copy of this stl file... if possible its really helpful for me... thanks
@deniermawan371 Жыл бұрын
if I want to order how much the price? 😊
@syamriothman4298 3 жыл бұрын
you guys do realise the Scorpion ain't the first or only dual rotor copter... The Orca Fighter to me is the first to be made known of its existence.. its idea.. Anyone in the gaming community should know what i mean..
@kkuenzel56 4 жыл бұрын
This is so cool! I'm inspired to print and build this project! What are you using to program your flight controller? Does it have different flight modes? The Banggood sight doesn't really say.
@sciencefun5059 4 жыл бұрын
:D thanks for you interesting in my model. I using Betaflight for setup Flight controller, I have video setup, please check in my channel
@JoseCarlos-ol3ul 4 жыл бұрын
Firmware? Inav? Arducopter? Configuración? Thanks
@sciencefun5059 4 жыл бұрын
I have video setup, please check in my channel
@ainguyen-ip3tl 3 жыл бұрын
Ko biết bác vẽ file in bằng phần mềm gì vậy ạ? Đẹp thực sự
@sciencefun5059 3 жыл бұрын
Fusion 360 bạn
@ainguyen-ip3tl 3 жыл бұрын
Cám ơn bác nhiều ạ
@Idlyresearching 4 жыл бұрын
No programming at all needed?
@sciencefun5059 4 жыл бұрын
I have video setup, please check in my channel
@NexusIncorporation 3 жыл бұрын
i cant belive HAHAHAHA yesterday i bought me a 3D Resin printer this was one of the first hings i wanted to do i Love the Samson SA II - Gunship since i saw Avatar the first time lol and now like ten years later there yougo here is a STL file 😂😂😂😂😂 one more sighn i did right witth buying that Printer (and get broke af lmao) Thank you for sharing that i really hope that my Photon mono can print that thing.... Hell i never, absolutely NEVER thought that would have been my first aerial Vehicle.the only question i have where the heck you get this extendet tips for the superglue ? 🤯
@sciencefun5059 3 жыл бұрын
Hi, thanks for you interested in my model. i did not really understand your question about "extendet tips for superglue?
@NexusIncorporation 3 жыл бұрын
@@sciencefun5059 on your superglue bottle are these long "needle" tips and i wonder where you got them from.
@sciencefun5059 3 жыл бұрын
@@NexusIncorporation oh, it included in the bottle already, i bought in local shop in viet nam,
@NexusIncorporation 3 жыл бұрын
@@sciencefun5059 ah ok, well thats a bit far from me since im from germany lol Thanks anyway ^_^
@BHARGAV_GAJJAR 3 жыл бұрын
Cool project 👍kudos on skipping usual chit chat BS and showing flight first
@namhugo2176 3 жыл бұрын
kênh toàn người nước ngoài xem thế này :D
@STARWALKER_007 3 жыл бұрын
Can you make a dragonship that in the avatar movie plz
@gianclaudiomoresi9650 3 жыл бұрын
Fastastic!
@sea_shield 3 жыл бұрын
Я думал трубки что-бы провода спрятать, а оказалось нет
@karlsonsjekabsonsneiburgso4271 3 жыл бұрын
Please make marvel quinjet (the old one)
@yusufyusuf7565 3 жыл бұрын
Can i buy you avatar RtR...FROM MALAYSIA...PLZ..
@ngoprekmania112 4 жыл бұрын
File STL
@buitrantrung2025 4 жыл бұрын
Ủng hộ việt nam
@Chris-fj9ir 4 жыл бұрын
How much?
@sciencefun5059 4 жыл бұрын
Please take a look at link below video on Cults
Craft Channel
Рет қаралды 1,5 МЛН