DIY Automated Glass Bottle Cutter

Рет қаралды 268,750

Ай бұрын

There are lot of methods to cut glass bottles, but non of them could make the job easy and effortless as this Automated Glass Bottle Cutting Machine. It could slice bottle after bottle in seconds!
Main used parts:
- Heating Element Coil Wire 2kw - shorturl.at/uBKY8
- Microwave Turntable Motor 5/6r/min - shorturl.at/cuGHW
- AC Voltage Regulator - shorturl.at/oswIX
- Double Rocker Switch - shorturl.at/wzMOV
- Tubular Crimp Terminals - shorturl.at/lEHN0
- Silicone Wire - shorturl.at/eilr0
- Spiral router bits - shorturl.at/cjnAP
Music by Epidemic Sound (www.epidemicsound.com)

Пікірлер: 136

@rafezetter8003 Ай бұрын

I can see the score line made with a glass cutting scribe first. The bottle doesn't have one, then it appears : @9:07 and is NOT in the same parallel as the heating coil. The coil on it's own cannot give such a precise cut - at least be honest about it.

@copernicofelinis Ай бұрын

Can you remind me what day it is?

@gannas42 Ай бұрын

@@copernicofelinisAt the time this video was posted it was March 31st. Even if an April Fools joke it isn't funny nor obvious which makes it at the very least an extremely lame attempt at a prank.

@hitkill35 Ай бұрын

@@gannas42 Even if it was a bad joke, he would always find someone to make him laugh. Why did I feel like swearing?

@_DML_ Ай бұрын

Then there's the misleading thumbnail.

@tednelson5277 Ай бұрын

This is bloody annoying that he left out thr essential scoring of the bottle.

@DR-zi3wz 29 күн бұрын

"Just Insane" - You are correct. The bottles obviously have a cut-line from a glass cutter scribed into them near the where the heater wire contacts the bottle. The wood-working looks nice though.

@megan_alnico 28 күн бұрын

I noticed that too. Why fake it?

@jbbolts 28 күн бұрын

@@megan_alnico Yes why waste people's time

@jbbolts 28 күн бұрын

I'm guessing this was released on April 1st, 6 days ago?

@broniusale5987 27 күн бұрын

@@megan_alnico I think the line is from rubbing on hot coil.

@jacobhoffman2553 17 күн бұрын

he didnt fake it - cheap as fuck to make it and try it - it works - im not sure what application your cut bottles will have tho.... not many countries make the fuckers any more so why? just why? dipshits... (things that no longer generate revenue in RL are shared with ppl on youtube... gold mining gem mining ect... first they strip the mines and when it is no longer profitable they make money off of telling you how to do it)

@DaveEtchells Ай бұрын

Cool project - this is actually one of the ways lens manufacturers cut up slabs of high-grade optical glass.

@hippie-io7225 Ай бұрын

Good design. Elegant and illustrates principles of alignment and jig construction. Well done!! If I build one of your units I would add a small ruler to the base, for more repeatable cuts.

@Sean_but_Not_Heard 18 күн бұрын

I think the “score line” people are seeing is the hot wire smearing onto the very hard glass. This glass-cutting trick is repeatable with a string soaked in fuel around a glass bottle, lit on fire, and then cracked with cold water. The thermal shock cracks the glass along the line of greatest tension, which is the very hot, thin outside line where the string burned or the coil rode.

@sammccormick1 Күн бұрын

I built this. I used a smaller 3mm heater coil . I added a 3mm ceramic rod inside the coil which made it more robust. It cuts extremely well, no scratching required.. Do not listen to the trolls.

@eCitizen1 Ай бұрын

A very nice and beautiful build. I like how clean, functional and organized your tool is. Thanks for an enjoyable video

@viorsa8200 Ай бұрын

Magnífico proyecto maestro, gracias por compartirlo, un cordial saludo y por supuesto un merecido like desde Narón (Galicia)👍🤓😜

@chrisb2557 28 күн бұрын

Very impressive!! Love your creativity. Makes crafting easier for sure. Thank you for sharing.

@maxenielsen 26 күн бұрын

Very well and thoughtfully done! Thank you!

@-.blackraven.- 28 күн бұрын

questions why wood you want to cut a glas bottle

@davidparry2709 6 күн бұрын

To make drinking glasses out of them… Duh.

@samuelfellows6923 Ай бұрын

🤨 ~ April fools joke/fraud, he has to scratch the bottle before putting it on this rotary heater thing, and doesn’t show that? Have I been click-bated with the fake thumbnail? 😡

@x_and_e Ай бұрын

There are multiple projects of similar construction. Just search.

@wf8933 Ай бұрын

Great job!

@OutOfNamesToChoose Ай бұрын

If you change the position of the heating elements, youve got the beginnings of a rotisserie machine!

@tasuja7761 15 күн бұрын

Спасибо за интересный урок, я резал стеклорезом, но ваш способ быстрее и производительнее

@carloshnunez Ай бұрын

Great job very proffesional 🔵🔵🔵🙂🙂🙂👍👍👍🔵🔵🔵

@blessedandhighlyflavored5381 Ай бұрын

I enjoyed this video

@maxpolaris99 Ай бұрын

I wonder if some narrow guage nichrome wire like they use to cut styro foam would work to make spiral cuts on a bottle,

@DewPrototype Ай бұрын

There is some videos on YT about that, its a bit hard, coz every bottle has it own internal tension, what are unpredictable cracks glass when youll try to break it, and usually finishing "spiral cut" is done manualy with some diamond tools

@ErinCollective 28 күн бұрын

this is really cool, i was thinking of using a microwave motor to make a rock tumbler, if you are looking for ideas maybe you could make one? :)

@TNI.496 Ай бұрын

Great work bro❤

@MCsCreations Ай бұрын

Man, that's just brilliant! Really well done!!! 😃 Stay safe there with your family! 🖖😊

@bogganalseryd2324 26 күн бұрын

he's faking it, there are scoring lines after glass cutters

@DrWoodyII Ай бұрын

Brilliant. Thank you for sharing.

@christopherstaples6758 Ай бұрын

its April right ?

@DewPrototype Ай бұрын

Man, you cheating, I see that video is "glued" when you cutting bottle from "top" view, and also I see on side view there is glass cutter instrument lines onto the bottles.

@swatcat7928 Ай бұрын

The line is from the friction with the heating coil.

@DewPrototype Ай бұрын

@swatcat7928 you think that this polished wire is harder than glass? BTW, this method is working well, but it really hard to get that nice finished cut surface without prescratching it with tool. If you try to do something similar you'll discover that "crack" will be not so even and clean.

@swatcat7928 Ай бұрын

@@DewPrototype it is 1000c wire..

@danimalmaxasis2762 Ай бұрын

That line you think you see is a reflection from the edge of the brick that's why it moves when he slides the cradle!

@aserta Ай бұрын

Yup. There's a score line. This is BULLSHIT.

@rojerrojer1310 Ай бұрын

Wonderful

@lasertivo Ай бұрын

What is the brand / model of that tubular crimper?

@Lee-xu2wb Ай бұрын

Very cool!

@dmisi1 Ай бұрын

Fantastic !!!

@skinkie Ай бұрын

I have a rather stupid question. I tried this kind of heating wire as well, even smaller ones rated for 1000W. But without stretching it first, it would directly short ciruit when applied with 230V. You measure only 400W that is quite a substantial difference. Is this only due to your regulator that stops too much power going in?

@Falling_Down_1776 Ай бұрын

We can see the scribe line...🙄

@jimjimgl3 20 күн бұрын

Most impressive is the score line on the bottle that will remain unnamed....

@wardgross2031 Ай бұрын

any links to the silica blocks?

@tianxiu 20 күн бұрын

I wonder how thin the ring can be made?

@bootdoc120 4 күн бұрын

Where do you get the silicate block?

@joedirt1965 Ай бұрын

How do you round the edge so you can drink out of it?

@Adeathwishtolive 20 күн бұрын

Using sandpaper, gradually decreasing the coarseness/ increasing the fineness until you achieve a very smooth finish. Lots of work unless you build a jig to do it for you. If you do want to drink out of it, make sure you sand the edge off in a well ventilated area and wear a particulate filter mask because glass dust is not good for you to breathe, and thoroughly clean the freshly rounded edge

@jeremiahbullfrog9288 Ай бұрын

What is "silicon block" and where do you get this?

@fleaniswerkhardt4647 Ай бұрын

It looks to be the same thing as Hebel block. It's just lightweight autoclaved cement.

@simontillson482 Ай бұрын

Looks like aluminosilicate furnace block to me.

@jeremiahbullfrog9288 Ай бұрын

Thanks guys, looks like either of these would work... maybe the aluminosilicate (also known as "fire brick") might be easier to obtain? I appreciate the pointers

@gannas42 Ай бұрын

So are we just going to pretend we don't notice you scored the bottle with a diamond cutter and then attempt to conceal this by cutting up the footage? Why lie about this?

@user-dk4xi4kd6s 15 күн бұрын

Молодец ,старается вот только стеклорез не кто не отменял)

@myronmire4463 26 күн бұрын

Great job

@tv1453samsung-oq4ni Ай бұрын

👍👏

@FelixLantiguaCamacho 20 күн бұрын

Why would you need to cut a glass bottle for?

@metamol_brain_violet 22 күн бұрын

it's an amazing tool! cool!

@sulaimanachir5500 29 күн бұрын

My English is not good, so I watched it several times to understand what is explained in this video, thank you

@homemadetools 25 күн бұрын

Probably the nicest glass bottle cutter we've seen. We shared this video on our homemade tools forum last week, and people really liked it. 😎

@ShaneMclane-PrivateEye 6 күн бұрын

You score it before putting it over the heated coil for more precision. He didn't include this step in the video because you don't need to score the bottle to achieve a cut, but it helps achieve more accuracy in the result of the cut, as mentioned above. Maybe do a little research before slandering a good product.

@markjones116 Ай бұрын

My minds blown

@changokkim9459 27 күн бұрын

와우~놀랍네요 주문하고 싶어요

@bethannesgarden 14 күн бұрын

This was cool! Thank you!

@adorbstotesadorbs.9371 14 күн бұрын

I made this. It works flawlessly. Naysayers sre flat out wrong.

@libral20 23 күн бұрын

Awesome

@spaced4448 3 күн бұрын

Really good 👍🏼

@ZiyanJunaideen 20 күн бұрын

What is that block?

@Edmorbus Ай бұрын

Well Done Thanks for sharing

@romzesdemon Ай бұрын

это лучшая система нарезания бутылок

@bryanteger 22 күн бұрын

Dude you can see the score line. This bottle was obviously scored first.

@jimmcdougall9973 Ай бұрын

Great idea and very tidy work.

@mavigogun 18 күн бұрын

Obviously the score line was omitted from the video until the cut. REPORT THIS VIDEO FOR MISINFORMATION- click on the "..." below the video>Report>Misinformation

@BreezeLive98 13 күн бұрын

Do patent and open the sales company! Патентуй и открывай компанию продаж!

@lucentrecords7139 14 күн бұрын

Impressive work but… whats the point of this machine?

@AutoMaticTv 29 күн бұрын

Piles bro piles

@gracegarden5716 27 күн бұрын

proč jste to nejdřín naříznul, na lahvy je to vidět

@royrice8021 29 күн бұрын

He forgot to mention to score the glass first………🤔🤨

@ashe1.070 28 күн бұрын

There’s an obvious scribe line. What do you gain by misleading people?

@hitkill35 Ай бұрын

You drew it with diamonds before. Who are you kidding? If you hit it on the table after drawing it with a diamond, it will still be cut in the same way.

@MASI_forging Ай бұрын

Great work dude 👏👏

@Livingstonshoedios 8 сағат бұрын

so were just going to pretend it wasn't scored?

@normandothegreat Ай бұрын

😳👍

@Bumblebee_VS 27 күн бұрын

Admit that the bottles were previously scored with a glass cutter. You can see the outline. Translate with Google

@ebrahimfaiz8522 Ай бұрын

Great idea, well executed. Very impressive job.

@itsgoodforyou4235 19 күн бұрын

This device is as beautiful as it is useless.

@ch1pnd413 28 күн бұрын

Probably should have mentioned how dangerous that silica dust is, silicosis is not a disease you want to mess around with, those white blocks are great, but they’re also dangerous for your lungs

@redmir619 21 күн бұрын

Круто капец !

@Maggioretom Ай бұрын

Really..? All that work for a 1 April joke..?!🤦🏻‍♂️

@anelpasic5232 22 күн бұрын

You are not parting the glass that easily without scoring it first.

@Eric_Tennant 27 күн бұрын

🤪

@KN6IXI 26 күн бұрын

This was extremely satisfying to watch

@JDIDDJNZ 21 күн бұрын

We used to put water in a bottle wack it on an oven element and eventually it would crack at the water line( usually) it was quite a regular thing we did as we needed open bottom bottles for a ummmm .... pastime called "spotting " that we do here in New Zealand... Kiwis know what I'm talking about 😉

@montysmythe579 22 күн бұрын

Firstly why do you want to cut bottles, secondly, who would spend hours and buy all the tools to make something that cuts bottles

@SeaScoutDan 28 күн бұрын

Video thumbnail not match video contents.

@cosmicpsyops4529 15 күн бұрын

Report for fraud

@user-qt4tf6xh2g Ай бұрын

It'll be better video.. 👉

@interesting-film 20 күн бұрын

Развод для колхозников 😂

@websitesthatneedanem 7 күн бұрын

Cool .... but a lie! 😠

@olejrgenkiil6735 Ай бұрын

just fake

@alowishusdavander7804 22 күн бұрын

Why dont you show scoring a line around the bottle with a glass cutter...? I mean you can clearly see the score lines when you are dabbing the water on. Moar fake vids I guess, too bad, was pretty cool until you tried hiding that fact!

@kenliu808 29 күн бұрын

All the time and expenses just to cut the bottles and then throw it away.

@AM-jw1lo 27 күн бұрын

He does say touch the line that was heated. ie the line that was heated is the score line. So he is only telling a half truth, but it is still making fine cuts. No thumbs up because you left the glass knife off your list of Main Parts.

@colvinchapman511 25 күн бұрын

I actually believe it works this well without scoring. The consistency of heating in a consistent repeating path around the bottle is enough without scoring. He’s just saying you need to tough the heated zone or “line”