TO THOSE WHO USE OMRON ENCODER THIS IS HOW I GOT MINE WORKING!!! ARDUINO - RESISTOR - ENCODER 5V - NONE - Brown and Shield wire (5v and GND) GND - NONE - Blue wire(0v/Common) 0 - 4.7k resistor to 5v - Black wire(A phase) 1 - 4.7k resistor to 5v - White wire(B phase) 6 - 4.7k resistor to GND - Orange wire(Z phase) I literally have no idea why this works, but after hooking it up it works for me like a charm. Also, when using this config, WheelConfig initially will show firmware 0.0, disconnect Z phase's resistor until it becomes the correct one. Let me know if this helped!

best tutorial found so far ,thankyou

Guys help please, I connected everything as in the video, but the encoder did not earn what to do?

I connect my arduino pro micro to my pc with firmware installed and everything works but wheelconfig doesnt register the movement of my 600ppr encoder. I wired everything exactly like in the video. Sometimes it says calibration error

Tested with Arduino Pro Micro and G25 Encoder and its working :D thank you!

for the encoder it works in the program dev has to be connected all the peripherals

The printer encoder is cheapest solution but its not resistant than the omron one but i think the solution is making the rotary encoder case with sensor inside like the omron Edit: i havent try but i will try it when im become the college student

wah keren nih, keren kayanya kalo punya satu dirumah wkwwk itu pake dc motor apa kang kalo boleh tau, pengen bikin saya wkwkwk

Awesome project! Is the arduino leonardo fast enough to read encoder interrupts without loss of centering? With your printer encoder (about 2000 - 2500 ppr), did you notice any loss of center? I'm thinking of using a dead G27, it uses 60ppr encoder, but there is a reduction box that increases to around 1000ppr.

Hello; why the encoder LPD3806 rotates unr in one direction although I have followed the schltplan in the description

Hi. I have question. Is there any possibility to set much more rotation to encoder? Because I have engine with encoder. The problem is, the engine (so is encoder) has 378:1 gear ratio.

Thank you so much man, the trick help me a lot.

I bought a Chinese encoder, I turned it all right, A & B phase and a toogle switch on button 6, but I have no motion no program, what can it be? (sorry for my English shit)

Hi, I have OMRON E6B2-CWZ6C 5-24V 1000P/R. If I connect him to the arduino without resistance and with resistance doesn´t work.

what software u used, please ... I can't find it!

Which motor did u use? Motor + encoder combo is awesome idea. I wanted to do that. its something like DD wheel.

I've bought omron rotary encoder CWZ1X and it has 6 phases, how do I connect this to the arduino?

Hello, I have a few problems. I connected my encoder (cheap chinese, AB) like you in the video, but the firmware version changes just some times. After the version is 0.16, I connected the Z axis with your trick, but the little triangle isn't moving when I rotate the shaft. The number of the X axis also don't change (around 32000). Do you know what I'm doing wrong?

Which engine is much stronger, 775 or hitachi? Is it possible to insert an encoder disc into the back of the 775? Since it is the fastest axis, to have better encoder precision.

I can send a photo as I connected the cable

Can i use photoelectric sensor for steering wheel

Hello. Great project. Could you please tell me what type/model engine is this video? Thank you.

Hey i connected everything according to ur wiring schematics but my pedals are not working..... I m using a 10k potentiometer.... Can u elaborate more on pedal connections and configuration....

the encoder that you used in the video of how many ppr is it?

I baught a encoder 600ppr, i all connect all right, but not working, when i install resistor 1k but to nothing, help me

Just for an inquiry.. when you are using the cheap chinese encoder, if you set the turning angle to 270 degrees when calibrating the steering wheel will it stop on 270?? or can I still turn the wheel but the turning angle does go beyond the 270??

Incremental optical rotary encoder 600/2400 pulse (600 PPR | 2400 Counts) Can I use this encoder

a few questions 1. can I use a geared or servo motor 2. is there a limit on torque (im buying a motor with 30nm of torque) 3. is a motor needed 4. how to connect motor to encoder (if a motor is even needed) 5. I know this question isn't in correct video but is there a max voltage on the moto shield (the motor takes 110v) plis reply

im a little stuck i have the CWZ6C encoder but reading through the comments im not sure if i should add the 4.7k resistors to: A=5v 3.7k resistor B=5v 3.7k resistor z=5v 3.7k resistor Or do i just add the 5v to Z with no resistor or no 5v at all

i am using a encoder and sensor from canon printer, its not same as in your video but i connected it the same way and the problem is that it doesnt detect any motion even while using your trick. it has 5 wire output and i'm using 4 of them as phase A,B,+ve,-ve by your diagram

hi bro, i bought rotary encoder 1000PR from aliexpress, and connected. Wheel COnfig say is " wheel ready" but no response.. what is a problem?

Hello i tried using printer encoder but the emc lite program gives me 0 and -1 and the wheelconfig just changes a little from 32260 to 32240 or something im guessing it just moves 1 step can anybody help

I'm not going for feedback wheel, so I just need to install rotary encoder?

Hello I have such a minor problem in wheel config everything works but when I turn on ETS 2 game it does not detect driver as I give it to the game thank you

can I use L9110 motor driver to connect the Encoder? or just BTS7960 drivers only??

Can i use just a potentiometer instead of the rotary encoder?

El encoder se puede cambiar por un potenciómetro ?

Hi, I want to read encoder value with my dc motors using bts7960 motor driver. Could you please share the code?

is it possible to use a hard drive/cd or dvd drive motor as the encoder?

hi my firmware version stays on 0.0 but the triangle moves when i move the steering wheel, i cannot con figuere it what it is?

Hi there! I am going to be using a leonardo in a Logitech MOMO racing wheel. The wheel itself has a PCB that reads a white line on the shaft so it knows when the wheel is centered. How do I go about connecting this to the Arduino board? Do I hook it up to encoder Z pin? If not, how would the wheel calibrate itself? I'm using a motor with a built in encoder /the factory momo one/.

what is the song name mang? hahaha arenakeun wae uyyy musikna cadasss kwkwkw btw awesome tutorial mang :D

awesome! I'm thinking of building a ffb flight yoke. can this program output two or more axis I.e roll and pitch (and perhaps rudder)?

Can we use the scroll of a mouse as an encoder??

Hello, I finally got a Rotary Encoder 600P / R 5-24V (before I used to use a printer encoder), but when I connect to the arduino the wheel does not move, I measured the voltage that comes out of the phases with a multimeter, and does not leave 5v, nor close to it, is that the problem? do you know how many volts does the TX and RX arduino pins support? Thanks bro

Hello, what is the engine you use? Is there an encoder on it? Can any encoder motor be used in this application?

I use canon ip2770 encoder, but always said calibration error, can you help me?

Hey.. I have the encoder from a printer. How to connect the wires? Appriciate if you can help me..

HELLO I'M TRYING TO DO THIS DESIGN BUT WHEN CONNECTING INCREMENTAL ENCODER 600 PPR HE WILL NOT TELL YOU THE PULSES CAN ME

Mine keeps coming up with calibration error. How do I fix this?

Can you help I am also making this project wiring of encoder get problem to my project

Do you need to upload a sketch to arduino?

I dont see the " wheel state " in my ai config

please help i need a wiring solution for the CWZ1X omron encoder, what can i do.

Can i use geared motor with built in encoder?

less ppr = less precision ???

Hello need little help why my encoder not responing 2 phase software wheel config blinking

Encoder 5V to GND?

How does the arduino knows when the wheel is center with this setup ? This is a incremental coder 🤔

my arduino R3 uno does not display under gaming device @0:51 . please assist

What about connecting the A,B encoder? Requires the corrected schematics except the switch trick? Because i'm tryin it but the WheelConfig software tells ''Wheel error'' or ''Calibration error'' Regards

Punyaku kabel Vcc Ov A B G itu yg di pakaoi A & B saja atsu gmn..

gan udah pake omron cwz6c udah di wiring tapi aneh. kalo input phase ditaro sebelum resistor di apps tulisannya ready dan kalo ditaro sesudah resistor malah calibration error. tapi dua duanya tetep gak respon gerakan.. gimana ya ??? trus pas z phase nya saya copot dan diganti pakai switch malah ngedetect gerakan.. duh bingung.... oya btw itu wiring schematics nya agak ambigu... itu yang merah crossing ke kabel input nya emang nyambung atau tiap input resistornya sendiri sendiri...? oiya saya pake resistor 1k

would be amazing if you upload more videos regarding this diy project,would love to build my own racing sim. can you please give me all list of materials needed for this project? im planning to build this coming holidays, would be great if you help me out, can you give me the list of needed materials?

nice video! will it work witch multi-turn potentiometer 20kΩ?

have an issue. I grab my encoder from my printer and it is a bit different(it's HP) It has flat cable, importantly I don't know where is gnd a,b and 5V I couldn't find any schematics or pinout of it. Can anyone help me? I just wanna know where is gnd, a,b and 5V... These are my pictures of the encoder. s4.dosya.tc/server11/2suk6a/MyEncoder.rar.html PLEASE

Can I use a Hall effect sensor? I'm salvaging a t300rs and it comes with a Hall effect sensor mounted to the motor.

Hi guys, I have a steering wheel with arduino leonardo, everything is ok but I have a little trouble with the wheelconfig software, sometimes it can not status ready, instead of status homing, after a while it will be calibrate error When I tested it on the board, it was still ready and I was able to play FFB until recently. It was not ready for homework, I did not know how to handle this, hope you can help. Thank you very much

Thank you !

is it possible with arduino NANO or UNO?

Kalo di encoder z itu biasanya kabel warna apa ya..

Hello~ i have question.. i have Arduino Leonardo, Bts 7960 and E6B2-CWZ6C 1000ppr Encoder.. As shown in the video, I connected the three products and the motor respectively. The wheel works. But When the motor connects the power to the motor board, the motor continues to run in one direction without stopping. By turning the wheel left or right, only the direction of the motor rotation changes, but it turns without stopping. I really don't know. Ask for advice. If anyone knows.. please :)

Anyone please help im using a normal 2 phase A B encoder but it doesnt detect my rotation in the software and says calibration erro please helpp

Why does my device status display ready, but turning the encoder has no effect

Boleh saya guna rotary encoder sahaja?

Gan kalo encoder nya pake yang a,b,z berarti bisa kaya potensiometer ? Dan z nya gak ngeyel ngeyel lagi kaya pake encoder printer?

can i use arduino uno r3 with this software?

Hi, could you use a potentiometer, made from a hall sensor? (Google Translate)

can I use an encoder like this @t when I use this encoder my steering keeps skipping if I move it left or right suddenly if anyone has a solution it would be of great help. I am unable to get a printer encoder

Any brand encoder is working ?

Pls help,I have connected encoder to board but not showing the encoder moving,I also tried using registers in a and b phase ,so pls help(sorry for bad English)

I connected everything according to the scheme but I have the "calibration error" message

Hello great project .. can i use arduino uno r3

Whats up! I've got problem connecting OMRON E6B2-CWZ6C. Its just not responding. Did every step. Does it have any special way to connect? Thanks!

Another doubt. Where I find the code for the Arduino?

1k or 4.7? many ohms?

why it dont connect? At stats is "calibraton error" and encoder doesnt work? What can I do?

Sir, can i use Orange 600 PPR 2-Phase Incremental Optical Rotary Encoder ?

Hi! The chinese rotary encoder works 900 degrees?

hi my friend, what is the brand of this motor encoder that you are using? I would like to know if this one would do it, ugfmed-b5lr

Sir i have arduino uno r3 And i just wanted to make without ffb steering wheel I have made steering wheel 3 pedals and H-shifter but can you please help me to find codings for arduino uno r3 Coding which contains 4 axis like 3 pedals and 1 handbrake and x&y axis for steering wheel and some button options for gears and other funtions please please please help me sir

assetto corsa only use constant force with air-wave. is that normal?

can i use arduino uno r3, or chinese replica of arduino with atmega32?

Gan, aku sudah buat dan bisa di software rfr wheel configuration nya, tetapi saat tak coba di game forza horizon 3, arduino controlernya gak kedetek, menurut agan, solusinya biar kedetek di game forza horizon 3 bagaimana ya caranya?

hello i have a e6b2-cwz6c encoder connected to my arduino leo. followed it all in the schematics but my encoder cant seem to input anything.

If I use an cheap chinese encoder, just connect to the circuit, ok? I won't need a external sensor, right?

Can you please tell me what motor you are using?

Can i stil connect ip 2770 sensor in arduino leonardo without power supply since i dont need ffb

you used hitachi d06d304e ?

Can anybody help me, If I use omron encoder do I need dc motors