Also check out DIY KUNDAN meenakari necklace kzfaq.info/get/bejne/Y9ylepSAxLTTYGg.html DIY finger rings using mouldit kzfaq.info/get/bejne/pKh2hbR5prW4fY0.html
@shamimajamal60214 жыл бұрын
Beautifully done👌
@kavithakavithalaxmanan13054 жыл бұрын
How to seal the color? Its peeled of from my jewel. Shall i use nail polish gloss?
@thelazydiylady37064 жыл бұрын
Using matte paint will avoid peeling off. If you are looking for a glossy look you can seal it with varnish or modpodge. If modpodge isn't available you can dilute pvc glue in water and apply. Hope it helps.
@kavithakavithalaxmanan13054 жыл бұрын
@@thelazydiylady3706 thank u. Shall i use wood varnish?
@thelazydiylady37064 жыл бұрын
Yes. But make sure it dries completely before touching else it ll leave marks and its very hard to get rid of it.
@thelazydiylady37063 жыл бұрын
Check out navratri special ideas kzfaq.info/get/bejne/ppp1rNKmqNCzgpc.html
@tharanipriyagopalsamy69114 жыл бұрын
Its that gold powder is water proof and instead of gum u used which can i use? bcoz that are not available at local area
@thelazydiylady37064 жыл бұрын
Yes it is waterproof. It sticks on to it when u apply it when the base coat is already wet. Fevi bond works good :)
@tharanipriyagopalsamy69114 жыл бұрын
@@thelazydiylady3706 thanks for ur reply at ur precious time😊
@thelazydiylady37064 жыл бұрын
My pleasure. Do subscribe and support. Dropping in diy meenakari necklace for ur further reference kzfaq.info/get/bejne/Y9ylepSAxLTTYGg.html
@thelazydiylady37064 жыл бұрын
Learn to make Antique Kundan pendant using fevicryl mouldit kzfaq.info/get/bejne/ldyJpc2bz5O6oKc.html
@dheerajsaini46233 жыл бұрын
Ye hard nahi ho raha hai. What can I do?? Plz reply
@thelazydiylady37063 жыл бұрын
You have to mix equal amounts from both the packs and mix through. If it is not kneaded properly it willnot harden
@thelazydiylady37063 жыл бұрын
Check out navratri special ideas kzfaq.info/get/bejne/ppp1rNKmqNCzgpc.html
@manusanu50784 жыл бұрын
Which type gum ur using ; after making fire it?
@thelazydiylady37064 жыл бұрын
Hi, the gum used is B- 6000 and No, mouldit clay dosen't need to be burnt. Just knead the contents and let it airdry for about 4 hours.
@manusanu50784 жыл бұрын
@@thelazydiylady3706 thank you dear for ur reply
@thelazydiylady37064 жыл бұрын
My pleasure! Also do check out our DIY ring video, kzfaq.info/get/bejne/pKh2hbR5prW4fY0.html Hope it helps
@radhikadevin21374 жыл бұрын
Where can we get this gum?
@thelazydiylady37064 жыл бұрын
I got it from a local jewellery making material store