DIY Desiccant Water Catch Can Air Dryer

  Рет қаралды 2,021

Walker Fab Lab

Walker Fab Lab

11 ай бұрын

Пікірлер: 10
@unlockedcomposites7086
@unlockedcomposites7086 5 ай бұрын
Just FYI, I've been using one for about five months and it exploded this evening. I'm just here looking at videos of other people's findings after I've already come to my conclusion. A couple weeks ago I saw some stress lines in it and I figured I would see it to its end because the odds of it happening when I was in the shop were very rare. I came out of the house at about 12 a.m. and heard my air compressor running with no load on it. It's the cyclic pressure spikes that are the demise of the material. I thought it could be a thing but also it was cheap enough for me to gamble with. It was definitely a more violent explosion than I thought it would be. Luckily my security camera and the shop caught it and there is shrapnel nearly to the other side of the shop from where it was. Also, desiccant is absolutely everywhere. It was like a crappy IED went off in here. I just want to give other people a heads up.
@walkerfablab
@walkerfablab 3 ай бұрын
You need to run a regulator properly.😂 sounds like you don’t know what you are doing
@mustangdemon87
@mustangdemon87 2 ай бұрын
You should do your research before you call your veiwers out bro! ​@walkerfablab 😂 you just built a air powered IED! Hope your far away WHEN it blows. Its not the pressure that's the problem it's the residual oil from the compressor that eats the plastic.
@jameschuke4104
@jameschuke4104 Ай бұрын
Lier not over 100 psi you you fucked up
@Christopherbever
@Christopherbever 26 күн бұрын
We need to see that video!
@unlockedcomposites7086
@unlockedcomposites7086 25 күн бұрын
@@Christopherbever Just uploaded the short to my channel now. It is there.
@josephschneider5000
@josephschneider5000 2 ай бұрын
Since this filter housing is designed for water which runs at a lower pressure than a typical air compressor is there a concern about its longevity?
@walkerfablab
@walkerfablab 2 ай бұрын
They will never see the Maximum pressure because there is a regulator in front of the whole system taking tank pressure from 200psi to 80psi then through the whole system and then to another regulator down to the plasma supplying the correct pressure needed for the machine. Works great🤘🏼
How to treat air moisture from the compressor - Tips and Tricks with Jim Colt
7:05
MaverickCNC Plasma Tables
Рет қаралды 10 М.
I Found some VERY RARE Barn Finds plus over 100 Antique Cars on this SECRET Farm!
33:26
Adventures Made From Scratch
Рет қаралды 44 М.
Playing hide and seek with my dog 🐶
00:25
Zach King
Рет қаралды 33 МЛН
Little girl's dream of a giant teddy bear is about to come true #shorts
00:32
Despicable Me Fart Blaster
00:51
_vector_
Рет қаралды 26 МЛН
High Bypass Turbofan Engine Assembly - Educational Model
8:05
2 SIMPLE HOMEMADE TOOLS That Millions Of People Don't Know
10:37
Welding Mask
Рет қаралды 12 М.
Brilliant Tips and Ideas You Can Easily Do at Home
8:12
Mr SunY
Рет қаралды 12 М.
Air Dryers - An Introduction
5:02
PMG Engineering
Рет қаралды 13 М.
Home Built Rock Crawling Buggy Walk Around
0:31
Offroad_Josh
Рет қаралды 6 М.
How to keep your welding fixture table clean and no BBs or rust!
0:27
Walker Fab Lab
Рет қаралды 4,9 М.
TORNO CNC #cnc #cncrouter #máquinacncmaquina #fresadocncm
8:09